2001 TOYOTA SEQUOIA wiring diagram

FI6448
ECM
5 V
THW E2
Engine Coolant Temp. Sensor
2
1G±Y
G±W
E1 E2
E8
E8
2821
± DIAGNOSTICSENGINE
DI±121
315 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs related to different system that have terminal E2 as the ground terminal are output simulta-
neously, terminal E2 may have an open circuit.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.

A19212
T14
Throttle Control Motor
and Position Sensor
4
6
1
2G±W
G±B
P±L
B±Y28
23
19
20
4
5
17 E8
P
VECM
E2
VC
VTA2
VTA1 3
5
(Shielded)
L±RM±
M+
GE01 E8
E8
E8
E8
E8
E8 DI±132
± DIAGNOSTICSENGINE
326 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs related to different system that have terminal E2 as the ground terminal are output simulta-
neously, terminal E2 may have an open circuit.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.

± DIAGNOSTICSENGINE
DI±153
347 Author: Date:
2005 SEQUOIA (RM1146U) Heated oxygen sensor impedance
348.1 MW or more
Heated oxygen sensor output voltage (Extremely high):
Duration of following condition10 sec. or more
Heated oxygen sensor voltageMore than 1.2 V
COMPONENT OPERATING RANGE
ParameterStandard Value
Heated oxygen sensor voltageVaries between 0.1 to 0.9 V
MONITOR RESULT
Refer to page DI±24 for detailed information.
The test value and test limit information are described as shown in the following table. Check the monitor
result and test values after performing the monitor drive pattern (refer to ºConfirmation Monitorº).

MID (Monitor Identification Data) is assigned to each emissions±related component.

TID (Test Identification Data) is assigned to each test value.
HO2S bank 1 sensor 2
MIDTIDScalingDescription of Test ValueMinimum Test LimitMaximum Test Limit
$02$07Multiply by 0.001
(V)Minimum sensor voltageMinimum test limitMaximum test limit
$02$08Multiply by 0.001
(V)Maximum sensor voltageMinimum test limitMaximum test limit
$02$8FMultiply by 0.001
(g)Maximum oxygen storage capacity0Maximum test limit
HO2S bank 2 sensor 2
MIDTIDScalingDescription of Test ValueMinimum Test LimitMaximum Test Limit
$06$07Multiply by 0.001
(V)Minimum sensor voltageMinimum test limitMaximum test limit
$06$08Multiply by 0.001
(V)Maximum sensor voltageMinimum test limitMaximum test limit
$06$8FMultiply by 0.001
(g)Maximum oxygen storage capacity0Maximum test limit
WIRING DIAGRAM
Refer to DTC P2195 on page DI±383.

DI±168
± DIAGNOSTICSENGINE
362 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Fuel system statusClosed±loop
Throttle position learningCompleted
Either of the following conditions is met:Condition 1 or 2
1. Engine RPM±1,000 rpm
2. Intake air amount per revolution0.26 g/sec.±
Catalyst monitorNo executed
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Purge±cutExecuting
Either of the following conditions is metCondition 1 or 2
1. Average between short±term fuel trim and long±term fuel
trim35% or more (varies with ECT)
2. Average between short±term fuel trim and long±term fuel
trim±35% or less (varies with ECT)
WIRING DIAGRAM
Refer to DTC P2195 on page DI±383.
INSPECTION PROCEDURE
HINT:
Hand±held tester only:
Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE
TEST. The A/F CONTROL function can help to determine whether the Air±Fuel Ratio (A/F) sensor, Heated
Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the A/F CONTROL operation using a hand±held tester.
(1) Connect a hand±held tester to the DLC3.
(2) Start the engine and turn the tester ON.
(3) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
(4) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE
TEST / A/F CONTROL.
(5) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT
or LEFT button to change the fuel injection volume).
(6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 (AFS B2S1) and OS2 B1S2
(O2S B2S2)) displayed on the tester.
HINT:

The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

A23553
G±R
1 28
A 6
BECM
AM2
W±B6
32
15 3
2 121
3 2B IA1
J5
J/CL±O
I18
Ignition SW
3
7
F10
Fusible Link BlockB±R
BI530
10 26 4
12
2
114
68
1 41
5 3L±B
AM2
52HE6
2D
2F 1J1C2F
IA4
E4
E4 IG4
IA4 2H
2H 2C 1C
1JFPR
FC
MREL B±O5
J44
J45J/C E
L
BB1G±RG±REngine Room J/B
4
2F
5V V V
IL2
25
G±O G±O
B
IG2
W±B
W±BA
ED 5 4G±RIG1
B±WB±W
Instrument Panel J/B
F9
Fuel Pump
Resister
Battery2C
W±R W±R5
6
EFI No.15
C/OPN Relay Fuel Pump
Relay
EFI Relay F19
Fuel Pump
± DIAGNOSTICSENGINE
DI±181
375 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
HINT:
This diagnostic chart is based on premise that engine is started. If the engine is not started, proceed to prob-
lem symptoms table on DI±33.

A15466A19380
Battery I18
Ignition SW
1
#80 #60 #40#20
#70#50ECM
#30 #10
6
2
I10 Injector No.2
I12 Injector No.4
I13 Injector No.5
I14 Injector No.6
I15 Injector No.7
I16 Injector No.8
7
1
2
12
1
2 1
2
1
2
2
2
2 3 2
5
7 4
I9 Injector No.1
1C
2D1
B
F10
Fusible Link BlockIGN2
Engine Room J/B
54
B2C1 1C
1J 1D 2
3
W±R6
AM2Instrument Panel J/B
W±R3
B±R
1
1
1
I11 Injector No.3
IG413
E8 E6
E6
E8 E6 E6
E6 E6
R±W B±R
B±R
B±R
B±R
B±R
B±R
B±RY R±B
L±R W
L G R
B±R B±R B±R
5
IG2
AM2
B±R
B±R
B±R
B±R
B±R
DI±190
± DIAGNOSTICSENGINE
384 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Refer to DTC P0351 on page DI±221 for the wiring diagram of the ignition system.
CONFIRMATION DRIVING PATTERN
(a) Connect the hand±held tester to the DLC3.
(b) Record DTC and the freeze frame data.
(c) Use the hand±held tester to set the check mode (See page DI±44).
(d) Read the value on the misfire counter for each cylinder when idling. If the value is displayed on the
misfire counter, skip the following procedure of confirmation driving.
(e) Drive the vehicle several times with the engine speed, load and surrounding range shown as ENGINE
SPD, CALC LOAD in the freeze frame data or MISFIRE RPM, MISFIRE LOAD in the DATA LIST.
If you have no hand±held tester, turn the ignition switch OFF after the symptom is simulated once. Then re-
peat the simulation process again.

A23549
ECU
KNK1 21
E7
B GR
4 K1
Knock Sensor 1
(Bank 1)B 8
1 K2
Knock Sensor 2
(Bank 2)
1
20KNK2
E7
BR7
2
EB4 EB4
23
EB
EC 1
BR BR
BR
E (Shielded)
BR (Shielded)
EB4 EB4
EB4(Shielded)
(Shielded)
2G
RWW
G
REKN2
EKNK
E1 E6 E7
E7 29
28
BRE D
DJ42
J/C J42
J/C DI±206
± DIAGNOSTICSENGINE
400 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Knock sensor range check (Chattering) P0325, P0330:
Knock sensor voltageLess than 0.5 V, or more than 4.5 V
Knock sensor range check (Low voltage) P0327, P0332:
Knock sensor voltageLess than 0.5 V
Knock sensor range check (High voltage) P0328, P0333:
Knock sensor voltageMore than 4.5 V
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

DTC P0325, P0327 and P0328 are for the bank 1 knock sensor circuit.

DTC P0330, P0332 and P0333 are for the bank 2 knock sensor circuit.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, and other data from the time the malfunction occurred.

A19690
C1
Camshaft Position Sensor
C2
Crankshaft Position SensorLECM
NE+
NE±
E2 27
2 12 1
25
24 Y
R GE6
G2+
G2±
32
E6
E6
E6
*1: ShieldedE6E1
EC (*1) (*1)
J42 J/C
A
AA
BR
BR
BR1 DI±212
± DIAGNOSTICSENGINE
406 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM