2001 LAND ROVER FREELANDER display

CONTENTS
22 CONTENTS
NAVIGATION SYSTEM ............................................................................ 87-1
REPAIRS
Interface unit - remote control ........................................................................................................ 87-1
Display unit - navigation system .................................................................................................... 87-1
INSTRUMENTS ......................................................................................... 88-1
REPAIRS
Clock .............................................................................................................................................. 88-1
Instrument panel - up to 04MY ....................................................................................................... 88-2
Instrument panel - from 04MY ........................................................................................................ 88-3
Cowl - instrument - up to 04MY ...................................................................................................... 88-4
Cowl - instrument - from 04MY ....................................................................................................... 88-5
Sender unit - fuel tank gauge.......................................................................................................... 88-6
Sender unit assembly - fuel tank - Td4 models - from 03MY.......................................................... 88-6

INTRODUCTION
01-4
HRW Heated Rear Window
ht/HT High tension
HSLA High Strength Low Alloy
IACV Idle Air Control Valve
IAT Intake Air Temperature
ICE In-Car Entertainment
i.dia. Internal diameter
IDM Intelligent Driver Module
IF Intermediate Frequency
in Inch
in
2Square inch
in3Cubic inch
ILT Inlet Throttle
ISO International Organisation for
Standardisation
ITS Inflatable Tubular Structure
k Thousand
kg Kilogramme
kg/h Kilogrammes per hour
km Kilometre
km/h Kilometres per hour
kPa KiloPascal
KS Knock Sensor
lLitre
lb(s) Pounds
lbf Pounds force
lbf.in Pounds force inches
lbf/in
2Pounds per square inch
lbf.ft Pounds force feet
λLambda
lc Low compression
LCD Liquid Crystal Display
LED Light Emitting Diode
LEV Low Emission Vehicle
LH Left-Hand
LHD Left-Hand Drive
LSM Light Switch Module
LVS Liquid Vapour Separator
mMetre
µMicro
MAF Mass Air Flow
MAP Manifold Absolute Pressure
MFU Multi-Function Unit
MFL Multi-Function Logic
max. Maximum
MEMS Modular Engine Management
System
MIG Metal/Inert Gas
MIL Malfunction Indicator Lamp
MPa MegaPascal
MOSFET Metal Oxide Semiconductor Field
Effect Transistor
min. Minimum
- Minus (tolerance)
' Minute (angle)
mm Millimetre
mph Miles per hour MPi Multi-Point injection
MV Motorised Valve
MY Model Year
NAS North American Specification
(-) Negative (electrical)
Nm Newton metre
No. Number
NO
2Nitrogen Dioxide
NO
xOxides of Nitrogen
NTC Negative Temperature
Coefficient
NRV Non Return Valve
OBD On Board Diagnostics
OBM On Board Monitoring
o.dia. Outside diameter
OAT Organic Acid Technology
ORM Off-road Mode
ΩOhm
PAS Power Assisted Steering
PCB Printed Circuit Board
PCV Positive Crankcase Ventilation
PDC Parking Distance Control
PDOP Position Dilation Of Precision
PI Programme Information
PPS Pulse Per Second
PS Programme Service
psi Pounds per square inch
pts. Pints
% Percentage
+ Plus (tolerance) or Positive
(electrical)
±Plus or minus (tolerance)
PTC Positive Temperature Coefficient
PTFE Polytetrafluorethylene
PWM Pulse Width Modulation
RDS Radio Data Service
rRadius
:Ratio
ref Reference
REG Regionalisation
RES Rover Engineering Standards
rev/min Revolutions per minute
RF Radio Frequency
RGB Red / Green / Blue
RH Right-Hand
RHD Right-Hand Drive
ROM Read Only Memory
RON Research Octane Number
ROV Roll Over Valve
ROW Rest Of World
SAE Society of Automotive Engineers
SAI Secondary Air Injection
" Second (angle)
SLABS Self Levelling and Anti-Lock
Brake System
SLS Self Levelling Suspension
SOHC Single Overhead Camshaft
SPE Single Point Entry

GENERAL INFORMATION
03-25
Warning Labels
Warning symbols are displayed at various positions
in the vehicle (either in a suitable prominent position
such as driver and passenger side glass, or attached
to the component itself) to indicate SRS items which
must be treated with particular care. These include:
A - The need for caution when working in close
proximity to SRS components.
B - Refer to the publication where the procedures,
instructions and advice can be found (usually
Workshop Manual or Owner's Handbook) for
working on the SRS system.
C - Do not use rear facing child seats in the front
passenger seat if the vehicle is fitted with a
passenger airbag.Driver and Passenger Side Windows
WARNING: It is imperative that before any work
is undertaken on the SRS system the appropriate
information is read thoroughly.
Caution labels are attached to SRS system
components and may also be applied to vehicle trim
close to SRS components and harnesses. The driver
and front passenger airbag modules have an 'SRS
AIRBAG' symbol moulded into the module's plastic
trim to identify the presence of airbags. Other SRS
warning labels include:
End of Fascia
Label located on end of fascia; warning not to use
rear facing child seats in the front passenger seat in
vehicles fitted with a front passenger airbag.

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-9
Selector indicator - from 04MY
$% 44.15.10
Remove
1.Position gear selector lever in 'Neutral' and
remove gear selector knob.
WARNING: Gear knob will be released
suddenly, keep face clear of gear knob
during removal.
2.Working from forward edge, carefully release
spring clip securing gear selector indicator
assembly to centre console. Release 2
additional clips at the sides and slide assembly
forward.3.Disconnect multiplug from hill descent switch.
4.Disconnect multiplug from gear selector
indicator module.
5.Remove gear selector indicator assembly.
Refit
1.Position gear selector indicator assembly to
centre console.
2.Connect 2 multiplugs.
3.Ensure LED display module is located on pegs.
4.Fit and secure gear selector indicator assembly
to centre console.
5.Fit gear selector knob.
CAUTION: Selector lever must be in 'Park'
before fitting knob, failure to comply may
result in damage to selector assembly.
M44 1992
M44 1993

NAVIGATION SYSTEM
REPAIRS 87-1
NAVIGATION SYST EM REPAIRS
Interface unit - remote control
$% 86.53.15
Remove
1.Remove front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
2.Release interface ECU from bracket,
disconnect multiplug and remove ECU.
Refit
1.Secure interface ECU in bracket and connect
multiplug.
2.Fit front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
Display unit - navigation system
$% 86.53.20
Remove
1.Fit tool LRT-86-009 into slots, ensuring correct
handed tool is in correct slot.
The tools are stamped with 'TOP L' and 'TOP
R', ensure the stampings are facing upwards
when removing the unit.
2.Pull unit from fascia.
3.Disconnect 3 multiplugs and 2 coax cables,
remove unit.
4.Push retaining clips inwards and remove keys.
Refit
1.Position unit to fascia, connect multiplugs and
coax cables.
2.Slide unit in fascia until retaining clips engage.
3.Enter security code, check system is
operational.
M86 5745
M86 5741