CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.
CHARGING AND STARTING
REPAIRS 86-1-11
Tensioner - ancillary drive belt - Td4
$% 86.10.06
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove hydramount.
+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
4.Remove ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Remove bolt securing dipstick tube to oil filter.
6.Move dipstick tube aside for access.
7.Remove alternator.
+ CHARGING AND STARTING,
REPAIRS, Alternator - Td4.
8.Manoeuvre engine to suitable working height.9.Remove Allen bolt securing ancillary belt idler
and remove idler from vehicle.
10.Remove nut, securing ancillary drive belt
tensioner arm to rear of spring housing.
11.Rotate belt tensioner arm through 180° to clear
chassis side member and remove from timing
cover.
M86 5302
M86 5303
CHARGING AND STARTING
86-1-12 REPAIRS
12.Remove and discard tensioner arm seal.
13.Remove 2 bolts from timing cover, securing
ancillary drive belt tensioner.
14.Remove tensioner.
Refit
1.Clean tensioner block and mounting.
2.Position tensioner block, temporarily fit
tensioner arm to align spring block with timing
cover. Fit bolts and tighten to 25 Nm (18 lbf.ft).
Remove tensioner arm.
3.Clean seal mounting for tensioner arm on
timing cover, fit new seal.
4.Fit ancillary drive belt tensioner arm to timing
cover, turn through 180° to align with tensioner
spring housing, push fully home. Fit and tighten
nut to 10 Nm (7.5 lbf.ft).
5.Fit alternator.
+ CHARGING AND STARTING,
REPAIRS, Alternator - Td4.
6.Fit idler pulley to mounting and tighten Allen
bolt to 25 Nm (18 lbf.ft).
7.Position dipstick tube to oil filter, fit bolt and
tighten to 10 Nm (7.5 lbf.ft).
8.Fit ancillary drive belt.
+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
9.Fit hydramount.
+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
11.Connect battery earth lead.
Battery
$% 86.15.01
Remove
1.Disconnect both battery terminals, earth lead
first.
2.Remove bolt and battery clamp.
3.Remove battery.
Refit
1.Clean battery tray.
2.Fit battery and clamp, tighten bolt to 12 Nm (9
lbf.ft).
3.Apply petroleum jelly to both terminals, fit and
tighten terminal bolts negative lead last.
