2001 TOYOTA PRIUS Front door glass

R13455
10 m (33 ft) or more
SSTBattery
R06753
RS±18
± SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
2001 PRIUS (RM778U)
(4) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(5) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(6) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the negative (±) termi-
nal.
(c) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes af-
ter deployment.

Use gloves and safety glasses when handling a steer-
ing wheel pad with the deployed airbag.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a steering wheel pad with
the deployed airbag.

When scrapping a vehicle, deploy the airbag and
scrap the vehicle with the steering wheel pad still
installed.

When moving a vehicle for scrapping which has a
steering wheel pad with deployed airbag, use gloves
and safety glasses.
HINT:
The airbag deploys simultaneously as the LED of the SST ac-
tivation switch lights up.
2. DEPLOYMENT WHEN DISPOSING OF STEERING
WHEEL PAD ONLY
NOTICE:

When disposing of the steering wheel pad (with air-
bag) only, never use the customers vehicle to deploy
the airbag.

Be sure to follow the procedure given below when de-
ploying the airbag.
HINT:
Have a battery ready as the power source to deploy the airbag.

RS0JZ±06
AB0152
SST
AB0158
SSTBattery RS±30
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
2001 PRIUS (RM778U)
DISPOSAL
HINT:
When scrapping vehicle equipped with an SRS or disposing of
a front passenger airbag assembly, always first deploy the air-
bag in accordance with the procedure described below. If any
abnormality occurs with the airbag deployment, contact the
SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.
CAUTION:

Never dispose of a front passenger airbag assembly
which has an undeployed airbag.

The airbag produces a sizeable exploding sound
when it deploys, so perform the operation out±of±
doors and where it will not create a nuisance to
nearby residents.

When deploying the airbag, always use the specified
SST (SRS Airbag Deployment Tool). Perform the op-
eration in a place away from electrical noise.
SST 09082±00700

When deploying an airbag, perform the operation at
least 10 m (33 ft) away from the front passenger air-
bag assembly.

The front passenger airbag assembly is very hot
when the airbag is deployed, so leave it alone for at
least 30 minutes after deployment.

Use gloves and safety glasses when handling a front
passenger airbag assembly with the deployed airbag.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front passenger airbag
assembly with the deployed airbag.
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Check functioning of the SST (See step 1±(a) on page
RS±16).
SST 09082±00700

H15678
H15679Battery
SST
R13455
10 m (33 ft) or more
SSTBattery
H15680
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS±43
2001 PRIUS (RM778U)
(b) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the SST.
(1) Connect the connectors of the 2 SST to the airbag
connector.
SST 09082±00700, 09082±00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(±) terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
after deployment.

Use gloves and safety glasses when handling the
side airbag assembly with the deployed airbag.

Do not apply water, etc. to the side airbag assembly
with the deployed airbag.

Always wash your hands with water after completing
the operation.

When scrapping a vehicle, deploy the airbag and
scrap the vehicle with the side airbag assembly still
installed.

H15394
Air Riveter
H00475
Mandrel
H15395Protective Tape
H15408
H15407
± BODYFRONT DOOR
BO±13
2001 PRIUS (RM778U)
HINT:
At the time of reassembly, please refer to the following item.
Using an air riveter and nose piece No.1, strike rivets into the
door panel to install the speaker to the door panel.
NOTICE:
At the time of reassembly, please refer to the following
item.
If the rivet is not positioned perpendicularly it will bend the
mandrel. When the trigger is then pulled, it may damage the
air riveter.
8. REMOVE OUTSIDE VIEW MIRROR
(a) Disconnect the connecter.
(b) Remove the 3 nuts andout side view mirror.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
9. REMOVE DOOR BELT MOULDING
Using a scraper, remove the door belt moulding.
HINT:
Tape the scraper tip before use.
10. REMOVE DOOR LOCK SILENCER
11. REMOVE DOOR GLASS
(a) Remove the 3 bolts and reinforce inside extension.
(b) Open the door glass until the door belts appear in the ser-
vice hole.
(c) Remove the 2 bolts.
NOTICE:
Be careful not to drop the door glass.
(d) Pull the door glass upward to remove it.
12. REMOVE DOOR GLASS RUN
13. REMOVE LOWER FLAME
Remove the 2 nuts, plate and lower flame.

BO3T8±01
AB0152
SST
AB0158
SSTBattery
± BODYSEAT BELT PRETENSIONER
BO±93
2001 PRIUS (RM778U)
DISPOSAL
HINT:
When scrapping vehicles equipped with a seat belt pretension-
er or disposing of a front seat outer belt (with seat belt preten-
sioner) always first activate the seat belt pretensioner in accor-
dance with the procedure described below. If any abnormality
occurs in the seat belt pretensioner operation, contact the SER-
VICE DEPT. of the TOYOTA MOTOR SALES, USA, INC.
CAUTION:

Never dispose of the front seat outer belt which has
an inactivated pretensioner.

The seat belt pretensioner produces a sizeable ex-
ploding sound when it activates, so perform the op-
eration out±of±door and where it will not create a nui-
sance to nearby residents.

When activating the seat belt pretensioner, always
use the specified SST. (SRS Airbag Deployment Tool)
Perform the operation in a place away from electrical
noise.
SST 09082±00700

When activating a front seat outer belt (with seat belt
pretensioner), perform the operation at least 10 m (33
ft) away from the front seat outer belt.

The front seat outer belt (with seat belt pretensioner)
is very hot when the pretensioner is deployed, so
leave it alone for at least 30 minutes after deployment.

Use gloves and safety glasses when handling a front
seat outer belt with activated pretensioner.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
the activated pretensioner.
1. SEAT BELT PRETENSIONER ACTIVATION WHEN
SCRAPPING VEHICLE
HINT:
Have a battery ready as the power source to activate the seat
belt pretensioner.

H15464
SST
SST
R13455
10 m (33 ft) or more
± BODYSEAT BELT PRETENSIONER
BO±95
2001 PRIUS (RM778U)
(2) Connect the 2 SST, then connect them to the seat
belt pretensioner.
SST
Driver's side: 09082±00700, 09082±00730
Except driver's side: 09082±00700, 09082±00740
NOTICE:
To avoid damaging the SST connector and wire harness.
(3) Move the SST to at least 10 m (33 ft) away from the
front of the vehicle.
(4) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(5) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the negative (±) termi-
nal.
(d) Activate the seat belt pretensioner.
(1) Confirm that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).
CAUTION:

The front seat outer belt is very hot when the seat belt
pretensioner is activated, so leave it alone for at least
30 minutes after activation.

Use gloves and safety glasses when handling a front
seat outer belt with the activated seat belt pretension-
er.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
the activated seat belt pretensioner.
HINT:
When scrapping a vehicle, activate the seat belt pretensioner
and scrap the vehicle with the activated front seat outer belt still
installed.
2. ACTIVATION WHEN DISPOSING OF FRONT SEAT
OUTER BELT ONLY
NOTICE:

When disposing of the front seat outer belt (with seat
belt pretensioner) only, never use the customer's ve-
hicle to activate the seat belt pretensioner.