2001 TOYOTA SEQUOIA diagnosis engine

DI±122
± DIAGNOSTICSENGINE
316 Author: Date:
2005 SEQUOIA (RM1146U)
1 Connect hand±held tester, and read value of engine coolant temperature.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / COOLANT TEMP.
CHECK:
Read the temperature value on the the hand±held tester.
OK:
Same value as actual engine coolant temperature.
RESULT:
Displayed TemperatureProceed to
±40°C (±40°F)A
140°C (284°F) or moreB
OK (Same as present temperature)C
HINT:

If there is an open circuit, hand±held tester indicates ±40°C (±40°F).

If there is a short circuit, hand±held tester indicates 140°C (284°F) or more.
B Go to step 4.
C Check for intermittent problems
(See page DI±11).
A

A19552
Engine Coolant
Temp. Sensor
2
1THW
E2ECM
E2
B17441
Engine Coolant
Temp. Sensor
ECM
E2 THW
E2
THW
E2
E8ECM Connector
± DIAGNOSTICSENGINE
DI±123
317 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the E2 engine coolant temperature (ECT)
sensor connector.
(b) Connect terminals 1 and 2 of the engine coolant tempera-
ture sensor wire harness side connector.
(c) Turn the ignition switch ON.
(d) When using hand±held tester, enter the following menu:
DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL /
COOLANT TEMP.
CHECK:
Read the temperature value on the hand±held tester.
OK:
Standard: Temperature value: 1405C (2845F) or more
OK Confirm good connection at sensor. If OK, re-
place engine coolant temperature sensor.
NG
3 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the E2 engine coolant temperature sensor
connector.
(b) Connect terminals THW and E2 of the E8 ECM connector.
HINT:
Before checking, do a visual and contact pressure checks for
the ECM connector.
(c) Turn the ignition switch ON.
(d) When using hand±held tester, enter the following menu:
DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL /
COOLANT TEMP.
CHECK:
Read the temperature value on the OBD II scan tool or the
hand±held tester.
OK:
Standard: Temperature value: 1405C (2845F) or more
OK Repair or replace harness or connector.
NG

A19550
Engine Coolant
Temp. Sensor
ECM
2
1
E2 THW E2
B17442
ECM Engine Coolant
Temp. Sensor
E2 THW E2
ECM Connector E8
DI±124
± DIAGNOSTICSENGINE
318 Author: Date:
2005 SEQUOIA (RM1146U)
Confirm good connection at ECM. If OK, re-
place ECM (See page SF±80).
4 Check for short in harness and ECM.
PREPARATION:
(a) Disconnect the E2 engine coolant temperature sensor
connector.
(b) Turn the ignition switch ON.
(c) When using hand±held tester, enter the following menu:
DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL /
COOLANT TEMP.
CHECK:
Read the temperature value on the hand±held tester.
OK:
Standard: Temperature value: ±405C (±405F)
OK Replace engine coolant temperature sensor.
NG
5 Check for short in harness or ECM.
PREPARATION:
(a) Disconnect the E8 ECM connector.
(b) Turn the ignition switch ON.
(c) When using hand±held tester, enter the following menu:
DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL /
COOLANT TEMP.
CHECK:
Read the temperature value on the hand±held tester.
OK:
Standard: Temperature value: ±405C (±405F)
OK Repair or replace harness or connector.
NG
Replace ECM (See page SF±80).

± DIAGNOSTICSENGINE
DI±133
327 Author: Date:
2005 SEQUOIA (RM1146U)
1 Connect hand±held tester, and read the voltage for throttle position sensor data.
PREPARATION:
(a) Enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / THROTTLE POS
and THROTTLE POS #2.
CHECK:
Read voltage value displayed on the hand±held tester.
OK:
RESULT:
Throttle position expressed as percentage and voltage
Accelerator pedal releasedAccelerator pedal depressedTrouble areaProceed toTHROTTLE POS
(VTA1)THROTTLE POS #2
(VTA2)THROTTLE POS
(VTA1)THROTTLE POS #2
(VTA2)Trouble areaProceed to
0 %0 to 0.2 V0 %0 to 0.2 VVC circuit open
100 %4.5 to 5.5 V100 %4.5 to 5.5 VE2 circuit open
0 % or 100 %2.1 to 3.1 V
(Fail safe)0 % or 100 %2.1 to 3.1 V
(Fail safe)VTA1 circuit open or
ground shortA
about 16 %
(Fail safe)0 to 0.2 or 4.5 to 5.5 Vabout 16 %
(Fail safe)0 to 0.2 or 4.5 to 5.5 VVTA2 circuit open or
ground short
10 to 24 %2.15 to 3.05 V64 to 96 %
(Does not fail safe)4.5 to 5.5 V
(Does not fail safe)Throttle position sen-
sor circuit is normalB
B Go to step 5.
A

DI±140
± DIAGNOSTICSENGINE
334 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Fuel cutOFF
EngineRunning
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Time until ºengine coolant temperatureº detection temperature reaches feedback start temperature
When the temperature at the time of engine starting is
±8.34°C (17°F) or moreEngine coolant temperature is less than ºclosed±loop enable temperatureº
when 2 min. or more after engine start
When the temperature at the time of engine starting is
±19.45 to ±8.34°C (±3 to 17°F)Engine coolant temperature is less than ºclosed±loop enable temperatureº
when 5 min. or more after engine start
When the temperature at the time of engine starting is
±19.45°C (±3°F) or lessEngine coolant temperature is less than ºclosed±loop enable temperatureº
when 20 min. or more after engine start
INSPECTION PROCEDURE
HINT:

If DTC P0115, P0116, P0117, P0118 and P0125 are output simultaneously, engine coolant tempera-
ture sensor circuit may be open or short. Perform the troubleshooting of DTC P0115, P0117 or P0118
first.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0125) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTCs using the hand±held tester.
RESULT:
Display (DTC output)Proceed to
P0125A
ºP0125º and other DTCsB
HINT:
If any other codes besides ºP0125º are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI±58).
A

DI±144
± DIAGNOSTICSENGINE
338 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR RESULT
Refer to page DI±26 for detailed information.
The test value and test limit information are described as shown in the following table. Check the monitor
result and test values after performing the monitor drive pattern (refer to ºConfirmation Monitorº).

MID (Monitor Identification Data) is assigned to each emissions±related component.

TID (Test Identification Data) is assigned to each test value.

Scaling is used to calculate the test value indicated on generic OBD ll scan tools.
Thermostat
MIDTIDScalingDescription of Test ValueMinimum Test LimitMaximum Test Limit
$E1$E8Multiply by 0.1
(°C)ECT sensor output when estimated
ECT reached to malfunction criteriaMalfunction criterionMaximum test limit
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0128) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P0128A
P0128 and other DTCsB
HINT:
If any other codes besides P0128 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI-58).
A

A23661
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even if vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolutely constant speed
conditions such as with cruise
control activated. (h)
(g)
MISFIRE MON ..................... AVAILREADINESS TESTS
CAT EVAL ......................... INCMPL
HTD CAT EVAL ...................... N/A
EVAP EVAL ....................... INCMPL
2nd AIR EVAL .......................... N/A
A/C EVAL ................................ N/A
O2S EVAL ........................ INCMPL
O2S HTR EVAL .................. INCMPL
EGR EVAL ...............................N/A COMP MON ........................ AVAIL FUEL SYS MON ................... AVAIL
A76855
A23660
DI±154
± DIAGNOSTICSENGINE
348 Author: Date:
2005 SEQUOIA (RM1146U)
CONFIRMATION DRIVING PATTER
HINT:

This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting
procedure when using either a hand±held tester.

Performing this confirmation pattern will activate the Heated Oxygen (HO2) sensor monitor. (The cata-
lyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the tester or scan tool ON.
(d) Clear DTCs (where set) (see page DI±43).
(e) If using a hand±held tester, select the following menu
items: DIAGNOSIS / CARB OBD II / READINESS
TESTS.
(f) Check that O2S EVAL is INCMPL (incomplete).
(g) Start the engine and warm it up.
(h) Drive the vehicle at between 40 mph and 70 mph (64 km/h
and 113 km/h) for at least 10 minutes.
(i) Note the state of the Readiness Tests items. Those items
will change to COMPL (complete) as O2S EVAL monitor
operates.
(j) On the tester, select the following menu items: DIAGNO-
SIS / ENHANCED OBD II / DTC INFO / PENDING
CODES and check if any DTCs (any pending DTCs) are
set.
HINT:
If O2S EVAL does not change to COMPL, and any pending
DTCs fail to set, extend the driving time.

± DIAGNOSTICSENGINE
DI±155
349 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Hand±held tester only:
Narrowing down the trouble area is possible by performing ACTIVE TEST of the following ºA/F CONTROLº
(Heated oxygen sensor or another can be distinguished).
(a) Perform ACTIVE TEST by hand±held tester (A/F CONTROL).
HINT:
ºA/F CONTROLº is the ACTIVE TEST which changes the injection volume to ±12.5 % or +25 %.
(1) Connect the hand±held tester to the DLC3 on the vehicle.
(2) Turn the ignition switch ON.
(3) Warm up the engine with the engine speed at 2,500 rpm for approximately 90 seconds.
(4) Select the menu ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROLº.
(5) Perform ºA/F CONTROLº with the engine in an idle condition (press the right or left button).
RESULT:
Heated oxygen sensor reacts in accordance with increase and decrease of injection volume
+25 % " rich output: More than 0.5 V
±12.5 % " lean output: Less than 0.4 V
NOTICE:
There is a few seconds delay in the sensor 1 (front sensor) output. And there is approximately 20
seconds delay in the sensor 2 (rear sensor).