2001 NISSAN PATROL Electronic Repair Manual

BODY & TRIM
SECTION
BT
MODIFICATION NOTICE:
+Front grille and bumper assembly have been changed.
+Front grille guard has been added.
CONTENTS
PRECAUTIONS................................................... 2002
Service Notice .................................................. 2002
Supplemental Restraint System (SRS) ªAIR
BAGº and ªSEAT BELT PRE-TENSIONERº ... 2002BODY END.......................................................... 2003
Body Front End ................................................ 2003
EXTERIOR........................................................... 2006
HFor seat belt, refer to MA and RS section.
HFor wiring diagrams of body electrical systems, refer to EL section.

BT

Service Notice
+When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
+Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil
or damage them.
+Apply sealing compound where necessary when installing parts.
+When applying sealing compound, be careful that the sealing compound does not protrude from parts.
+When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust
prevention measures.
Supplemental Restraint System (SRS) ªAIR
BAGº and ªSEAT BELT PRE-TENSIONERº
The Supplemental Restraint System such as ªAIR BAGº and ªSEAT BELT PRE-TENSIONERº used along
with a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. The SRS system composition which is available to NISSAN MODEL Y61 is as follows (The
composition varies according to the destination and optional equipment.):
+For a frontal collision
The Supplemental Restraint System consists of driver air bag module (located in the center of the
steering wheel), front passenger air bag module (located on the instrument panel on passenger side),
seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness and spiral cable.
+For a side collision
The Supplemental Restraint System consists of front side air bag module (located in the outer side of
front seat), satellite sensor, diagnosis sensor unit (one of components of air bags for a frontal collision),
wiring harness, warning lamp (one of components of air bags for a frontal collision).
Information necessary to service the system safely is included in theRS sectionof this Service Manual.
WARNING:
+To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance should be per-
formed by an authorized NISSAN dealer.
+Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and
Air Bag Module, see the RS section.
+Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified with yellow harness connector.
PRECAUTIONS
BT-2002

Body Front End
+When removing or installing hood, place a cloth or other padding on front fender panel and cowl top.
This prevents vehicle body from being scratched.
+Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
+Hood adjustment: Adjust at hinge portion.
+Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood
locks engaging mechanism.
+Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
REMOVAL Ð Front bumper assembly
V1Remove front guard bar. Refer to ªEXTERIORº for details, BT-2005.
V2Remove left and right headlamp wipers (on models with headlamp wipers).
V3Remove clips securing front grille and remove the front grille.
V4Remove screws and bolts securing left and right front bumper side bracket.
V5Remove bolts securing bumper lower to engine under cover.
V6Remove bolts securing left and right front bumper stay upper (without winch).
V7Remove bolts securing left and right front bumper stay side.
V8Extract bumper assembly.
SBT243A
BODY END
BT-2003

SBT244A
BODY END
Body Front End (Cont'd)
BT-2004

SBT245A
BODY END
Body Front End (Cont'd)
BT-2005

Front grille guard
SBT246A
EXTERIOR
BT-2006

CLUTCH
SECTION
CL
MODIFICATION NOTICE:
+Service Data and Specifications (SDS) have been changed.
CONTENTS
CLUTCH SYSTEM............................................... 2002
HYDRAULIC CLUTCH CONTROL..................... 2003
Clutch Operating Cylinder................................ 2003
Clutch Master Cylinder .................................... 2004
CLUTCH DISC AND CLUTCH COVER.............. 2005Clutch Cover .................................................... 2005
SERVICE DATA AND SPECIFICATIONS
(SDS).................................................................... 2006
General Specifications ..................................... 2006
Inspection and Adjustment .............................. 2006

CL

SCL906
CLUTCH SYSTEM
CL-2002