2001 LAND ROVER FREELANDER roof

TORQUE WRENCH SETTINGS
06-30
Body
TORQUE DESCRIPTION METRIC IMPERIAL
Doors
Door lock striker to body screws 10 Nm 7 lbf.ft
Door stiffener Torx screws 9 Nm 7 lbf.ft
Front door control unit to glass clamp bolts 9 Nm 7 lbf.ft
Front door hinge bolts 30 Nm 22 lbf.ft
Rear door glass clamp bolts 8 Nm 6 lbf.ft
Tail door exterior handle nuts 5 Nm 3.7 lbf.ft
Tail door glass clamp bolts 8 Nm 6 lbf.ft
Tail door glass regulator lock nuts 14 Nm 10 lbf.ft
Tail door hinge bolts 30 Nm 22 lbf.ft
Exterior Fittings
Bonnet hinge, bolts 9 Nm 6.5 lbf.ft
Bonnet release lever to 'A' post bolt 9 Nm 6.5 lbf.ft
Exterior mirror to door Torx screws 6 Nm 4.4 lbf.ft
Front wing bolts5 Nm 3.7 lbf.ft
Spare wheel mounting bracket:
⇒ Bolts13 Nm 10 lbf.ft
⇒ Nuts25 Nm 18 lbf.ft
Spare wheel to bracket retention nuts 45 Nm 33 lbf.ft
Splash shield bolts 10 Nm 7 lbf.ft
Underbelly panel to body bolts 45 Nm 33 lbf.ft
Underbelly panel to body rear screws 8 Nm 6 lbf.ft
3 door vehicles
Hard back catch Torx screws 10 Nm 7.5 lbf.ft
Hard back retainer Torx screws 10 Nm 7.5 lbf.ft
Soft back support bracket bolts 25 Nm 18 lbf.ft
5 door vehicles
Roof rack side rail bolts 22 Nm 16 lbf.ft
Interior Trim Components
Engine compartment fusebox bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox mounting plate to body and steering column
bracket bolts8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Seats
Front seat runner to body bolts 45 Nm 33 lbf.ft
Front seat squab frame to cushion frame Torx bolts 45 Nm 33 lbf.ft
Rear bench seat to body bolts 25 Nm 18 lbf.ft
Rear seat cushion to squab Torx bolts 28 Nm 21 lbf.ft
Rear seat catch assembly Torx bolts 32 Nm 24 lbf.ft
Rear seat squab lock Torx screws 20 Nm 15 lbf.ft
Rear seat squab to cushion Torx bolts 28 Nm 21 lbf.ft
Rear seat hinge Torx bolts 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-31
Seat belts (3-door models)
Front seat belt loop to 'B' post bolt 31 Nm 23 lbf.ft
Front seat belt pre-tensioner and buckle to seat frame Torx bolt 32 Nm 24 lbf.ft
Front seat belt reel bolt 31 Nm 23 lbf.ft
Front seat belt slider bar bolts 40 Nm 30 lbf.ft
Front seat belt lower mounting Torx bolts 40 Nm 30 lbf.ft
Front seat belt upper mounting Torx bolt 31 Nm 23 lbf.ft
Rear seat belt and buckle to frame Torx bolts 32 Nm 24 lbf.ft
Rear seat belt lower fixing to body bolt 50 Nm 37 lbf.ft
Rear seat belt reel to squab nut 32 Nm 24 lbf.ft
Rear seat belt upper mounting bolt 32 Nm 24 lbf.ft
Rear seat squab lock Torx screws 20 Nm 15 lbf.ft
Seat belt pre-tensioner to seat bolt 32 Nm 24 lbf.ft
Seat belts (5-door models)
Front seat belt adjuster to 'B' post Torx bolts 26 Nm 19 lbf.ft
Front seat belt upper anchorage to adjuster mounting nut 31 Nm 23 lbf.ft
Front seat belt lower fixing to 'B' post bolt 40 Nm 30 lbf.ft
Front seat belt pre-tensioner and buckle to seat frame Torx bolt 32 Nm 24 lbf.ft
Front seat belt reel bolt 31 Nm 23 lbf.ft
Rear centre seat belt reel to seat squab nut 32 Nm 24 lbf.ft
Rear seat belt and buckle bolts 32 Nm 24 lbf.ft
Rear side seat belt lower fixing bolt 40 Nm 30 lbf.ft
Rear side seat belt reel bolt 50 Nm 37 lbf.ft
Rear side seat belt buckle to catch assembly bolt 32 Nm 24 lbf.ft
Rear side seat belt upper mounting bolt 32 Nm 24 lbf.ft
Seat belt height adjuster bolts 26 Nm 19 lbf.ft
Screens
Sun roof side rail Torx bolts 22 Nm 16 lbf.ft TORQUE DESCRIPTION METRIC IMPERIAL

MAINTENANCE
MAINTENANCE 10-11
Door Locks, Hinges, Check Straps and
Bonnet Catch
Check
1.Check operation of each door, door lock,
bonnet catch and fuel filler flap.Lubricate Front and Rear Doors
1.Open each door in turn and lubricate door
hinges and check strap using recommended
lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
2.Lubricate door lock, striker and private lock
using PTFE lubricant. Remove excessive
lubricant, particularly from door striker area, to
avoid customer complaint.
3.Check tightness of accessible door lock and
striker fixings.
4.Open and close door to check for smooth,
noise-free operation. Ensure door closes
securely.
5.Check for smooth operation of private lock.
Lubricate Tail Door
1.Open tail door and lubricate hinges using
recommended lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
2.Grease tail door check slide.
3.Lubricate rear door lock and striker using PTFE
lubricant. Remove excessive lubricant to avoid
customer complaint, particularly from door
striker area.
4.Check tightness of accessible tail door lock and
striker fixings.
Lubricate Bonnet
1.With bonnet open, lubricate hinges, striker, lock
and safety catch using a suitable lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
Sunroof Guide Rails, Slides and Seal
1.With sunroof open, lubricate accessible guide
rails, slides and seals. Remove any excess
lubricant to avoid contaminating roof lining and
trim.
2.Ensure sunroof closes correctly.
Sunroof Drain Tubes and Channels
1.Remove any debris from sunroof tray.
2.Ensure that all accessible sunroof drain tubes
are clear using a low pressure air line.

FUEL DELIVERY SYSTEM - PETROL
19-2-30 REPAIRS
Tank - Non NAS
$% 19.55.01
Remove
1.Position vehicle on ramp.
2.Disconnect battery earth lead.
3.Remove fuel pump assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Pump - fuel.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
4.Using a fuel recovery appliance, drain the fuel
from the tank into a sealed container. Follow
the manufacturer's instructions for the
connection and safe use of the appliance.
WARNING: The fuel tank must be drained
before it is removed from the vehicle.
5.Remove intermediate exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Exhaust pipe -
intermediate.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Intermediate
pipe - Non NAS.
6.Remove propeller shaft.

+ DRIVESHAFTS, REPAIRS, Propeller
shaft assembly.
7.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
8.Release clip from breather hose and
disconnect breather hose from filler neck.
9.Release clip and disconnect vent hose from
fuel tank on vapour separator.10.Remove tamper proof cover from filler hose clip
and loosen clip.
11.Support weight of rear subframe and remove 4
bolts securing subframe to body.
12.Lower subframe.
CAUTION: Do not allow sub frame to hang
on rear brake hoses.

FUEL DELIVERY SYSTEM - PETROL
19-2-32 REPAIRS
Tank - NAS
$% 19.55.01
Remove
1.Position vehicle on ramp.
2.Disconnect battery earth lead.
3.Using a fuel recovery appliance, drain the fuel
from the tank into a sealed container. Follow
the manufacturer's instructions for the
connection and safe use of the appliance.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Fuel tank - drain.
WARNING: The fuel tank must be drained
before it is removed from the vehicle.
4.Remove intermediate exhaust pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Intermediate
pipe - NAS.
5.Remove propeller shaft.

+ DRIVESHAFTS, REPAIRS, Propeller
shaft assembly.
6.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
7.Remove tamper proof cover from filler hose clip
and loosen clip.8.Support weight of rear subframe and remove 4
bolts securing subframe to body.
9.Lower subframe.
CAUTION: Do not allow sub frame to hang
on rear brake hoses.
10.With assistance, remove 4 bolts securing fuel
tank to body and remove tank.
NOTE: Pull vent and breather hoses through
body while lowering fuel tank.

FUEL DELIVERY SYSTEM - PETROL
19-2-34 REPAIRS
Filler neck
$% 19.55.07
Remove
1.Disconnect battery earth lead.
2.Ensure fuel tank is less than half full. If not,
drain fuel tank to less than half full.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Fuel tank - drain.
3.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
4.Remove fuel filler cap.
CAUTION: Before disconnecting any part of
the fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign
matter into fuel system.
5.Unclip escutcheon from fuel filler neck.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
6.Remove 3 nuts securing fuel filler neck to body.7.Release clip from breather hose and
disconnect breather hose from filler neck.
8.Release fuel tank vent pipe from filler neck.
9.Disconnect Lucar connector from fuel filler
neck.
10.Remove bolt securing filler neck to body.
11.Remove tamper proof cover from filler hose clip
and loosen clip.
12.Disconnect hose from filler neck and remove
filler neck assembly.
Refit
1.Position filler neck assembly, connect to hose,
secure clip and fit tamper proof cover.
2.Fit bolt securing filler neck to body and tighten
to 9 Nm (7 lbf.ft).
3.Connect Lucar connector to fuel filler neck.
4.Position fuel tank vent pipe around filler neck.
5.Connect breather hose to filler neck, fit and
secure clip.
6.Fit nuts securing fuel filler neck to body and
tighten to 9 Nm (7 lbf.ft).
7.Clip escutcheon to fuel filler neck.
8.Fit fuel filler cap.
9.Fit RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
10.Connect battery earth lead.
M19 3230

EXTERIOR FITTINGS
REPAIRS 76-2-7
Side rail - integral roof rack - 5 door
$% 76.11.30
Remove
1.Remove finishers from feet of side rail.
2.Remove 4 Torx screws securing side rail to roof
panel.
3.Remove side rail and 2 gaskets.
NOTE: Do not carry out further dismantling if
component is removed for access only.
4.Remove seal from each torque bolt.
5.Remove Torx bolts from side rail.
Refit
1.Fit Torx bolts and seals to replacement side rail.
2.Fit gaskets to side rail.
3.Position side rail and tighten Torx bolts to 22
Nm (16 lbf.ft).
4.Fit finishers to feet of side rail.
Bonnet
$% 76.16.01.99
Remove
1.Support bonnet in open position.
2.Fit protection covers to wings and mark hinge
outline on bonnet if bonnet is to be refitted.
3.Disconnect windscreen washer tube at elbow
joint.
4.With assistance, remove bolts securing hinges
to bonnet and remove bonnet.
Refit
1.With assistance, position bonnet to hinges. Fit
and lightly tighten bolts.
2.Connect windscreen washer tube.
3.Close bonnet. Check that bonnet is aligned to
both front wings and that gaps are equal. If
necessary, adjust bonnet alignment and/or
gaps.
4.Finally tighten hinge bolts to 9 Nm (7 lbf.ft).

EXTERIOR FITTINGS
REPAIRS 76-2-17
Moulding - roof - 5 door
$% 76.43.68
Remove
1.Remove tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
2.Remove roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
3.Using a suitable hooked tool in the front foot
hole of the roof finisher, slide the finishers 2
forward clips rearward from the roof channel.
4.Slide the clip rear of the foot hole forward from
the roof channel.
5.Slide the remaining 7 clips from the roof
channel.
6.Remove nut securing rear end of roof finisher
and remove finisher.
7.Remove clips from roof finisher.Refit
1.Fit clips to roof finisher.
2.Fit finisher to roof channel with forward 2 clips.
3.Slide finisher to align with screen. Feed forward
clip below screen seal.
4.Fit remaining clips to roof channel.
5.Fit nut and secure rear end of finisher.
6.Ensure full length of finisher is correctly seated
in roof channel.
7.Fit roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
8.Fit tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.