2001 INFINITI QX4 clutch

SAT109B
d. Remove output shaft and parking gear as a unit from transmis-
sion case.
e. Remove parking gear from output shaft.
SAT033B
f. Remove needle bearing from transmission case.
SAT954A
23. Remove rear side clutch and gear components.
a. Remove front internal gear.
SAT110B
b. Remove bearing race from front internal gear.
SAT111B
c. Remove needle bearing from rear internal gear.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DISASSEMBLY
AT-293

SAT951A
d. Remove rear internal gear, forward clutch hub and overrun
clutch hub as a set from transmission case.
SAT148G
e. Remove needle bearing from overrun clutch hub.
f. Remove overrun clutch hub from rear internal gear and for-
ward clutch hub.
SAT036B
g. Remove thrust washer from overrun clutch hub.
SAT037B
h. Remove forward clutch assembly from transmission case.
SAT038B
24. Remove band servo and accumulator components.
a. Remove band servo retainer from transmission case.
DISASSEMBLY
AT-294

SAT194B
DISASSEMBLYNBAT01171. Remove solenoids.
a. Remove torque converter clutch solenoid valve and side plate
from lower body.
b. Remove O-ring from solenoid.
SAT667A
c. Remove line pressure solenoid valve from upper body.
d. Remove O-ring from solenoid.
SAT043G
e. Remove 3-unit solenoid assembly from upper body.
f. Remove O-rings from solenoids.
SAT195B
2. Disassemble upper and lower bodies.
a. Place upper body facedown, and remove bolts, reamer bolts
and support plates.
b. Remove lower body, separator plate as a unit from upper body.
IBe careful not to drop pilot filter, orifice check valve,
spring and steel balls.
SAT670A
c. Place lower body facedown, and remove separator plate.
d. Remove pilot filter, orifice check valve and orifice check spring.
REPAIR FOR COMPONENT PARTS
Control Valve Assembly (Cont'd)
AT-302

SAT676A
Pilot FilterNBAT0118S03ICheck to make sure that filter is not clogged or damaged.
SAT149G
Torque Converter Clutch Solenoid ValveNBAT0118S04ICheck that filter is not clogged or damaged.
IMeasure resistance. Refer to ªComponent Inspectionº, AT-152.
Line Pressure Solenoid ValveNBAT0118S05ICheck that filter is not clogged or damaged.
IMeasure resistance. Refer to ªComponent Inspectionº, AT-167.
SAT095B
3-Unit Solenoid Assembly (Overrun Clutch Solenoid
Valve and Shift Solenoid Valves A and B)
NBAT0118S06IMeasure resistance of each solenoid. Refer to ªComponent
Inspectionº, AT-171, AT-175 and AT-189.
SAT096BA
A/T Fluid Temperature Sensor and SwitchNBAT0118S07IMeasure resistance. Refer to ªComponent Inspectionº, AT-110
and AT-264.
SAT671A
ASSEMBLYNBAT01191. Install upper and lower bodies.
a. Place oil circuit of upper body face up. Install steel balls in their
proper positions.
REPAIR FOR COMPONENT PARTS
Control Valve Assembly (Cont'd)
AT-304

SAT199BA
g. Install and temporarily tighten bolts and tube brackets in their
proper locations.
Bolt length and location:
Bolt symbol a b c d
Bolt length mm (in) 70 (2.76) 50 (1.97) 33 (1.30) 27 (1.06)
SAT200B
2. Install solenoids.
a. Attach O-ring and install torque converter clutch solenoid valve
and side plates onto lower body.
SAT150G
b. Attach O-rings and install 3-unit solenoids assembly onto
upper body.
c. Attach O-ring and install line pressure solenoid valve onto
upper body.
3. Tighten all bolts.
REPAIR FOR COMPONENT PARTS
Control Valve Assembly (Cont'd)
AT-306

Reverse Clutch
COMPONENTSNBAT0128
SAT157K
SAT841A
DISASSEMBLYNBAT01291. Check operation of reverse clutch.
a. Install seal ring onto oil pump cover and install reverse clutch.
Apply compressed air to oil hole.
b. Check to see that retaining plate moves to snap ring.
c. If retaining plate does not contact snap ring,
ID-ring might be damaged.
IOil seal might be damaged.
IFluid might be leaking past piston check ball.
SAT842A
2. Remove drive plates, driven plates, retaining plate, dish plate
and snap ring.
REPAIR FOR COMPONENT PARTS
Reverse Clutch
AT-314

SAT524G
3. Remove snap ring from clutch drum while compressing clutch
springs.
IDo not expand snap ring excessively.
4. Remove spring retainer.
SAT844A
5. Install seal ring onto oil pump cover and install reverse clutch
drum. While holding piston, gradually apply compressed air to
oil hole until piston is removed.
IDo not apply compressed air abruptly.
6. Remove D-ring and oil seal from piston.
INSPECTIONNBAT0130Reverse Clutch Snap Ring and Spring RetainerNBAT0130S01ICheck for deformation, fatigue or damage.
SAT845A
Reverse Clutch Drive PlatesNBAT0130S03ICheck facing for burns, cracks or damage.
IMeasure thickness of facing.
Thickness of drive plate:
Standard value: 1.90 - 2.05 mm (0.0748 - 0.0807 in)
Wear limit: 1.80 mm (0.0709 in)
IIf not within wear limit, replace.
Reverse Clutch Dish PlateNBAT0130S04ICheck for deformation or damage.
SAT846A
Reverse Clutch PistonNBAT0130S05IShake piston to assure that balls are not seized.
IApply compressed air to check ball oil hole opposite the return
spring. Make sure there is no air leakage.
IAlso apply compressed air to oil hole on return spring side to
assure that air leaks past ball.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Reverse Clutch (Cont'd)
AT-315

SAT847A
ASSEMBLYNBAT01311. Install D-ring and oil seal on piston.
IApply ATF to both parts.
SAT848A
2. Install piston assembly by turning it slowly and evenly.
IApply ATF to inner surface of drum.
3. Install spring retainer.
SAT524G
4. Install snap ring while compressing clutch springs.
SAT850A
IDo not align snap ring gap with spring retainer stopper.
SAT842A
5. Install drive plates, driven plates, retaining plate and dish plate.
6. Install snap ring.
REPAIR FOR COMPONENT PARTS
Reverse Clutch (Cont'd)
AT-316