2001 INFINITI QX4 4WD

Diagnostic ProcedureNBTF0021
1 CHECK 2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Refer to ª2-4WD Shift Solenoid Valve and Transfer Fluid Temperature Sensorº, ªCOMPONENT INSPECTIONº, TF-111.
SMT778D
OK or NG
OK©GO TO 2.
NG©Check the following. If OK, repair or replace 2-4WD shift solenoid valve and 4WD
shift switch.
IContinuity of transfer sub-harness
Refer to ªTRANSFER TERMINAL CORD ASSEMBLY SUB-HARNESS CONNECTORº,
ªCOMPONENT INSPECTIONº, TF-114.
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure
TF-66

2 CHECK INPUT SIGNAL
With CONSULT-II
1. Select ªECU INPUT SIGNALSº in Data Monitor.
2. Read out ON/OFF status of ª2WD SWº and ªLOCK SWITCHº.
SMT974D
OK or NG
OK©1. Perform transfer control unit input/output signal inspection. Refer to ªTRANSFER
CONTROL UNIT INSPECTION TABLEº, ªTROUBLE DIAGNOSIS Ð GENERAL
DESCRIPTIONº, TF-55.
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with
harness connector.
NG©GO TO 3.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont'd)
TF-67

3 CHECK 4WD SHIFT SWITCH POWER SOURCE
1. Disconnect 4WD shift switch harness connector.
2. Turn ignition switch to ªONº position.
3. Check voltage between 4WD shift switch harness connector terminal 1 and body ground.
Voltage: Battery voltage
SMT852D
OK or NG
OK©GO TO 4.
NG©Check the following.
INo. 18 fuse (10A)
IContinuity between ignition switch and 4WD shift switch
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont'd)
TF-68

4 CHECK HARNESS CONTINUITY
1. Turn ignition switch to ªOFFº position.
2. Check continuity between the following terminals:
ITransfer control unit 9 and 4WD shift switch 2 (2WD)
ITransfer control unit 18 and 4WD shift switch 5 (4H)
ITransfer control unit 24 and 4WD shift switch 3 (AUTO)
ITransfer control unit 23 and 4WD shift switch 6 (4LO)
ITransfer control unit 1 and Transfer terminal cord assembly sub-harness connector 4
I4WD shift switch 4 and Transfer terminal cord assembly sub-harness connector 5
Continuity should exist.
SMT853D
OK or NG
OK©GO TO 5.
NG©Repair harness or connector.
5 PERFORM SELF-DIAGNOSIS AGAIN
After driving for a while, perform self-diagnosis again.
Refer to ªTrouble Diagnosis without CONSULT-IIº, TF-27.
OK or NG
OK©INSPECTION END
NG©1. Perform transfer control unit input/output signal inspection. Refer to ªTRANSFER
CONTROL UNIT INSPECTION TABLEº, ªTROUBLE DIAGNOSIS Ð GENERAL
DESCRIPTIONº, TF-55.
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with
harness connector.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont'd)
TF-69

Diagnostic ProcedureNBTF0023
1 CHECK TRANSFER FLUID TEMPERATURE SENSOR
Refer to ª2-4WD Shift Solenoid Valve and Transfer Fluid Temperature Sensorº, ªCOMPONENT INSPECTIONº, TF-111.
OK or NG
OK©GO TO 3.
NG©GO TO 2.
2 CHECK CONTINUITY
Check the following.
IContinuity of transfer sub-harness
Refer to ªTRANSFER TERMINAL CORD ASSEMBLY SUB-HARNESS CONNECTORº, ªCOMPONENT INSPECTIONº,
TF-114.
OK or NG
OK©Repair or replace fluid temperature sensor.
NG©Repair or replace transfer sub-harness.
3 CHECK INPUT SIGNAL
WITH CONSULT-II©GO TO 4.
WITHOUT CONSULT-II©GO TO 5.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TRANSFER FLUID TEMPERATURE SENSOR
Diagnostic Procedure
TF-73

5 CHECK INPUT SIGNAL
Without CONSULT-II
1. Turn ignition switch to ªOFFº position.
2. Operate 4WD shift switch and check continuity between the following terminals.
Continuity:
Terminal 40 (ATP switch) and body ground
ª4Hº position: No continuity should exist.
Between ª4Hº and ª4LOº: Continuity should exist.
ª4LOº position: No continuity should exist.
Terminal 25 (Neutral-4LO switch) and body ground
ª4Hº position: No continuity should exist.
ª4LOº position: Continuity should exist.
Terminal 43 (Wait detection switch) and body ground
ª4Hº position: No continuity should exist. (*1)
ª4LOº position: Continuity should exist.
*1: After setting from ª4LOº to ª4Hº, continuity exists while ªWaitº function is operating in ª4Hº position.
(No continuity exists when ªWaitº function is canceled.)
SMT787D
SMT849D
OK or NG
OK©GO TO 6.
NG©Check the following.
IHarness continuity between transfer switch assembly sub-harness connector and
transfer control unit
IContinuity between transfer switch assembly sub-harness connector and body ground
ATP SWITCH, WAIT DETECTION SWITCH AND NEUTRAL-4LO SWITCH
Diagnostic Procedure (Cont'd)
TF-78

Diagnostic ProcedureNBTF0025
1 CHECK MALFUNCTION
Is this malfunction detected only while driving in reverse?
YesorNo
Ye s©CHECK A/T PNP SWITCH ªRº POSITION.
Refer to AT-99, ªDTC P0705 Park/Neutral Position Switchº.
No©GO TO 2.
2 CHECK OTHER MALFUNCTION
Are other malfunctions also detected by self-diagnosis and CONSULT-II?
Refer to ªTrouble Diagnosis without CONSULT-IIº, TF-27 and ªTrouble Diagnosis with CONSULT-IIº, TF-30.
YesorNo
Ye s©CHECK FOR OTHER MALFUNCTIONS.
(When other malfunctions are eliminated, clutch pressure switch malfunction display may
disappear.)
No©GO TO 3.
3 CHECK 2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH CIRCUITS
Check 2-4WD shift solenoid valve and 4WD shift switch circuits.
OK or NG
OK©GO TO 4.
NG©Check, repair or replace faulty parts.
4 CHECK INPUT SIGNAL
WITH CONSULT-II©GO TO 5.
WITHOUT CONSULT-II©GO TO 6.
CLUTCH PRESSURE SWITCH
Diagnostic Procedure
TF-80

5 CHECK INPUT SIGNAL
With CONSULT-II
1. Turn ignition switch to ªONº position.
2. Select ªECU INPUT SIGNALSº in Data Monitor.
3. Read out ON/OFF status of ªCL PRES SWº.
SMT788D
SMT977D
OK or NG
OK©GO TO 7.
NG©Check the following.
IContinuity between transfer control unit and transfer terminal cord assembly sub-har-
ness connector
ITransfer sub-harness
IClutch pressure switch
Refer to ª4WD Solenoid Valve, Clutch Pressure Switch and Line Pressure Switchº,
ªCOMPONENT INSPECTIONº, TF-111.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CLUTCH PRESSURE SWITCH
Diagnostic Procedure (Cont'd)
TF-81