2001 LAND ROVER FREELANDER door lock

FUEL DELIVERY SYSTEM - PETROL
REPAIRS 19-2-29
Pump - fuel
$% 19.45.08
WARNING: If fuel tank is full, using a fuel
recovery appliance, drain excess fuel from fuel
filler neck until a level below height of fuel pump
is obtained.
Remove
1.Disconnect battery earth lead.
2.Open RH rear and tail doors.
3.Fold RH rear seat forward.
4.Remove 2 fasteners securing front and rear
carpets.
5.Pull back loadspace carpet from fuel pump
access panel.
6.Remove 6 screws securing access panel.
WARNING: Depressurise the system before
disconnecting any components. Fuel
pressure will be present in the system even
if the ignition has been switched off for
some time.
7.Remove access panel.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
8.Disconnect multiplug and fuel hose from fuel
pump housing.
CAUTION: Always fit plugs to open
connections to prevent contamination.9.Use LRT-19-009 to remove locking ring from
fuel pump housing.
10.Remove fuel pump housing and discard sealing
ring.
Refit
1.Clean fuel pump housing and mating face on
fuel tank.
2.Fit new seal to fuel pump housing.
3.Fit fuel pump housing to fuel tank, fit and tighten
locking ring to 35 Nm (26 lbf.ft) using LRT-19-
009.
4.Connect multiplug and fuel hose to fuel pump
housing.
5.Fit access panel and secure with screws.
6.Position carpet and secure with fasteners.
7.Reposition rear seat.
8.Close rear and tail doors.
9.Connect battery earth lead.

RESTRAINT SYSTEMS
REPAIRS 75-7
Stalk - rear seat belt - LH - 5 door
$% 76.73.32
Remove
1.Fold rear seat forward.
2.Remove 3 screws from end cover and remove
cover from seat hinge.
3.Remove 4 Torx bolts from seat lock down catch
and remove catch assembly.
4.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Fit buckle to catch assembly and tighten Torx
bolt to 32 Nm (24 lbf.ft).
2.Fit catch assembly to seat and tighten Torx
bolts.
3.Fit catch assembly to seat, fit Torx bolts but do
not tighten at this stage.
4.Fold seat down and check that seat unfolds on
lock down bar correctly. Adjust catch assembly
if required.
5.Tighten catch Torx bolts to 32 Nm (24 lbf.ft).
6.Recheck seat fold.
7.Fit end cover and tighten screws.
8.Reposition rear seats.

DOORS
76-1-2 ADJUSTMENTS
Door - front - align on hinges
$% 76.28.07
Check
1.Check door for flush fit to adjacent panels and
edges for equal gaps.
Adjust
1.Open front door.
2.Place wooden block on jack and position jack to
support door under lower edge.
3.Loosen 4 bolts securing hinges to door.4.Loosen 2 Torx bolts securing door latch striker.
5.Use jack to assist with door alignment.
6.Tighten hinge bolts.
7.Remove jack and close door to check for
correct alignment.
8.When alignment is satisfactory,tighten hinge
bolts to 30 Nm (22 lbf.ft).
9.Adjust door latch striker.

+ DOORS, ADJUSTMENTS, Door -
front or rear - adjust on striker.

DOORS
76-1-10 REPAIRS
Glass - tail door
$% 76.31.20
Remove
1.Remove tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
2.Disconnect 2 Lucars from heater element.
3.Lower screen to access clamp bolts.
4.Loosen both clamp bolts, release and remove
rear screen.Refit
1.Position screen to door and align in clamps
using timing marks on screen.
2.Ensure glass is fully pushed down in clamp
closest to door hinge, then tighten clamp bolt.
3.Position screen horizontally by lifting clamp
closest to door latch so that screen heater
element is aligned with waist seal.
4.Tighten clamp bolts to 8 Nm (6 lbf.ft).
5.Raise screen and connect Lucars to screen
heater element.
6.Ensure a 5mm equal gap exists between
screen and both 'E' post finishers. If required,
adjust screen again using timing marks.
7.Loosen lower adjuster lock nuts.
8.Loosen pre-load screws so screen clears seal.
9.Adjust pre-load screws until screen is just in
contact with seal.
10.Adjust pre-load screws until screen applies a
1mm pre-load on seal.
11.Ensure there is full screen to seal contact.
12.Lower glass and tighten lock nuts to 14 Nm (10
lbf.ft).
13.Recheck pre-load.
14.Raise and lower screen to confirm correct
alignment.
15.Fit tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.

DOORS
76-1-12 REPAIRS
Glass regulator - tail door
$% 76.31.65
Remove
1.Remove rear screen.

+ DOORS, REPAIRS, Glass - tail door.
2.Disconnect multiplug from regulator motor.
3.Loosen 3 nuts securing regulator motor and
rotate motor to release from door.
4.Loosen 4 nuts securing top of cable guides and
release guides from door.
5.Remove 2 nuts securing pre-load adjusters and
rotate adjusters fully clockwise to improve
access.
6.Release regulator from door and detach
electrical harness from LH glass clamp.
7.Remove regulator from door.Refit
1.Position regulator to door and unclip motor
transit package from rail.
2.Connect multiplug to regulator motor.
3.Connect harness clip and align regulator to
door.
4.Fit nuts to pre-load adjusters, but do not tighten
at this stage.
5.Position tops of cable guides to door, leaving
fixings finger tight.
6.Tighten regulator motor fixings.
7.Fit rear screen.

+ DOORS, REPAIRS, Glass - tail door.

DOORS
REPAIRS 76-1-17
3.Remove screw securing door handle
escutcheon to door and remove escutcheon.
4.Remove cover from door pull and remove 3
screws securing door pull to door.
5.Remove screw cover for access to centre
screw and remove 5 screws securing door
pocket to door.6.Release 6 trim studs securing trim casing to
door and remove trim casing.
NOTE: Do not carry out further dismantling if
component is removed for access only.
7.Note fitted position of the long trim stud and
remove 6 trim studs from door trim casing.
8.Remove heat stakes securing door pocket to
trim casing.
NOTE: Heat stake procedure is not used on
early 04 MY vehicles.
9.Remove 4 Torx screws securing door pocket to
trim casing and remove pocket.
10.Remove foam pad from sill button guide.
11.Release retainer and remove sill button guide.
12.Release and remove locking ring securing door
pull to trim casing.
13.Remove 2 plastic rivets securing door pull to
trim casing and remove door pull.
NOTE: Plastic rivets are used for production
purposes only. Screws should be used to retain
all parts previously held in place with plastic
rivets.

DOORS
76-1-18 REPAIRS
Refit
1.Fit door pull to trim casing and secure with
screws and locking ring.
2.Fit sill button guide to trim casing and secure
with retainer.
3.Fit foam pad to sill button guide.
4.Fit door pocket to trim casing and secure with
Torx screws.
5.Fit trim studs to casing.
6.Fit trim casing to door and secure trim studs.
7.Fit screws securing door pull and fit screw
cover.
8.Fit door release handle escutcheon and secure
with screw.
9.Fit screws securing door pocket and fit screw
cover.
10.Position switch pack, connect multiplugs and
secure switch pack to trim casing.
Trim casing - rear door - up to 04MY
$% 76.34.04
Remove
1.Remove screw securing door release
escutcheon and remove escutcheon.
2.Remove 2 screws from door pull.
3.Release 10 trim studs securing trim casing to
door.
4.Disconnect multiplug and remove door trim
casing.
NOTE: Do not carry out further dismantling if
component is removed for access only.

DOORS
REPAIRS 76-1-21
8.Remove locking ring securing tweeter to trim
casing and remove tweeter.
9.Remove foam pad from sill button guide.
10.Release retainer and remove sill button guide.
11.Note the fitted position of the 2 long trim studs
and remove 9 trim studs from trim casing.
12.Release and remove locking ring securing door
pull to trim casing.
13.Remove 2 plastic rivets securing door pull to
trim casing and remove door pull.
NOTE: Plastic rivets are used for production
purposes only. Screws should be used to retain
all parts previously held in place with plastic
rivets.Refit
1.Fit door pull to trim casing and secure with
screws and locking ring.
2.Fit trim studs to casing.
3.Fit sill button guide to trim casing and secure
with retainer.
4.Fit foam pad to sill button guide.
5.Fit tweeter to trim casing and secure with
locking ring.
6.Fit and secure window lift switch and finisher to
trim casing.
7.Connect multiplugs to window lift switch and
door tweeter.
8.Position trim casing, align fasteners with holes
in door and press firmly into position.
9.Fit and tighten screws securing door pull to
door assembly.
10.Fit and secure door pull finisher to door pull.
11.Fit door release escutcheon to trim casing and
secure with screw.