2001 LAND ROVER FREELANDER engine oil

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-1
CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
Capacities
The following capacities are only an approximation of
the amount of fluid required to fill the respective
system.
Capacities – UK/ROW
† An extra 420 cc (0.73 imp pt) is required for
vehicles with an air blast fluid cooler fitted.
* Refill capacity is approx. 0.7 litre (1.125 imp. pt)
less than the from dry figures.
Capacities – NAS
Component / system Capacity
Fuel tank:
Td4 Model
K1.8 and KV6 Models
⇒ Up to 03 Model Year
⇒ From 03 Model Year
KV6 Model
⇒ Up to 03 Model Year
⇒ From 03 Model Year59 litres (13 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
Engine - Td4 (including oil cooler and oil filter):
⇒ Refill 6.8 litres (12 imp. pts)
⇒ Fill from dry 7.3 litres (12.9 imp. pts)
Engine - K1.8 (including filter):
⇒ Refill 4.5 litres (7.9 imp. pts)
⇒ Fill from dry 4.8 litres (8.4 imp. pts)
Engine - KV6 (including oil cooler and filter):
⇒ Refill 5.2 litres (9.125 imp. pts)
⇒ Fill from dry 6.0 litres (10.625 imp. pts)
Manual gearbox - PG1:
⇒ Refill 2.0 litres (3.5 imp. pts)
⇒ From dry 2.2 litres (3.9 imp. pts)
Manual gearbox - Getrag:
⇒ Refill 1.6 litres (2.875 imp. pts)
⇒ From dry 1.67 litres (3 imp. pts)
Automatic gearbox - JATCO:
⇒ Refill 4.0 litres (7 imp. pts)
⇒ From dry
†8.5 litres (15 imp. pts)
Intermediate Reduction
Drive1.1 litres (2 imp. pts)
Rear differential:
⇒ Maximum 830 ml (29.2 imp. fl. oz.)
⇒ Minimum 750 ml (26.4 imp. fl. oz.)
Power steering reservoir 335 cm
3
Cooling system - Td4 Engine – Fill from dry (with
reservoir)*:
⇒ Automatic - Up to 03
Model Year
⇒ Automatic - From 03
Model Year7.25 litres (12.8 imp. pts)
7.35 litres (13 imp. pts)
⇒ Manual 7.25 litres (12.8 imp. pts)
Cooling system - K1.8 Engine:
⇒ Fill from dry (with
reservoir)*5.8 litres (10.25 imp. pts)
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)*7.8 litres (13.75 imp. pts)
Reservoir tank:
⇒ Maximum fill 0.44 litres (0.75 imp. pts)
⇒ Expansion tank volume 1.2 litres (2.125 imp. pts)
⇒ Gross expansion
capacity0.72 litres (1.27 imp. pts)
Windscreen washer
reservoir 4.0 litres (7 imp. pints)
Component / system Capacity
Fuel tank:
⇒ Up to 02.5 Model Year
⇒ From 02.5 Model Year15.6 US gallons
17.2 US gallons
Engine - KV6 (including oil cooler and filter):
⇒ Engine oil and filter
change11 US pts
⇒ Fill from dry 12.7 US pts
Automatic gearbox - JATCO:
⇒ Refill 8.5 US pts
⇒ From dry 18.2 US pts
Intermediate Reduction
Drive2.3 US pts
Rear differential:
⇒ Maximum
⇒ Minimum28.1 US fl. oz.
25.4 US fl. oz.
Power steering reservoir 335 cm
3
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)17.82 US pts
Reservoir tank:
⇒ Maximum fill 0.93 US pts
⇒ Expansion tank volume 2.54 US pts
⇒ Gross expansion
capacity1.52 US pts
Windscreen washer
reservoir 8.5 US pts Component / system Capacity

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-2
Fluids
Fuel
Always use the following recommended fuels:
Petrol engines
Use unleaded petrol with a minimum octane rating of
95 RON to ENN 228 specification.
In an emergency (and only if the correct fuel is
unavailable), lower octane rated fuel can be used for
very limited periods of moderate, low speed
motoring, provided engine 'knocking' does not occur.
Fuels of 90 RON is used in certain markets; 90 RON
fuel can be used regularly ONLY if the engine has
been tuned specifically to suit low octane fuel.
Certain markets use fuel containing a 23% Ethanol
additive.
K1.8 and KV6 engines are also available for use with
a low octane leaded fuel specification in some
markets.
Diesel engines
Use a good quality diesel fuel or automotive gas oil
(AGO) conforming to EN 590 specification.
It is important that the sulphur content of diesel fuel
does not exceed 0.3%.
Ensure the fuel filter element is changed at the
recommended intervals.

+ MAINTENANCE, MAINTENANCE, Fuel
Filter - Diesel.
Brake Fluid
Use only DOT 4 brake fluid. DO NOT use brake fluid
of a different specification.
PAS fluid
Use Texaco 9226 fluid.Anti-freeze solutions
The overall anti-freeze concentration should not fall,
by volume, below 50% to ensure that the anti-
corrosion properties of the coolant are maintained.
Anti-freeze concentrations greater than 60% are not
recommended as cooling efficiency will be impaired.
Use Havoline Extended Life Coolant (XLC), or any
ethylene glycol based anti-freeze (containing no
methanol) with only Organic Acid Technology (OAT)
corrosion inhibitors, to protect the cooling system.
CAUTION: No other anti-freeze should be used
with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and
refilled with the correct amount of anti-freeze
solution at the intervals given on the Service
Maintenance Check Sheet.
After filling with anti-freeze solution, attach a warning
label to a prominent position on the vehicle stating
the type of anti-freeze contained in the cooling
system to ensure that the correct type is used for
topping-up.
The following recommended quantities of anti-freeze
will provide frost protection to -36 °C (-33 °F):
Engine – Td4
Engine – K1.8
Engine – KV6
Concentration 50%
Amount of anti-freeze 3.75 litres
(6.625 imp. pts)
Concentration 50%
Amount of anti-freeze 2.9 litres
(5.125 imp. pts)
Concentration 50%
Amount of anti-freeze 3.9 litres
(6.875 imp. pts, )

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-3
Lubrication
The engine and other lubricating systems are filled
with high- performance lubricants giving prolonged
life.
CAUTION: Always use a high quality oil of the
correct viscosity range in the engine. The use of
oil of the incorrect specification can lead to high
oil and fuel consumption and ultimately to
damaged components.
Oil to the correct specification contains additives
which disperse the corrosive acids formed by
combustion and prevent the formation of sludge
which can block the oil ways. Additional oil additives
should not be used.
Always adhere to the recommended servicing
intervals.
Engine oil
Engine oil viscosity / temperature ranges are
indicated in the following table:
a0W/30; 5W/30
b0W/40, 50, 60; 5W/40, 50, 60
c10W/30
d10W/40, 50, 60
Engine oil – Td4 engine
Use 0W/30 or 5W/40, 50, 10W/30, 40, 60 oil meeting
ACEA A3/B3 specifications, and having a viscosity
band recommended for the temperature range of
your locality. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.Engine oil – K1.8 engine
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine – Non NAS models
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine - NAS models
Use a 5W/40 fully synthetic oil meeting specification
ACEA A3. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.
Gearbox oil
Use of gearbox oils other than those specified may
result in serious damage to the gearbox.
Manual Gearbox – PG1 and Getrag
Use OPEL B 0400063 for refill or topping-up.
Automatic Gearbox – JATCO
Use Texaco N402 fluid for refill or topping-up.
Intermediate Reduction Drive
Texaco S5 75W90; Synthetic oil or equivalent,
meeting: API GL5
Rear Differential
Multigear 80W/90 ETL; Specification: API GL5
Gear linkage - Manual
Use grease containing 3% Molybdenum Disulphide.
General Greasing
Use Multipurpose Lithium Base Grease NLGI
consistency No. 2.
Bonnet latch
Lubricate cable and latch with oil.

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-4
Sealants
The following table lists those sealants which are
used during repair / overhaul procedures covered in
this manual; it is essential that the sealant specified
for a particular procedure is used at all times.
Component Application Land Rover
Part No.
Td4 Engine Camshaft cover
gasket joint linesSTC 50550
Td4 Engine Sump gasket joint
linesSTC 50550
K 1.8 Engine Oil pressure switch
threadsSTC 50552
K 1.8 Engine Oil pressure relief
valve plug threadsSTC 50552
K 1.8 Engine Oil temperature
sensor threadsSTC 50552
K 1.8 Engine Oil pump cover
plate screwsSTC 50552
K 1.8 Engine Camshaft carrier to
cylinder headSTC 4600
K 1.8 Engine Bearing ladder to
cylinder blockSTC 4600
K 1.8 Engine Sump to bearing
ladderSTC 4600
K 1.8 Engine Oil rail to bearing
ladderSTC 4600
K 1.8 Engine Crankshaft rear oil
seal STC 50550
K 1.8 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Camshaft timing
belt backplate
cover boltsSTC 50552
KV6 Engine Oil pressure relief
valve plug threadsSTC 50552
KV6 Engine Oil pump cover
plate screwsSTC 50552
KV6 Engine Camshaft carrier to
cylinder headSTC 4600
KV6 Engine Sump to lower
crankcaseSTC 4600
KV6 Engine Oil pick-up strainer
boltSTC 50552
KV6 Engine Lower crankcase to
cylinder blockSTC 50550
KV6 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Coolant stub pipe to
cylinder blockSTC 50554
Engine
Management
System -
MEMSSensor - Engine
Coolant
temperature (ECT)STC 50552
Cooling
System - KV6Cylinder block drain
plugSTC 50552
Manual
Gearbox - PG12 top bolts -
gearbox to engineSTC 50552
Manual
Gearbox -
GetragRear cover to
gearcaseSTC 4600
Manual
Gearbox -
GetragGearshift cover STC 4600
Intermediate
Reduction
DriveEnd cover gasket -
IRD housingSTC 4600
Automatic
Gearbox -
JatcoFluid pan to
gearcaseSTC 4600
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811

MAINTENANCE
MAINTENANCE 10-1
MAINTENANCE MAINTENANCE
Td4 - Diesel Engine - Under Bonnet View
LHD shown, RHD similar - 03 MY illustrated
1Power steering reservoir
2Cooling system expansion tank filler cap
3Engine oil filler cap
4Brake/Clutch fluid reservoir cap
5Engine Control Module box
6Engine compartment fusebox
7Battery
8Engine oil dipstick
9Windscreen washer reservoir filler cap

MAINTENANCE
10-2 MAINTENANCE
K1.8 – Petrol Engine – Under Bonnet
View
LHD shown, RHD similar
1Cooling system expansion tank filler cap
2Engine oil dipstick
3Brake/Clutch fluid reservoir cap
4Engine Control Module box
5Engine compartment fusebox
6Battery
7Air cleaner
8Engine oil filler cap
9Windscreen washer reservoir filler cap
10Power steering reservoir

MAINTENANCE
MAINTENANCE 10-3
KV6 – Petrol Engine – Under Bonnet
View
LHD shown, RHD similar - 03 Model Year illustrated
1Power steering reservoir
2Cooling system expansion tank filler cap
3Brake/Clutch fluid reservoir cap
4Engine Control Module box
5Engine compartment fusebox
6Battery
7Engine oil filler cap
8Engine oil dipstick
9Windscreen washer reservoir filler cap