2001 HONDA ACCORD COUPE Owners Manual

HomeLink Universal Transmitter

It may be helpful to have someone
assist you with this procedure.
1. Make sure you have properly completed the "Training the
Transmitter" procedure.
2. Find the "Training" button on your garage door opener unit. The
location will vary, depending on
the manufacturer. Themanufacturer's documentation
may help.
3. Press the Training button on thegarage door opener unit until the
light next to the button comes on,
then release it. The light may blink, or come on and stay on. You then
have approximately 30 seconds to complete the following steps. 4. Press and release the button on
the HomeLink transmitter. (Thesame button you trained with the

"Training the Transmitter"

procedure.)

5. Press and release the HomeLink transmitter button again. This
should turn off the training light
on the garage door opener unit. (Some systems may require you to
press and release the button up to
three times.)
6. Press the transmitter button again. It should operate the garage door.
Instruments and Controls TRAINING BUTTON

HomeLink Universal Transmitter

Retraining a Button

To train an already programmed
transmitter button to operate a new
device:

1. Select the transmitter button you
want to train.

2. Press and hold the transmitter
button until the red light begins to

flash slowly (approximately 20
seconds).

3. While continuing to hold the
transmitter button, place the

remote control for the device 2 to5 inches from the HomeLink

transmitter.

4. Press and hold the button on the
remote control. Hold both buttons

until the red light begins to flash

rapidly.
5. Release both buttons. The
transmitter should now be trained
to operate the device.
Erasing Codes
To erase the codes stored in all three buttons, press and hold the twooutside buttons until the red light
begins to flash, then release the
buttons.
You should erase all three codes before selling the car. As required by the FCC:
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.

Changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Industry

Canada Standard RSS-210.
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference that may cause undesired operation of the device.
Instruments and Controls

Seat Adjustments

All V-6 models, and the 4-cylinder EX model with leather interior have a
power adjustable driver's seat.
The EX-V6 model also has a power adjustable passenger's seat (See
page 92 ).
The 4-cylinder EX model without leather interior has a power seat
bottom height adjustment. All otherseat adjustments in this model are
manual.

The 4-cylinder DX, LX models have
manual seat adjustments (see next
column).
The front passenger's seat in all
4-cylinder models and the LX-V6

model adjusts manually. Front Seat Adjustments

See pages 12 — 13 for important safety

information and warnings about how to

properly position seats and seat-backs.

Adjust the seat before you start
driving.
To adjust the seat forward and backward, pull up on the lever underthe seat cushion's front edge. Move
the seat to the desired position and
release the lever. Try to move theseat to make sure it is locked in

position.
To change the angle of the seat-back,
pull up on the lever on the outside of
the seat bottom. Move the seat-back
to the desired position and release
the lever. Let the seat-back latch in
the new position.
Instruments and Controls

Seat Adjustments

Driver's Seat Manual Height
Adjustment
On LX model
The height of your driver's seat is adjustable. Turn the front dial on the
outside of the seat cushion to raise
the front of the seat bottom and turn
the rear dial to raise the rear. Driver's Seat Power Height
Adjustment

On EX model without leather

The height of your driver's seat is power adjustable. Pull up on theswitch to raise the seat. Push it down
to lower the seat.
Make all adjustments before you
start driving.
Instruments and Controls

Seat Adjustments

Driver's Seat Full Power

Adjustments
On all V-6 models, and the 4-cylinder EX

model with leather interior
See pages 12 — 13 for important safety

information and warnings about how to

properly position seats and seat-backs.

The two power seat adjustment switches are on the outside edge of
the seat bottom. The horizontal switch adjusts the seat bottom in
several directions. The short vertical
switch adjusts the seat-back angle.
You can adjust the seat with the ignition switch in any position. Makeall adjustments before you start

driving.
Push the horizontal switch forward
or backward to move the seat
forward or backward. Pull up or push down on the front of
the switch to move the seat bottom's

front edge up or down. Pull up or

push down on the rear of the switch
to move the rear of the seat bottom

up or down.

Instruments and Controls

Seat Adjustments

Pull the center of the horizontal
switch up to raise the seat. Push it down to lower the seat. Adjust the seat-back angle by
pushing the rear switch in thedirection you want to move. Driver's Lumbar Support

On EX and EX V-6 models

Vary the lumbar support by moving the lever on the right side of theseat-back. Pivot the lever forward
until it stops, then let it return. Doing
this several times adjusts the lumbar support through its full range.
Instruments and Controls

Seat Adjustments

Front Passenger's Seat
Adjustments

On EX-V6 model

The seat adjustment switches are on the outside edge of the seat bottom. Push the long horizontal switch
forward or backward to move the seat bottom in that direction.
Adjust the seat-back angle by pushing the vertical switch in thedirection you want to move. Head Restraints

See page 14 for important safety
information and a warning about how to
properly position the head restraints.
The head restraints help protect you
and your passengers from whiplash
and other injuries. They are most
effective when you adjust them so
the back of the occupant's head rests against the center of the restraint. A
taller person should adjust the
restraint as high as possible.
The front head restraints adjust for height. You need both hands toadjust the restraint. Do not attempt
to adjust it while driving. To raise it,
pull upward. To lower the restraint,
push the release button sideways and push the restraint down.
To remove a head restraint for cleaning or repair, pull it up as far as
it will go. Push the release button
and pull the restraint out of the seat-

back.

Instruments and Controls
RELEASE BUTTON

Seat Adjustments

Folding Rear Seat

The back of the rear seat folds down, giving you direct access to the trunk.
The seat-back can be released from inside the car or inside the trunk.
To fold down the seat-back from inside the car, insert the master key
in the lock on the rear shelf. Turn
the key clockwise, pull down the top of the seat-back, then release the
key.
When storing cargo, you can move

the rear center shoulder belt out of
the way by removing the belt from
the guide.
To release the seat-back from inside
the trunk, pull the release loop under
the trunk panel.
To lock the seat-back upright, push it firmly against the trunk panel. Makesure it is latched in place by pulling
on the top of the seat.

CONTINUED

Instruments and Controls

MASTER KEY