2001 LAND ROVER FREELANDER engine oil

ENGINE MANAGEMENT SYSTEM - SIEMENS
18-3-12 REPAIRS
Sensor - camshaft position (CMP)
$% 18.30.24
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Release CMP multiplug from bracket and
disconnect multiplug.
4.Remove bolt securing CMP sensor multiplug
bracket and release CMP sensor lead from
behind bracket.
5.Remove bolt securing CMP sensor to camshaft
cover.
6.Remove CMP sensor and discard seal.Refit
1.Clean CMP sensor and mating face.
2.Lubricate new seal with clean engine oil and fit
to CMP sensor.
3.Position CMP sensor, fit and tighten bolt to 8
Nm (6 lbf.ft).
4.Feed CMP sensor lead behind multiplug
bracket, align bracket, fit bolt and tighten to 8
Nm (6 lbf.ft).
5.Connect CMP sensor multiplug and secure to
bracket.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-3
Fuel system - depressurise - KV6 - NAS
$% 19.50.02
Check
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
3.Remove schraeder valve cap.
4.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.5.Connect adapter LRT-19-006 to schraeder
valve.
6.Position opposite end of adapter LRT-19-006
into container, turn tap to release pressure.
7.Remove adapter LRT-19-006 from schraeder
valve.
8.Fit cap to schraeder valve.
9. Up to 03MY: Fit and tighten nut and bolt
securing coil.
10.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-5
Fuel system - pressure test - KV6 - NAS
$% 19.50.13
Remove
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth beneath fuel rail.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
4.Connect adaptor LRT-19-006, to pressure
gauge LRT-19-004 .
5.Remove schraeder valve cap.
6.Connect pressure gauge to fuel rail schraeder
valve.
7.Start engine. Pressure at idle = 3.4 bar. If
pressure is below 3.4 bar, suspect the following
in order: fuel hoses, filter, regulator and pump.
Refit
1.Stop engine.
2.Disconnect pressure gauge LRT-19-006 and
adapter LRT-19-004 from fuel rail.
3. Up to 03MY: Fit and tighten nut and bolt
securing coil.
4.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
Fuel system - pressure test - K1.8
$% 19.50.13
Check
1.Disconnect battery earth lead.
2.Position absorbent cloth beneath fuel pipe to
catch spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
3.Disconnect fuel pipe from inlet manifold.
4.Connect LRT-19-004A to manifold and fuel
pipe.
Note:: LRT-19-004X can be used as an
alternative.
5.Connect battery earth lead.
6.Start engine. Pressure at idle = 3.6 bar ± 0.2
bar.
7.Stop engine. If pressure is out of tolerance
suspect the following in order: fuel hoses, filter
and pump.
8.Remove plug, reconnect vacuum hose and
secure hose with clip.
9.Disconnect battery earth lead.
10.Disconnect LRT-19-004A from fuel pipe and
inlet manifold.
11.Connect fuel pipe to manifold.
12.Connect battery earth lead.
LRT - 19 -004A
M19 3675

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-39
Injectors - set - K1.8
$% 19.60.12
Remove
1.Disconnect battery earth lead.
2.Release clip and disconnect vacuum pipe from
fuel pressure regulator.
3.Remove engine oil dipstick.
4.Position absorbent cloth beneath fuel rail.
5.Release fuel feed hose from fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.6.Remove 2 bolts securing fuel rail to inlet
manifold.
7.Release fuel rail and injectors from inlet
manifold.
8.Release and remove injector spacer.
9.Disconnect multiplug from injectors.
10.Remove the fuel rail complete with injectors.
11.Release spring clips securing injectors to fuel
rail and remove fuel injectors.
12.Remove and discard 2 'O' rings from each
injector.
13.Fit protective caps to each end of injectors.

FUEL DELIVERY SYSTEM - PETROL
19-2-40 REPAIRS
Refit
1.Remove protective caps from each injector.
2.Clean injectors and recesses in fuel rail and
inlet manifold.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injectors to fuel rail and secure with spring
clips.
5.Position fuel rail assembly and connect injector
multiplugs.
6.Fit injector spacer.
7.Push each injector into inlet manifold.
8.Fit bolts securing fuel rail to inlet manifold and
tighten to 8 Nm ( 6 lbf.ft).
9.Connect fuel feed hose to fuel rail.
10.Fit engine oil dipstick.
11.Connect vacuum pipe to fuel pressure regulator
and secure with clip.
12.Connect battery earth lead.
Actuator unit - cruise control - KV6 - non
NAS
$% 19.75.05
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Disconnect vacuum hose from actuator.
4.Remove nut securing actuator to mounting
bracket.
5.Release operating rod from throttle cam and
remove actuator.
Refit
1.Position actuator and connect operating rod to
throttle cam.
2.Position actuator into mounting bracket, fit and
tighten nut.
3.Connect vacuum hose to actuator.
4.Check pull rod to retainer clearance, with lever
fully returned, pull rod should just be held by
retainer.
5.Release retainer by turning anti-clockwise,
eliminate clearance then rotate retainer half
turn clockwise. Check pull rod is just held and
rotate retainer a further quarter turn clockwise
to lock.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
REPAIRS 30-3-17
30.Remove and discard seals from inlet manifold
chamber and 'O' rings from RH inlet manifold.Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Connect multiplugs to plug top coils and secure
with locking clips.
5.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
6.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7.5 lbf.ft).
7.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
8.Connect multiplugs to VIS motors.
9. NAS models: Connect engine breather pipe.
10. NAS models: Connect multiplugs to IAT and
MAF sensors.
11.Connect brake servo vacuum hose to inlet
manifold chamber.
12.Connect vacuum/breather hoses to LH and RH
camshaft covers and to throttle body.
13.Connect cruise control actuator vacuum pipe.
14. Non NAS models: Connect vacuum hose to
IACV housing.
15. Non NAS models: Connect multiplugs to TP
and IACV sensors.
16.Connect vacuum/breather hoses to LH
camshaft cover, 'T' piece and purge control
valve.
17. Non NAS models: Connect small vacuum
hose to purge control valve.
18.Connect multiplug to purge control valve .
19.Connect EVAP hose to purge control valve.
20.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
21.Remove absorbent cloth.
22. Non NAS models: Connect throttle inner cable
to throttle cam and secure outer cable in
abutment bracket.
23. Non NAS models: Secure throttle cable in
clips on harness brackets.
24.Adjust throttle cable, if fitted.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
25.Remove vacuum enhancer.

+ BRAKES, REPAIRS, Vacuum -
enhancer - KV6.
26.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-22 REPAIRS
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to inlet manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
5.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7 lbf.ft).
6.Connect multiplugs to plug top coils and secure
with locking clips.
7.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
8.Connect multiplugs to VIS motors.
9. NAS models: Align harness and fuel feed pipe.
Secure harness and pipe in clip on manifold
chamber.
10. NAS models: Using a new clip, fit intake hose
to throttle body and secure hose with clip.
11. NAS models: Connect multiplug to throttle
body.
12. NAS models: Connect multiplugs to IAT and
MAF sensors.
13. NAS models: Fit vacuum/breather pipe and
connect to LH camshaft cover, RH camshaft
cover link pipe and inlet manifold chamber.
14. NAS models: Using a new clip, fit vacuum/
breather pipe to engine air intake hose and
secure pipe with clip.
15. NAS models: Connect vacuum/breather pipe
to LH and RH camshaft covers. Fit pipe into
clip.16. Non NAS models: Connect cruise control
actuator vacuum pipe.
17. Non NAS models: Fit vacuum/breather pipe to
throttle body and connect pipe to LH and RH
camshaft covers.
18. Non NAS models: Fit vacuum/breather pipe to
purge control valve and LH camshaft cover.
Using a new clip, connect pipe to 'T' piece and
secure pipe with clip.
19. Non NAS models: Connect multiplug to TP
sensor.
20. Non NAS models: Connect multiplug to IACV.
21. Non NAS models: Connect vacuum pipe to
IACV.
22. Non NAS models: Connect small vacuum pipe
to purge control valve.
23.Connect multiplug to purge control valve .
24.Connect EVAP hose to purge control valve.
25.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
26. Non NAS models: Connect throttle inner cable
to throttle cam and secure outer cable in
abutment bracket.
27. Non NAS models: Secure throttle cable in
clips on harness brackets.
28. Non NAS models: Adjust throttle cable.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
29.Fit vacuum enhancer.

+ BRAKES, REPAIRS, Vacuum -
enhancer - KV6.
30.Connect the battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-26 OVERHAUL
11.Release 2 clips securing RH plug top coil
harness to inlet manifold camber rear support
brackets.
12.Remove 4 bolts securing inlet manifold
chamber to LH inlet manifold.
13.Release and raise inlet manifold chamber from
inlet manifolds.
14.Remove inlet manifold chamber.15.Remove and discard seals from inlet manifold
chamber and 'O' rings from RH inlet manifold.
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to manifold chamber.
3.Position inlet manifold chamber, secure RH coil
harness clips in inlet manifold chamber support
brackets.
4.Align inlet manifold chamber to inlet manifolds,
fit and tighten bolts to 18 Nm (13 lbf.ft).
5.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7.5 lbf.ft).
6.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
7.Connect multiplugs to VIS motors.
8.Connect vacuum/breather hoses to LH and RH
camshaft covers and to throttle body.
9.Connect vacuum hose to IACV housing.
10.Connect multiplugs to TP and IACV sensors.
11.Connect vacuum/breather hoses to LH
camshaft cover, 'T' piece and purge control
valve.
12.Connect small vacuum hose to purge control
valve.
13.Connect multiplug to purge control valve .