2001 INFINITI QX4 clutch

SAT905A
8. After installing, check to assure that forward clutch hub rotates
clockwise.
Band Servo Piston Assembly
COMPONENTSNBAT0148
SAT161K
SAT909A
DISASSEMBLYNBAT01491. Block one oil hole in OD servo piston retainer and the center
hole in OD band servo piston.
2. Apply compressed air to the other oil hole in piston retainer to
remove OD band servo piston from retainer.
3. Remove D-ring from OD band servo piston.
SAT910A
4. Remove band servo piston assembly from servo piston
retainer by pushing it forward.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Rear Internal Gear and Forward Clutch Hub (Cont'd)
AT-333

SAT940A
d. Install band servo retainer onto transmission case.
SAT943A
4. Install rear side clutch and gear components.
a. Place transmission case in vertical position.
SAT944A
b. Slightly lift forward clutch drum assembly. Then slowly rotate it
clockwise until its hub passes fully over clutch inner race inside
transmission case.
SAT945A
c. Check to be sure that rotation direction of forward clutch
assembly is correct.
SAT946A
d. Install thrust washer onto front of overrun clutch hub.
IApply petroleum jelly to the thrust washer.
IInsert pawls of thrust washer securely into holes in over-
run clutch hub.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (1) (Cont'd)
AT-341

SAT947A
e. Install overrun clutch hub onto rear internal gear assembly.
SAT948A
f. Install needle bearing onto rear of overrun clutch hub.
IApply petroleum jelly to needle bearing.
SAT949A
g. Check that overrun clutch hub rotates as shown while holding
forward clutch hub.
SAT527G
h. Place transmission case into horizontal position.
SAT951A
i. Install rear internal gear, forward clutch hub and overrun clutch
hub as a unit onto transmission case.
ASSEMBLY
Assembly (1) (Cont'd)
AT-342

SAT757I
b. Install O-ring on revolution sensor.
IApply ATF to O-ring.
c. Install revolution sensor on adapter case.
SAT963A
d. Install adapter case gasket on transmission case.
SAT964A
e. Install parking rod on transmission case.
SAT755I
f. Install adapter case on transmission case.
SAT974A
8. Install front side clutch and gear components.
a. Install rear sun gear on transmission case.
IPay attention to its direction.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (1) (Cont'd)
AT-345

SAT967A
b. Make sure needle bearing is on front of front planetary carrier.
IApply petroleum jelly to needle bearing.
c. Make sure needle bearing is on rear of front planetary carrier.
IApply petroleum jelly to bearing.
IPay attention to its direction Ð Black side goes to front.
SAT969A
d. While rotating forward clutch drum clockwise, install front plan-
etary carrier on forward clutch drum.
SAT970A
ICheck that portion A of front planetary carrier protrudes
approximately 2 mm (0.08 in) beyond portion B of forward
clutch assembly.
SAT971A
e. Make sure bearing races are on front and rear of clutch pack.
IApply petroleum jelly to bearing races.
ISecurely engage pawls of bearing races with holes in
clutch pack.
SAT973A
f. Install clutch pack into transmission case.
ASSEMBLY
Assembly (1) (Cont'd)
AT-346

Adjustment=NBAT0156When any parts listed in the following table are replaced, total end
play or reverse clutch end play must be adjusted.
Part name Total end play Reverse clutch end play
Transmission caseII
Low one-way clutch inner raceII
Overrun clutch hubII
Rear internal gearII
Rear planetary carrierII
Rear sun gearII
Front planetary carrierII
Front sun gearII
High clutch hubII
High clutch drumII
Oil pump coverII
Reverse clutch drum ÐI
SAT975A
1. Adjust total end play.
Total end play ªT
1º:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
SAT976A
a. With needle bearing installed, place J34291-1 (bridge),
J34291-2 (legs) and the J34291-5 (gauging cylinder) onto oil
pump. The long ends of legs should be placed firmly on
machined surface of oil pump assembly. The gauging cylinder
should rest on top of the needle bearing. Lock gauging cylin-
der in place with set screw.
SAT977A
b. Install J34291-23 (gauging plunger) into gauging cylinder.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Adjustment
AT-347

SAT978A
c. Install original bearing race inside reverse clutch drum. Place
shim selecting gauge with its legs on machined surface of
transmission case (no gasket). Allow gauging plunger to rest
on bearing race. Lock gauging plunger in place with set screw.
SAT979A
d. Remove Tool and use feeler gauge to measure gap between
gauging cylinder and gauging plunger. This measurement
should give exact total end play.
Total end play ªT
1º:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
IIf end play is out of specification, decrease or increase thick-
ness of oil pump cover bearing race as necessary.
Available oil pump cover bearing race:
Refer to SDS, AT-360.
SAT980A
2. Adjust reverse clutch drum end play.
Reverse clutch drum end play ªT
2º:
0.55 - 0.90 mm (0.0217 - 0.0354 in)
SAT981A
a. Place J34291-1 (bridge), J34291-2 (legs) and J34291-5 (gaug-
ing cylinder) on machined surface of transmission case (no
gasket). Allow gauging cylinder to rest on front thrust surface
of reverse clutch drum. Lock cylinder in place with set screw.
SAT982AA
b. Install J34291-23 (gauging plunger) into gauging cylinder.
ASSEMBLY
Adjustment (Cont'd)
AT-348

SAT983A
c. Install original thrust washer on oil pump. Place shim setting
gauge legs onto machined surface of oil pump assembly. Allow
gauging plunger to rest on thrust washer. Lock plunger in place
with set screw.
SAT984A
d. Use feeler gauge to measure gap between gauging plunger
and gauging cylinder. This measurement should give you exact
reverse clutch drum end play.
Reverse clutch drum end play ªT
2º:
0.55 - 0.90 mm (0.0217 - 0.0354 in)
IIf end play is out of specification, decrease or increase thick-
ness of oil pump thrust washer as necessary.
Available oil pump thrust washer:
Refer to SDS, AT-361.
SAT985A
Assembly (2)NBAT01571. Install brake band and band strut.
a. Install band strut on brake band.
IApply petroleum jelly to band strut.
SAT986A
b. Place brake band on periphery of reverse clutch drum, and
insert band strut into end of band servo piston stem.
SAT987A
c. Install anchor end bolt on transmission case. Then, tighten
anchor end bolt just enough so that reverse clutch drum (clutch
pack) will not tilt forward.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Adjustment (Cont'd)
AT-349