2001 DODGE RAM transmission oil

UNDER VEHICLE
INSPECTION - TIRE PRESSURES
(1) Using the tire placard or the Safety Certifica-
tion Label, check that the correct tires are mounted
on the vehicle.
(2) Install valve stem extensions as required.
(3) Using the tire placard or the Safety Certifica-
tion Label, check tire pressure (including spare) and
adjust as required to recommended pressure.
(4) Inspect the spare tire for correct pressure and
proper mounting (Fig. 13).
NOTE: Tire pressure may have been set above nor-
mal during manufacturing in order to properly seat
the tire bead. Be sure to adjust to proper specifica-
tion.
INSPECTION - VISUAL
CAUTION: Before raising the vehicle on a hoist,
(Refer to LUBRICATION & MAINTENANCE/HOISTING
- STANDARD PROCEDURE) for the proper lifting
points.
(1) Visually inspect the following for loose attach-
ment, leakage, clearance and routing, and tighten
connections and clamps as required:
²Engine
²Oil Cooler
²Cooling System
²Transmission
²Driveshaft Boots²Differential
²Transfer Case (Fig. 19)
²Transmission Cooler and Lines (Fig. 18)
²Brake System and Lines (Fig. 14)
²Fuel System
²Exhaust System (Fig. 15), (Fig. 16) and (Fig. 17)
²Steering and Suspension Components
Fig. 13 SPARE TIRE INSPECTION
Fig. 14 BRAKE LINES TO CALIPERS (REAR)
Fig. 15 EXHAUST CLAMPS
30 - 8 NEW VEHICLE PREPARATIONBR/BE

ABS INDICATOR - DESCRIPTION.........8J-14
ABS INDICATOR - OPERATION..........8J-14
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-8
A/C COMPRESSOR - DESCRIPTION......24-46
A/C COMPRESSOR - DIAGNOSIS AND
TESTING...........................24-46
A/C COMPRESSOR - INSTALLATION......24-47
A/C COMPRESSOR - OPERATION........24-46
A/C COMPRESSOR - REMOVAL.........24-47
A/C COMPRESSOR CLUTCH -
DESCRIPTION.......................24-13
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-16
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-16
A/C COMPRESSOR CLUTCH -
OPERATION.........................24-13
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-14
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-13
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-13
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-17
A/C COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING.............24-17
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-18
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-17
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-18
A/C CONDENSER - DESCRIPTION........24-48
A/C CONDENSER - INSTALLATION.......24-49
A/C CONDENSER - OPERATION..........24-48
A/C CONDENSER - REMOVAL...........24-49
A/C EVAPORATOR - DESCRIPTION.......24-52
A/C EVAPORATOR - INSTALLATION......24-53
A/C EVAPORATOR - OPERATION.........24-53
A/C EVAPORATOR - REMOVAL..........24-53
A/C HEATER CONTROL - DESCRIPTION . . . 24-18
A/C HEATER CONTROL - DIAGNOSIS
AND TESTING.......................24-19
A/C HEATER CONTROL - INSTALLATION . . . 24-20
A/C HEATER CONTROL - OPERATION.....24-18
A/C HEATER CONTROL - REMOVAL......24-19
A/C HIGH PRESSURE SWITCH -
DESCRIPTION.......................24-20
A/C HIGH PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-20
A/C HIGH PRESSURE SWITCH -
INSTALLATION.......................24-21
A/C HIGH PRESSURE SWITCH -
OPERATION.........................24-20
A/C HIGH PRESSURE SWITCH -
REMOVAL..........................24-21
A/C LINE COUPLERS - DESCRIPTION.....24-40
A/C LINE COUPLERS - OPERATION......24-41
A/C LINE COUPLERS - STANDARD
PROCEDURE........................24-43
A/C LOW PRESSURE SWITCH -
DESCRIPTION.......................24-21
A/C LOW PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-21
A/C LOW PRESSURE SWITCH -
INSTALLATION.......................24-22
A/C LOW PRESSURE SWITCH -
OPERATION.........................24-21
A/C LOW PRESSURE SWITCH -
REMOVAL..........................24-21
A/C ORIFICE TUBE - DESCRIPTION.......24-53
A/C ORIFICE TUBE - OPERATION........24-53
A/C ORIFICE TUBE - REMOVAL..........24-54
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
ACCELERATOR PEDAL - INSTALLATION . . . 14-37
ACCELERATOR PEDAL - REMOVAL.......14-37
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION
...............14-91
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION
..............14-93
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION
................14-91
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL
..................14-91
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING
................7-24,7-27,7-31ACCUMULATOR - DESCRIPTION.........24-54
ACCUMULATOR - DESCRIPTION . 21-191,21-362,
21-537,21-707
ACCUMULATOR - INSPECTION . . 21-192,21-363,
21-538,21-708
ACCUMULATOR - INSTALLATION........24-55
ACCUMULATOR - OPERATION..........24-54
ACCUMULATOR - OPERATION . . . 21-191,21-362,
21-537,21-708
ACCUMULATOR - REMOVAL............24-54
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT.............................25-1
ACTUATOR - INSTALLATION, BLEND
DOOR.............................24-26
ACTUATOR - INSTALLATION, HEAT/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-71,23-80
ACTUATOR - INSTALLATION, PANEL/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-28
ACTUATOR - REMOVAL, BLEND DOOR....24-25
ACTUATOR - REMOVAL, HEAT/DEFROST
DOOR.............................24-26
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-71,
23-80
ACTUATOR - REMOVAL, PANEL/DEFROST
DOOR.............................24-27
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-27
ADAPTER - INSTALLATION, DEFROSTER
AND DEMISTER DUCT.................24-35
ADAPTER - REMOVAL, DEFROSTER AND
DEMISTER DUCT.....................24-35
ADAPTER BRACKET - INSTALLATION,
CAB CHASSIS........................13-9
ADAPTER BRACKET - REMOVAL, CAB
CHASSIS............................13-9
ADAPTER HOUSING SEAL -
INSTALLATION.................21-132,21-87
ADAPTER HOUSING SEAL - REMOVAL . . 21-132,
21-87
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-16
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-16
ADHESIVE LOCATIONS, SPECIFICATIONS
- STRUCTURAL......................23-44
ADJUSTER - DIAGNOSIS & TESTING,
POWER LUMBAR....................8N-18
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - INSTALLATION, SEAT
TRACK............................23-143
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - REMOVAL, SEAT TRACK....23-143
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM........................9-85
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM........................9-85
ADJUSTER ASSY - CLEANING, ROCKER
ARM ..............................9-262
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM.......................9-261
ADJUSTER ASSY - INSPECTION,
ROCKER ARM.......................9-262
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM.............9-142,9-200,9-263
ADJUSTER ASSY - REMOVAL, ROCKER
ARM ....................9-142,9-200,9-261
ADJUSTER KNOB - INSTALLATION,
TURNING LOOP HEIGHT...............8O-30
ADJUSTER KNOB - REMOVAL, TURNING
LOOP HEIGHT.......................8O-30
ADJUSTMENT - STANDARD
PROCEDURE, COMPASS VARIATION......8M-4
ADJUSTMENT AND VERIFICATION -
STANDARD PROCEDURE, VALVE LASH....9-256
ADJUSTMENT, BANDS . . . 21-193,21-364,21-539,
21-709
ADJUSTMENT, CABLE TENSIONER
........5-40
ADJUSTMENT, CARGO DOOR
...........23-78
ADJUSTMENT, CENTER BEARING -
CENTER BEARING
.....................3-10
ADJUSTMENT, FRONT DOOR FORE/AFT
. . . 23-68
ADJUSTMENT, FRONT DOOR IN/OUT
.....23-69ADJUSTMENT, FRONT DOOR LATCH......23-72
ADJUSTMENT, FRONT DOOR UP/DOWN . . . 23-69
ADJUSTMENT, FRONT FASCIA...........13-2
ADJUSTMENT, HOOD................23-100
ADJUSTMENT, LATCH................23-100
ADJUSTMENT, LATCH STRIKER........23-102
ADJUSTMENT, REAR BRAKE DRUM.......5-34
ADJUSTMENT, SHIFT LEVER....21-853,21-888,
21-925
ADJUSTMENT, SHIFT MECHANISM.....21-252,
21-423,21-596,21-769
ADJUSTMENTS, FOG LAMP UNIT........8L-12
ADJUSTMENTS, FRONT AXLE - 216FBI....3-17
ADJUSTMENTS, FRONT AXLE - 248FBI....3-50
ADJUSTMENTS, GEAR.................19-16
ADJUSTMENTS, HEADLAMP UNIT.......8L-21
ADJUSTMENTS, REAR AXLE - 248RBI....3-114
ADJUSTMENTS, REAR AXLE - 267RBI....3-145
ADJUSTMENTS, REAR AXLE - 286RBI....3-174
ADJUSTMENTS, REAR AXLE - 9 1/4 .......3-84
ADJUSTMENTS, TRANSMISSION
THROTTLE VALVE CABLE . 21-254,21-425,21-598,
21-771
ADJUSTMENTS, VALVE BODY . . . 21-304,21-476,
21-646,21-818
AFTER AN AIRBAG DEPLOYMENT -
STANDARD PROCEDURE, SERVICE.......8O-4
AIR BLEED - STANDARD PROCEDURE....14-57
AIR CHECKING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-147,21-318
AIR CLEANER ELEMENT - INSTALLATION . . 9-245
AIR CLEANER ELEMENT - REMOVAL.....9-244
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH.......7-77
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE
WITHOUT............................7-78
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH.............7-74
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT..........7-77
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-41
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-41
AIR COOLER AND PLUMBING -
CLEANING, CHARGE..................11-18
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE...............11-17
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-18
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE...............11-18
AIR COOLER AND PLUMBING -
OPERATION, CHARGE.................11-17
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE..................11-17
AIR DAM - INSTALLATION, FRONT........13-2
AIR DAM - REMOVAL, FRONT...........13-1
AIR EXHAUSTER - INSTALLATION.......23-77
AIR EXHAUSTER - REMOVAL...........23-77
AIR HEATER - DESCRIPTION, INTAKE....14-100
AIR HEATER - INSTALLATION, INTAKE . . . 14-101
AIR HEATER - OPERATION, INTAKE.....14-100
AIR HEATER - REMOVAL, INTAKE.......14-100
AIR HEATER RELAY - DESCRIPTION,
INTAKE............................14-101
AIR HEATER RELAY - INSTALLATION,
INTAKE............................14-102
AIR HEATER RELAY - OPERATION,
INTAKE............................14-102
AIR HEATER RELAY - REMOVAL, INTAKE . 14-102
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING...........................14-56
AIR INJECTION PUMP - DESCRIPTION....25-28
AIR INJECTION PUMP - DIAGNOSIS AND
TESTING...........................25-28
AIR INJECTION PUMP - INSTALLATION . . . 25-29
AIR INJECTION PUMP - OPERATION
.....25-28
AIR INJECTION PUMP - REMOVAL
.......25-29
AIR INJECTION SYSTEM - DESCRIPTION
. . 25-25
AIR INJECTION SYSTEM - OPERATION
....25-27
AIR INJECTION SYSTEM - TORQUE
......25-28
BR/BEINDEX 1
Description Group-Page Description Group-Page Description Group-Page

AIR PUMP FILTER - INSTALLATION......25-29
AIR PUMP FILTER - REMOVAL..........25-29
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-490,21-661
AIR TO OIL COOLER - INSTALLATION.....7-88
AIR TO OIL COOLER - REMOVAL.........7-87
AIRBAG - ASSEMBLY, DRIVER..........8O-17
AIRBAG - DESCRIPTION, DRIVER........8O-14
AIRBAG - DESCRIPTION, PASSENGER....8O-21
AIRBAG - DISASSEMBLY, DRIVER.......8O-15
AIRBAG - INSTALLATION, DRIVER.......8O-18
AIRBAG - INSTALLATION, PASSENGER . . . 8O-23
AIRBAG - OPERATION, DRIVER.........8O-14
AIRBAG - OPERATION, PASSENGER......8O-21
AIRBAG - REMOVAL, DRIVER...........8O-14
AIRBAG - REMOVAL, PASSENGER.......8O-21
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-6
AIRBAG CONTROL MODULE -
INSTALLATION.......................8O-8
AIRBAG CONTROL MODULE -
OPERATION..........................8O-6
AIRBAG CONTROL MODULE - REMOVAL . . . 8O-7
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-4
AIRBAG INDICATOR - DESCRIPTION......8J-15
AIRBAG INDICATOR - OPERATION.......8J-15
AIRBAG ON/OFF SWITCH -
DESCRIPTION, PASSENGER............8O-23
AIRBAG ON/OFF SWITCH -
INSTALLATION, PASSENGER...........8O-25
AIRBAG ON/OFF SWITCH - OPERATION,
PASSENGER........................8O-24
AIRBAG ON/OFF SWITCH - REMOVAL,
PASSENGER........................8O-24
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-4
AIRBAG SYSTEM - SPECIAL TOOLS.......8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED.............8O-4
AIRFLOW - DESCRIPTION, HVAC
SYSTEM............................24-31
AJAR SWITCH - DESCRIPTION, DOOR....8L-34
AJAR SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8L-34
AJAR SWITCH - INSTALLATION, DOOR . . . 8L-35
AJAR SWITCH - REMOVAL, DOOR.......8L-35
ALIGNMENT - DESCRIPTION, WHEEL.......2-1
ALIGNMENT - OPERATION, WHEEL........2-2
ALIGNMENT I.F.S. - STANDARD
PROCEDURES.........................2-2
ALIGNMENT LINK/COIL SUSPENSION -
STANDARD PROCEDURES...............2-5
ALIGNMENT, SPECIAL TOOLS -
HEADLAMP..........................8L-4
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD
PROCEDURE.....21-159,21-330,21-502,21-673
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-11
AMBIENT TEMP SENSOR -
INSTALLATION......................8M-13
AMBIENT TEMP SENSOR - OPERATION . . 8M-11
AMBIENT TEMP SENSOR - REMOVAL
....8M-12
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS & TESTING
...............8M-12
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-10
AN AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER
...........8O-4
ANTENNA - DIAGNOSIS AND TESTING
.....8A-5
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE - OPERATION
. . . 8A-4
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL
.................8A-10
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL
..................8A-9
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
.......................8E-12
ANTILOCK BRAKE - OPERATION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - REMOVAL,
CONTROLLER
.......................8E-12A-PILLAR GRAB HANDLE -
INSTALLATION......................23-119
A-PILLAR GRAB HANDLE - REMOVAL . . . 23-119
A-PILLAR TRIM - INSTALLATION.......23-119
A-PILLAR TRIM - REMOVAL...........23-119
A-PILLAR TWEETER SPEAKER -
INSTALLATION.......................8A-19
A-PILLAR TWEETER SPEAKER -
REMOVAL..........................8A-19
APPEARANCE TIPS - CLEANING.........30-21
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-8
APPLIQUE - INSTALLATION........23-62,23-67
APPLIQUE - REMOVAL...........23-62,23-67
AREA LEAKS - DIAGNOSIS AND
TESTING, REAR SEAL..................9-10
ARM / ADJUSTER ASSEMBLY -
INSTALLATION, ROCKER................9-85
ARM / ADJUSTER ASSEMBLY -
REMOVAL, ROCKER...................9-85
ARM / ADJUSTER ASSY - CLEANING,
ROCKER............................9-262
ARM / ADJUSTER ASSY - DESCRIPTION,
ROCKER............................9-261
ARM / ADJUSTER ASSY - INSPECTION,
ROCKER............................9-262
ARM / ADJUSTER ASSY -
INSTALLATION, ROCKER.....9-142,9-200,9-263
ARM / ADJUSTER ASSY - REMOVAL,
ROCKER.................9-142,9-200,9-261
ARM - DESCRIPTION, WIPER...........8R-11
ARM - INSTALLATION, LOWER
CONTROL.......................2-10,2-20
ARM - INSTALLATION, UPPER
CONTROL.......................2-13,2-24
ARM - INSTALLATION, WIPER..........8R-12
ARM - OPERATION, WIPER............8R-12
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-20
ARM - REMOVAL, UPPER CONTROL . . 2-13,2-23
ARM - REMOVAL, WIPER..............8R-12
ARMREST/CONSOLE - INSTALLATION,
CENTER SEAT......................23-132
ARMREST/CONSOLE - REMOVAL,
CENTER SEAT......................23-132
ARMREST/LATCH COVER -
INSTALLATION, CENTER SEAT.........23-132
ARMREST/LATCH COVER - REMOVAL,
CENTER SEAT......................23-132
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-3
ASD SENSE - PCM INPUT - OPERATION....8I-3
ASH RECEIVER - INSTALLATION........23-109
ASH RECEIVER - REMOVAL...........23-108
ASSEMBLE, OIL PUMP...........9-109,9-165
ASSEMBLY - INSTALLATION, ROCKER
ARM / ADJUSTER.....................9-85
ASSEMBLY - REMOVAL, ROCKER ARM /
ADJUSTER...........................9-85
ASSEMBLY, AUTOMATIC
TRANSMISSION - 42RE...............21-166
ASSEMBLY, AUTOMATIC
TRANSMISSION - 44RE...............21-337
ASSEMBLY, AUTOMATIC
TRANSMISSION - 46RE...............21-510
ASSEMBLY, AUTOMATIC
TRANSMISSION - 47RE...............21-681
ASSEMBLY, AXLE VACUUM MOTOR . . . 3-33,3-65
ASSEMBLY, DIFFERENTIAL . . . 3-128,3-159,3-188,
3-37,3-69,3-98
ASSEMBLY, DIFFERENTIAL - POWR-LOK . . 3-163
ASSEMBLY, DIFFERENTIAL - TRAC-LOK . . . 3-101,
3-132,3-190
ASSEMBLY, DISC BRAKE CALIPERS.......5-12
ASSEMBLY, DRIVER AIRBAG...........8O-17
ASSEMBLY, FLYWHEEL.................6-17
ASSEMBLY, FRONT CLUTCH.....21-206,21-376,
21-550,21-721
ASSEMBLY, FRONT SERVO......21-208,21-379,
21-553,21-723
ASSEMBLY, GLOVE BOX..............23-112
ASSEMBLY, HVAC HOUSING............24-36
ASSEMBLY, INSTRUMENT CLUSTER......8J-13
ASSEMBLY, MANUAL - NV3500
.........21-17
ASSEMBLY, MANUAL - NV4500
.........21-65
ASSEMBLY, MANUAL - NV5600
........21-110
ASSEMBLY, OIL PUMP
.................9-51
ASSEMBLY, OIL PUMP
. . . 21-212,21-382,21-558,
21-729ASSEMBLY, OVERDRIVE UNIT . . . 21-225,21-395,
21-569,21-742
ASSEMBLY, OVERHEAD CONSOLE -
OVERHEAD CONSOLE.................8M-7
ASSEMBLY, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON
RETAINER.......21-236,21-406,21-581,21-752
ASSEMBLY, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-412,21-588,21-760
ASSEMBLY, REAR CLUTCH......21-248,21-419,
21-593,21-766
ASSEMBLY, REAR SERVO.......21-251,21-422,
21-595,21-768
ASSEMBLY, TRANS COOLER -
3.9L/5.2L/5.9L........................7-82
ASSEMBLY, TRANSFER CASE - NV231HD . 21-834
ASSEMBLY, TRANSFER CASE - NV241HD . 21-904
ASSEMBLY, TRANSFER CASE - NV241LD . 21-869
ASSEMBLY, VALVE BODY . 21-294,21-466,21-638,
21-810
ASSEMBLY, WHEEL CYLINDERS..........5-31
ASSIST HANDLE - INSTALLATION.......23-124
ASSIST HANDLE - REMOVAL..........23-124
ASSY - CLEANING, ROCKER ARM /
ADJUSTER..........................9-262
ASSY - DESCRIPTION, ROCKER ARM /
ADJUSTER..........................9-261
ASSY - INSPECTION, ROCKER ARM /
ADJUSTER..........................9-262
ASSY - INSTALLATION, ROCKER ARM /
ADJUSTER................9-142,9-200,9-263
ASSY - REMOVAL, ROCKER ARM /
ADJUSTER................9-142,9-200,9-261
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-2
AUDIO SYSTEMS, SPECIAL TOOLS.......8A-4
AUGAT - INSTALLATION, CONNECTOR . . 8W-01-8
AUGAT - REMOVAL, CONNECTOR.....8W-01-8
AUTO. TRANS. - INSTALLATION, DIESEL
WITH..........................8P-11,8P-4
AUTO. TRANS. - REMOVAL, DIESEL
WITH...........................8P-4,8P-8
AUTOMATIC DAY / NIGHT MIRROR -
DESCRIPTION.......................8N-10
AUTOMATIC DAY / NIGHT MIRROR -
INSTALLATION......................8N-12
AUTOMATIC DAY / NIGHT MIRROR -
OPERATION.........................8N-11
AUTOMATIC DAY / NIGHT MIRROR -
REMOVAL..........................8N-12
AUTOMATIC DAY/NIGHT MIRROR -
DIAGNOSIS AND TESTING.............8N-11
AUTOMATIC SHUT DOWN RELAY -
INSTALLATION........................8I-5
AUTOMATIC SHUT DOWN RELAY -
REMOVAL............................8I-4
AUTOMATIC TRANSMISSION - 42RE -
ASSEMBLY.........................21-166
AUTOMATIC TRANSMISSION - 42RE -
CLEANING.........................21-165
AUTOMATIC TRANSMISSION - 42RE -
DESCRIPTION
......................21-135
AUTOMATIC TRANSMISSION - 42RE -
DISASSEMBLY
......................21-160
AUTOMATIC TRANSMISSION - 42RE -
INSPECTION
.......................21-165
AUTOMATIC TRANSMISSION - 42RE -
INSTALLATION
......................21-173
AUTOMATIC TRANSMISSION - 42RE -
OPERATION
........................21-137
AUTOMATIC TRANSMISSION - 42RE -
REMOVAL
.........................21-159
AUTOMATIC TRANSMISSION - 44RE -
ASSEMBLY
.........................21-337
AUTOMATIC TRANSMISSION - 44RE -
CLEANING
.........................21-336
AUTOMATIC TRANSMISSION - 44RE -
DESCRIPTION
......................21-306
AUTOMATIC TRANSMISSION - 44RE -
DISASSEMBLY
......................21-331
AUTOMATIC TRANSMISSION - 44RE -
INSPECTION
.......................21-337
AUTOMATIC TRANSMISSION - 44RE -
INSTALLATION
......................21-344
AUTOMATIC TRANSMISSION - 44RE -
OPERATION
........................21-308
2 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

CENTER HIGH MOUNTED STOP LAMP -
INSTALLATION........................8L-6
CENTER HIGH MOUNTED STOP LAMP -
REMOVAL...........................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION..................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL.....................8L-6
CENTER SEAT ARMREST/CONSOLE -
INSTALLATION......................23-132
CENTER SEAT ARMREST/CONSOLE -
REMOVAL.........................23-132
CENTER SEAT ARMREST/LATCH COVER -
INSTALLATION......................23-132
CENTER SEAT ARMREST/LATCH COVER -
REMOVAL.........................23-132
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-11
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING........................8E-4
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY..................Intro.-12
CHAIN COVER(S) - INSTALLATION,
TIMING BELT..........9-113,9-169,9-226,9-56
CHAIN COVER(S) - REMOVAL, TIMING
BELT ................9-113,9-169,9-225,9-56
CHAIN STRETCH - INSPECTION,
MEASURING TIMING....9-114,9-170,9-227,9-58
CHANNEL - INSTALLATION, GLASS RUN . . 23-70
CHANNEL - REMOVAL, GLASS RUN......23-70
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-46
CHARGE AIR COOLER AND PLUMBING -
CLEANING..........................11-18
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION.......................11-17
CHARGE AIR COOLER AND PLUMBING -
INSPECTION........................11-18
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION.......................11-18
CHARGE AIR COOLER AND PLUMBING -
OPERATION.........................11-17
CHARGE AIR COOLER AND PLUMBING -
REMOVAL..........................11-17
CHARGING - DESCRIPTION.............8F-27
CHARGING - OPERATION..............8F-27
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-9
CHARGING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-27
CHART, SPECIFICATIONS - TORQUE........5-3
CHART, SPECIFICATIONS -
TORQUE.............19-19,19-39,19-41,19-9
CHART, SPECIFICATIONS -
TORQUE.....................2-15,2-27,2-8
CHART, SPECIFICATIONS - TORQUE......22-11
CHARTS - DIAGNOSIS AND TESTING,
DIAGNOSIS......21-149,21-320,21-492,21-663
CHARTS - DIAGNOSIS AND TESTING,
SMOKE DIAGNOSIS...................9-234
CHASSIS ADAPTER BRACKET -
INSTALLATION, CAB...................13-9
CHASSIS ADAPTER BRACKET -
REMOVAL, CAB.......................13-9
CHECK - INSTALLATION...............23-78
CHECK - REMOVAL...................23-78
CHECK - STANDARD PROCEDURE,
COOLANT LEVEL......................7-16
CHECK - STANDARD PROCEDURE, FLUID
LEVEL..........21-199,21-370,21-545,21-715
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME . . . 21-209,21-379,21-554,21-724
CHECK CABLE - INSTALLATION.........23-63
CHECK CABLE - REMOVAL.............23-62
CHECK GAUGES INDICATOR -
DESCRIPTION.......................8J-17
CHECK GAUGES INDICATOR -
OPERATION.........................8J-17
CHECK OUT - STANDARD PROCEDURE,
OWNER............................30-22
CHECK VALVE - DESCRIPTION, ONE WAY . 25-30
CHECK VALVE - DESCRIPTION, VACUUM
. . 24-28
CHECK VALVE - DIAGNOSIS AND
TESTING, ONE-WAY
..................25-30
CHECK VALVE - INSTALLATION, ONE
WAY
...............................25-30
CHECK VALVE - INSTALLATION, VACUUM
. 24-29
CHECK VALVE - OPERATION, ONE WAY
. . . 25-30CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, ONE WAY....25-30
CHECK VALVE - REMOVAL, VACUUM.....24-29
CHECKING BATTERY ELECTROLYTE
LEVEL - STANDARD PROCEDURE.........8F-8
CHECKING TRANSMISSION CLUTCH AND
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR................21-147,21-318
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-4
CHILD TETHER - INSTALLATION..........8O-9
CHILD TETHER - REMOVAL.............8O-9
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-2
CHIME WARNING SYSTEM - OPERATION . . . 8B-1
CHOKE RELAY - DESCRIPTION, RADIO....8A-8
CHOKE RELAY - DIAGNOSIS AND
TESTING, RADIO......................8A-8
CHOKE RELAY - INSTALLATION, RADIO....8A-9
CHOKE RELAY - OPERATION, RADIO......8A-8
CHOKE RELAY - REMOVAL, RADIO.......8A-9
CIGAR LIGHTER - DIAGNOSIS &
TESTING.........................8W-97-2
CIGAR LIGHTER OUTLET - DESCRIPTION . 8W-97-2
CIGAR LIGHTER OUTLET -
INSTALLATION....................8W-97-3
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL....8W-97-3
CIRCUIT ACTUATION TEST MODE -
DESCRIPTION........................25-1
CIRCUIT BREAKER - DESCRIPTION....8W-97-4
CIRCUIT BREAKER - DIAGNOSIS &
TESTING.........................8W-97-4
CIRCUIT SENSE - DESCRIPTION,
IGNITION...........................8E-17
CIRCUIT SENSE - OPERATION, IGNITION . . 8E-19
CIRCUITS - DIESEL - OPERATION,
NON-MONITORED....................25-23
CIRCUITS - GAS ENGINES - OPERATION,
NON-MONITORED....................25-22
CLAMPS - DESCRIPTION, HOSE...........7-2
CLAMPS - OPERATION, HOSE.............7-2
CLASSIFICATION OF LUBRICANTS -
STANDARD PROCEDURE.................0-3
CLEANER ELEMENT - INSTALLATION,
AIR ...............................9-245
CLEANER ELEMENT - REMOVAL, AIR.....9-244
CLEANING AND INSPECTION, OIL
COOLER & LINES....................9-296
CLEANING, APPEARANCE TIPS..........30-21
CLEANING/REVERSE FLUSHING -
STANDARD PROCEDURE, COOLING
SYSTEM............................7-16
CLEARANCE - STANDARD PROCEDURE,
CONNECTING ROD BEARING AND
CRANKSHAFT JOURNAL...............9-274
CLEARANCE - STANDARD PROCEDURE,
MAIN BEARING......................9-275
CLEARANCE LAMP - INSTALLATION.......8L-6
CLEARANCE LAMP - REMOVAL..........8L-6
CLOCKSPRING - DESCRIPTION.........8O-10
CLOCKSPRING - INSTALLATION.........8O-13
CLOCKSPRING - OPERATION...........8O-10
CLOCKSPRING - REMOVAL............8O-11
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-11
CLOSURE PANEL TRIM - INSTALLATION,
REAR.............................23-121
CLOSURE PANEL TRIM - REMOVAL,
REAR.............................23-120
CLUB/QUAD CAB - INSTALLATION.......8O-20
CLUB/QUAD CAB - REMOVAL...........8O-19
CLUSTER - ASSEMBLY, INSTRUMENT....8J-13
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-6
CLUSTER - DISASSEMBLY, INSTRUMENT . . 8J-11
CLUSTER - INSTALLATION, INSTRUMENT . 8J-14
CLUSTER - OPERATION, INSTRUMENT.....8J-3
CLUSTER - REMOVAL, INSTRUMENT
.....8J-10
CLUSTER BEZEL - INSTALLATION
.......23-110
CLUSTER BEZEL - REMOVAL
..........23-109
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
DESCRIPTION, FAN DRIVE VISCOUS
......7-56
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
OPERATION, FAN DRIVE VISCOUS
........7-56CLUTCH - 5.9L DIESEL - DESCRIPTION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - 5.9L DIESEL - OPERATION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - ASSEMBLY, FRONT . . . 21-206,21-376,
21-550,21-721
CLUTCH - ASSEMBLY, REAR....21-248,21-419,
21-593,21-766
CLUTCH - CLEANING, REAR....21-247,21-418,
21-593,21-765
CLUTCH - DESCRIPTION.................6-1
CLUTCH - DESCRIPTION, A/C
COMPRESSOR.......................24-13
CLUTCH - DESCRIPTION, FRONT . 21-202,21-373,
21-548,21-718
CLUTCH - DESCRIPTION, OVERDRIVE . . . 21-214,
21-385,21-560,21-731
CLUTCH - DESCRIPTION, REAR . . 21-246,21-417,
21-591,21-764
CLUTCH - DIAGNOSTIC AND TESTING......6-2
CLUTCH - DISASSEMBLY, FRONT......21-202,
21-373,21-549,21-719
CLUTCH - DISASSEMBLY, REAR . 21-247,21-418,
21-592,21-765
CLUTCH - INSPECTION, A/C
COMPRESSOR.......................24-16
CLUTCH - INSPECTION, FRONT . . 21-205,21-376,
21-550,21-721
CLUTCH - INSPECTION, REAR . . . 21-248,21-419,
21-593,21-765
CLUTCH - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH - OPERATION....................6-1
CLUTCH - OPERATION, A/C
COMPRESSOR.......................24-13
CLUTCH - OPERATION, FRONT . . 21-202,21-373,
21-548,21-718
CLUTCH - OPERATION, OVERDRIVE....21-214,
21-385,21-560,21-731
CLUTCH - OPERATION, REAR . . . 21-246,21-417,
21-592,21-764
CLUTCH - REMOVAL, A/C COMPRESSOR . . 24-14
CLUTCH - SPECIFICATIONS...............6-7
CLUTCH - WARNING....................6-2
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING TRANSMISSION......21-147,21-318
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
TESTING TRANSMISSION.......21-490,21-661
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-13
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - ASSEMBLY,
OVERRUNNING . . . 21-236,21-406,21-581,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - CLEANING, OVERRUNNING . 21-236,
21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DESCRIPTION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DISASSEMBLY,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - INSPECTION,
OVERRUNNING . . . 21-236,21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - OPERATION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-13
CLUTCH DISC - DESCRIPTION............6-7
CLUTCH DISC - INSTALLATION............6-9
CLUTCH DISC - OPERATION..............6-8
CLUTCH DISC - REMOVAL...............6-8
CLUTCH HOUSING - DIAGNOSIS AND
TESTING............................6-11
CLUTCH HOUSING - INSTALLATION.......6-13
CLUTCH HOUSING - REMOVAL...........6-13
CLUTCH PEDAL - INSTALLATION
.........6-19
CLUTCH PEDAL - REMOVAL
.............6-18
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION
........................6-22
CLUTCH PEDAL POSITION SWITCH -
OPERATION
..........................6-22
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR
.......................24-17
BR/BEINDEX 7
Description Group-Page Description Group-Page Description Group-Page

CONTROL/CENTRAL TIMER MODULE -
INSTALLATION, BODY..................8E-6
CONTROL/CENTRAL TIMER MODULE -
OPERATION, BODY....................8E-3
CONTROL/CENTRAL TIMER MODULE -
REMOVAL, BODY......................8E-5
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION.......................8E-11
CONTROLLER ANTILOCK BRAKE -
INSTALLATION.......................8E-12
CONTROLLER ANTILOCK BRAKE -
OPERATION.........................8E-11
CONTROLLER ANTILOCK BRAKE -
REMOVAL..........................8E-12
CONTROLS - DIAGNOSIS AND TESTING,
OVERDRIVE
ELECTRICAL.....21-215,21-386,21-579,21-732
CONVERTER - 3.9L/5.2L/5.9L -
DESCRIPTION, CATALYTIC...............11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSPECTION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSTALLATION, CATALYTIC..............11-5
CONVERTER - 3.9L/5.2L/5.9L -
OPERATION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
REMOVAL, CATALYTIC..................11-5
CONVERTER - 5.9L HEAVY DUTY/8.0L -
DESCRIPTION, CATALYTIC...............11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSPECTION, CATALYTIC................11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSTALLATION, CATALYTIC..............11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
OPERATION, CATALYTIC................11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
REMOVAL, CATALYTIC..................11-6
CONVERTER - DESCRIPTION,
TORQUE........21-256,21-427,21-600,21-773
CONVERTER - INSTALLATION,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER - OPERATION,
TORQUE........21-260,21-430,21-604,21-777
CONVERTER - REMOVAL,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
DESCRIPTION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
OPERATION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
STANDARD PROCEDURE,
TORQUE........21-262,21-432,21-606,21-778
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND
TESTING........21-148,21-319,21-491,21-662
COOLANT - DESCRIPTION...............7-40
COOLANT - OPERATION
................7-40
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
..................7-16
COOLANT FLOW - DIAGNOSIS AND
TESTING, RADIATOR
...........7-59,7-61,7-63
COOLANT LEVEL CHECK - STANDARD
PROCEDURE
.........................7-16
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
DESCRIPTION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
INSTALLATION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
OPERATION
..........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
REMOVAL
...........................7-41
COOLANT RECOVERY CONTAINER - 8.0L
- DESCRIPTION
.......................7-42
COOLANT RECOVERY CONTAINER - 8.0L
- OPERATION
.........................7-42
COOLANT SELECTION-ADDITIVES -
STANDARD PROCEDURE
................7-17
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE
............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE
...........7-48COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-48
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE...........7-50
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-49
COOLANT THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE................7-55
COOLANT THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE...................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE....................7-55
COOLANT THERMOSTAT - 8.0L -
DESCRIPTION, ENGINE.................7-52
COOLANT THERMOSTAT - 8.0L -
INSTALLATION, ENGINE................7-53
COOLANT THERMOSTAT - 8.0L -
OPERATION, ENGINE...................7-52
COOLANT THERMOSTAT - 8.0L -
REMOVAL, ENGINE....................7-52
COOLER - 3.9L/5.2L/5.9L - ASSEMBLY,
TRANS..............................7-82
COOLER - 3.9L/5.2L/5.9L -
DESCRIPTION, TRANS.................7-79
COOLER - 3.9L/5.2L/5.9L -
DISASSEMBLY, TRANS...................7-81
COOLER - 3.9L/5.2L/5.9L -
INSTALLATION, TRANS.................7-82
COOLER - 3.9L/5.2L/5.9L - OPERATION,
TRANS..............................7-79
COOLER - 3.9L/5.2L/5.9L - REMOVAL,
TRANS..............................7-81
COOLER - 5.9L DIESEL - DESCRIPTION,
TRANS..............................7-85
COOLER - 5.9L DIESEL - INSTALLATION,
TRANS..............................7-88
COOLER - 5.9L DIESEL - OPERATION,
TRANS..............................7-85
COOLER - 8.0L - DESCRIPTION, TRANS....7-82
COOLER - 8.0L - INSTALLATION, TRANS . . . 7-85
COOLER - 8.0L - OPERATION, TRANS.....7-82
COOLER - 8.0L - REMOVAL, TRANS.......7-84
COOLER - INSTALLATION, AIR TO OIL.....7-88
COOLER & LINES - CLEANING AND
INSPECTION, OIL.....................9-296
COOLER - REMOVAL, AIR TO OIL.........7-87
COOLER - REMOVAL, WATER TO OIL......7-87
COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL...........7-80,7-83,7-86
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION OIL...........7-79,7-83,7-85
COOLER AND PLUMBING - CLEANING,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR............11-17
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR...........11-18
COOLER AND PLUMBING - OPERATION,
CHARGE AIR........................11-17
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR........................11-17
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-80,7-83,7-86
COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-79,7-83,7-85
COOLING, SPECIAL TOOLS
..............7-18
COOLING SYSTEM - OPERATION
..........7-4
COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
DRAINING
...........................7-15COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
REFILLING...........................7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, DRAINING.....7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, REFILLING.....7-15
COOLING SYSTEM CLEANING/REVERSE
FLUSHING - STANDARD PROCEDURE.....7-16
COOLING SYSTEM DIESEL ENGINE -
DIAGNOSIS AND TESTING..............7-12
COOLING SYSTEM FLOW - 3.9L/5.2L/
5.9L ENGINE - DESCRIPTION.............7-1
COOLING SYSTEM FLOW - 5.9L DIESEL
- DESCRIPTION........................7-1
COOLING SYSTEM GAS ENGINE -
DIAGNOSIS AND TESTING...............7-7
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-5
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-55
CORE - INSTALLATION, HEATER.........24-56
CORE - OPERATION, HEATER...........24-55
CORE - REMOVAL, HEATER............24-56
CORE GROUND STRAP - INSTALLATION,
HEATER............................8A-15
CORE GROUND STRAP - REMOVAL,
HEATER............................8A-14
CORNER SEAL - INSTALLATION, FRONT
DOOR UPPER......................23-154
CORNER SEAL - REMOVAL, FRONT
DOOR UPPER........................23-154
COUPLERS - DESCRIPTION, A/C LINE....24-40
COUPLERS - OPERATION, A/C LINE......24-41
COUPLERS - STANDARD PROCEDURE,
A/C LINE...........................24-43
COVER - INSTALLATION, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - INSTALLATION, COWL TRIM . . . 23-120
COVER - INSTALLATION, GEAR HOUSING . 9-307
COVER - INSTALLATION, INSTRUMENT
PANEL TOP........................23-115
COVER - INSTALLATION, SEAT BACK....23-137
COVER - INSTALLATION, SEAT CUSHION . 23-139
COVER - INSTALLATION, SHIFT . . . 21-133,21-90
COVER - INSTALLATION, STANCHION....23-143
COVER - INSTALLATION, STEERING
COLUMN OPENING..................23-116
COVER - REMOVAL, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - REMOVAL, COWL TRIM.......23-119
COVER - REMOVAL, GEAR HOUSING.....9-306
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-114
COVER - REMOVAL, SEAT BACK........23-137
COVER - REMOVAL, SEAT CUSHION.....23-139
COVER - REMOVAL, SHIFT.......21-132,21-90
COVER - REMOVAL, STANCHION.......23-143
COVER - REMOVAL, STEERING COLUMN
OPENING..........................23-115
COVER - REMOVAL, WHEEL............22-12
COVER - SPLIT BENCH - INSTALLATION,
SEAT BACK........................23-138
COVER - SPLIT BENCH - INSTALLATION,
SEAT CUSHION.....................23-140
COVER - SPLIT BENCH - REMOVAL,
SEAT BACK........................23-137
COVER - SPLIT BENCH - REMOVAL,
SEAT CUSHION.....................23-139
COVER GASKET - DESCRIPTION,
CYLINDER...........................9-79
COVER GASKET - DESCRIPTION,
CYLINDER HEAD......................9-22
COVER GASKET - OPERATION,
CYLINDER HEAD......................9-22
COVER INSTALLED - INSTALLATION,
FRONT OIL SEAL - FRONT.............9-205
COVER INSTALLED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER REMOVED - INSTALLATION,
FRONT OIL SEAL - FRONT
.............9-205
COVER REMOVED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER(S) - CLEANING, CYLINDER HEAD
. 9-138,
9-194,9-24,9-253,9-81
COVER(S) - DESCRIPTION, CYLINDER
HEAD
..............................9-194
BR/BEINDEX 9
Description Group-Page Description Group-Page Description Group-Page

FAN - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION, RADIATOR..............7-43
FAN - 3.9L/5.2L/5.9L/8.0L - REMOVAL,
RADIATOR...........................7-42
FAN - 5.9L DIESEL - CLEANING,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR...........................7-45
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR...........................7-44
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS........................7-56,7-58
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - DESCRIPTION.......7-56
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - OPERATION.........7-56
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-57
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-57
FASCIA - ADJUSTMENT, FRONT..........13-2
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, FRONT LOWER . . . 13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, FRONT LOWER......13-3
FASCIA-SPORT - INSTALLATION, FRONT . . . 13-3
FASCIA-SPORT - REMOVAL, FRONT.......13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-3
FASTENER USAGE - DESCRIPTION......Intro.-6
FASTENERS - DESCRIPTION, PUSH-IN.....23-1
FEATURES - DESCRIPTION,
PROGRAMMABLE ELECTRONIC.........30-20
FEATURES - OPERATION,
PROGRAMMABLE ELECTRONIC.........30-20
FENDER - INSTALLATION, LEFT FRONT . . . 23-93
FENDER - INSTALLATION, REAR.........23-95
FENDER - INSTALLATION, RIGHT FRONT . . 23-94
FENDER - REMOVAL, LEFT FRONT.......23-92
FENDER - REMOVAL, REAR............23-95
FENDER - REMOVAL, RIGHT FRONT......23-94
FILL - STANDARD PROCEDURE,
TRANSMISSION . . . 21-201,21-372,21-547,21-718
FILL DOOR - INSTALLATION, FUEL.......23-95
FILL DOOR - REMOVAL, FUEL..........23-95
FILLER CAP - DESCRIPTION, FUEL.......25-33
FILLER CAP - OPERATION, FUEL........25-33
FILLER CAP - REMOVAL/INSTALLATION,
FUEL..............................25-33
FILTER - DESCRIPTION, PCV...........25-35
FILTER - INSTALLATION, AIR PUMP......25-29
FILTER - INSTALLATION, INLET..........14-22
FILTER - INSTALLATION, OIL . 9-105,9-161,9-218,
9-296,9-48
FILTER - REMOVAL, AIR PUMP.........25-29
FILTER - REMOVAL, INLET.............14-22
FILTER - REMOVAL, OIL.....9-105,9-161,9-218,
9-296,9-48
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-56
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-59
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-61
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-59
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-60
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID.....21-201,21-372,21-547,
21-717
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL...................14-5
FILTER/PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-6
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL.....................14-5
FILTER/PRESSURE REGULATOR -
REMOVAL, FUEL
......................14-5
FINAL STEPS - NEW VEHICLE
PREPARATION FORM
.................30-22
FINISH - DESCRIPTION, BASE
COAT/CLEAR COAT
..................23-129
FINISH - INSPECTION, FIT
........30-10,30-12
FINISH - OPERATION, BASE COAT/CLEAR
COAT
.............................23-129FIRING ORDER, 3.9L V-6 ENGINE -
ENGINE..............................8I-2
FIRING ORDER, 5.2L/5.9L V-8 ENGINES -
ENGINE..............................8I-2
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-58
FIT AND FINISH - INSPECTION.....30-10,30-12
FITTING - DESCRIPTION, QUICK
CONNECT...........................14-22
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING . . 9-144,9-202,9-88
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING......9-146,9-90
FITTING - STANDARD PROCEDURE,
MAIN BEARING..................9-203,9-33
FITTING - STANDARD PROCEDURE,
PISTON...............9-153,9-208,9-40,9-97
FITTING - STANDARD PROCEDURE,
PISTON RING...............9-154,9-41,9-98
FITTING, CONNECTING ROD BEARINGS -
STANDARD PROCEDURE-CONNECTING
ROD BEARING........................9-31
FITTING PISTON RINGS - STANDARD
PROCEDURE........................9-211
FITTING, PISTON RINGS - STANDARD
PROCEDURE-PISTON RING.............9-288
FITTINGS - STANDARD PROCEDURES,
QUICK-CONNECT.....................14-22
FIXED ORIFICE TUBE - DIAGNOSIS AND
TESTING...........................24-54
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-74
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-74
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLASHER - DESCRIPTION, COMBINATION . . 8L-7
FLASHER - INSTALLATION,
COMBINATION........................8L-8
FLASHER - OPERATION, COMBINATION....8L-7
FLASHER - REMOVAL, COMBINATION.....8L-8
FLOOR MATS - INSTALLATION, CARPETS . 23-123
FLOOR MATS - REMOVAL, CARPETS....23-123
FLOOR SHIFT BOOT - INSTALLATION,
4WD .............................23-122
FLOOR SHIFT BOOT - REMOVAL, 4WD . . . 23-122
FLOOR STOWAGE TRAY -
INSTALLATION, REAR................23-121
FLOOR STOWAGE TRAY - REMOVAL,
REAR.............................23-121
FLOW - 3.9L/5.2L/5.9L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-59,7-61,7-63
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID - DESCRIPTION, TRANSFER CASE....0-5
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT.....21-199,21-370,21-545,
21-715
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE . 21-201,21-372,21-547,
21-717
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE...........21-851,21-885,21-922
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER
...................8J-36
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
. . . 21-148,21-319,21-491,
21-662
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-199,
21-370,21-545,21-715FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL CHECK - STANDARD
PROCEDURE.....21-199,21-370,21-545,21-715
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID LEVELS - INSPECTION............30-4
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUID TYPES - DESCRIPTION.............0-5
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-16
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-80,7-83,7-86
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-79,7-83,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-32
FLYWHEEL - ASSEMBLY................6-17
FLYWHEEL - DESCRIPTION..............6-16
FLYWHEEL - DIAGNOSIS AND TESTING....6-17
FLYWHEEL - DISASSEMBLY.............6-17
FLYWHEEL - OPERATION...............6-16
FOG LAMP - DIAGNOSIS AND TESTING....8L-9
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-12
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-11
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-68
FORM, FINAL STEPS - NEW VEHICLE
PREPARATION.......................30-22
FORM-IN-PLACE GASKETS & SEALERS -
STANDARD PROCEDURE.....9-11,9-125,9-180,
9-237,9-68
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - DESCRIPTION.................13-6
FRAME - FRAME SERVICE..............13-6
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-7
FRAME SERVICE, FRAME...............13-6
FRONT - 2WD - DESCRIPTION.........2-7,2-8
FRONT - 4WD - DESCRIPTION...........2-14
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...................9-147,9-34,9-91
FRONT - INSTALLATION............5-14,5-27
FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, 1500/2500.......5-22
FRONT - INSTALLATION, 3500...........5-22
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL..............9-148,9-277,9-34,9-91
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-8
FRONT - OPERATION, CRANKSHAFT OIL
SEAL......................9-147,9-34,9-91
FRONT - REMOVAL................5-10,5-24
FRONT - REMOVAL, 1500/2500..........5-21
FRONT - REMOVAL, 3500...............5-22
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL.................9-147,9-276,9-34,9-91
FRONT - REMOVAL, PROPELLER SHAFT....3-8
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-1
FRONT AXLE - 216FBI - ADJUSTMENTS....3-17
FRONT AXLE - 216FBI - DESCRIPTION.....3-12
FRONT AXLE - 216FBI - INSTALLATION....3-17
FRONT AXLE - 216FBI - OPERATION......3-12
FRONT AXLE - 216FBI - REMOVAL
........3-16
FRONT AXLE - 248FBI - ADJUSTMENTS
....3-50
FRONT AXLE - 248FBI - DESCRIPTION
.....3-45
FRONT AXLE - 248FBI - INSTALLATION
....3-50
FRONT AXLE - 248FBI - OPERATION
......3-45
14 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - OPERATION.............8H-3
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HOSE - OPERATION, CRANKCASE VENT . . . 25-32
HOSE CLAMPS - DESCRIPTION...........7-2
HOSE CLAMPS - OPERATION.............7-2
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-74
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-78
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-77
HOSES - PRESSURE - DESCRIPTION.....19-37
HOSES - PRESSURE - OPERATION.......19-37
HOSES - RETURN - DESCRIPTION.......19-37
HOSES - RETURN - OPERATION.........19-37
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT..............24-42
HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH.............................6-11
HOUSING - DISASSEMBLY, HVAC........24-36
HOUSING - INSTALLATION, CLUTCH......6-13
HOUSING - INSTALLATION, GEAR........9-305
HOUSING - INSTALLATION, HVAC........24-37
HOUSING - INSTALLATION, LOCK
CYLINDER..........................19-11
HOUSING - REMOVAL, CLUTCH..........6-13
HOUSING - REMOVAL, GEAR...........9-304
HOUSING - REMOVAL, HVAC...........24-35
HOUSING - REMOVAL, LOCK CYLINDER . . 19-10
HOUSING BUSHING - INSTALLATION,
EXTENSION......21-198,21-369,21-544,21-714
HOUSING BUSHING - REMOVAL,
EXTENSION......21-198,21-369,21-544,21-714
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-850,21-885,
21-921
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION . . . 21-850,21-885,21-921
HOUSING COVER - INSTALLATION, GEAR . 9-307
HOUSING COVER - REMOVAL, GEAR.....9-306
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER . . . 21-148,21-319,21-491,
21-662
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-37
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-36
HOUSING PLUG - INSTALLATION,
STEERING GEAR.....................19-27
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-27
HOUSING SEAL - INSTALLATION,
ADAPTER.....................21-132,21-87
HOUSING SEAL - INSTALLATION,
EXTENSION......21-132,21-198,21-369,21-544,
21-715,21-87
HOUSING SEAL - REMOVAL, ADAPTER . . 21-132,
21-87
HOUSING SEAL - REMOVAL,
EXTENSION......21-132,21-198,21-369,21-544,
21-714,21-87
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H.P. - DESCRIPTION, FUEL PUMP 235....14-66
H.P. - DESCRIPTION, FUEL PUMP 245....14-65
HUB / BEARING - INSTALLATION..........2-9
HUB / BEARING - REMOVAL..............2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-36
HVAC HOUSING - INSTALLATION........24-37
HVAC HOUSING - REMOVAL
............24-35
HVAC HOUSING INLET BAFFLE -
INSTALLATION
.......................24-37
HVAC HOUSING INLET BAFFLE -
REMOVAL
..........................24-36
HVAC SYSTEM AIRFLOW - DESCRIPTION
. 24-31
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING
........................5-17HYDRAULIC LIFTERS - CLEANING . . 9-152,9-208
HYDRAULIC LIFTERS - INSTALLATION . . . 9-152,
9-208
HYDRAULIC LIFTERS - REMOVAL . . . 9-152,9-207
HYDRAULIC LIFTERS (CAM IN BLOCK) -
CLEANING.......................9-39,9-96
HYDRAULIC LIFTERS (CAM IN BLOCK) -
INSTALLATION....................9-39,9-96
HYDRAULIC LIFTERS (CAM IN BLOCK) -
REMOVAL.......................9-39,9-96
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-144,21-315,
21-487,21-658
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS . . 21-174,21-345,21-520,21-690
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING..............9-151,9-206,9-38,9-95
HYDRAULIC/MECHANICAL -
DESCRIPTION.........................5-4
HYDRAULIC/MECHANICAL - WARNING.....5-5
HYDROMETER TEST - STANDARD
PROCEDURE........................8F-12
HYDROSTATIC LOCK - STANDARD
PROCEDURE......9-11,9-125,9-181,9-238,9-68
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-3
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD.........................8L-29
IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE.............Intro.-10
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT......................Intro.-12
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-41
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-41
I.F.S. - STANDARD PROCEDURES,
ALIGNMENT...........................2-2
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 3.9L/5.2L/
5.9L ENGINES........................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-3
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-10
IGNITION TIMING, SPECIFICATIONS.......8I-3
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-15
IMPORTANCE OF CAREFUL NEW
VEHICLE PREPARATION -
DESCRIPTION, THE....................30-1
INCH - INSTALLATION, 12 1/8...........5-28
INCH - INSTALLATION, REAR BRAKE
SHOES-11...........................5-27
INCH - REMOVAL, 12 1/8...............5-26
INCH - REMOVAL, REAR BRAKE
SHOES-11...........................5-25
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF.....21-199,21-370,
21-545,21-715
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-16
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE
.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR
..........................8J-21
INDICATOR - DESCRIPTION, HIGH BEAM
. . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL
. . . 8J-23
INDICATOR - DESCRIPTION, OVERDRIVE
OFF
...............................8J-27INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-28
INDICATOR - DESCRIPTION,
TRANSMISSION OVERTEMP............8J-31
INDICATOR - DESCRIPTION, UPSHIFT....8J-33
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-22
INDICATOR - DIAGNOSIS AND TESTING,
VTSS...............................8Q-3
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID......................8J-36
INDICATOR - OPERATION, ABS..........8J-14
INDICATOR - OPERATION, AIRBAG.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-16
INDICATOR - OPERATION, CHECK
GAUGES............................8J-17
INDICATOR - OPERATION, CRUISE.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR...........................8J-21
INDICATOR - OPERATION, HIGH BEAM....8J-22
INDICATOR - OPERATION, LOW FUEL.....8J-23
INDICATOR - OPERATION, OVERDRIVE
OFF ...............................8J-27
INDICATOR - OPERATION, SEATBELT.....8J-27
INDICATOR - OPERATION, SERVICE
REMINDER..........................8J-28
INDICATOR - OPERATION,
TRANSMISSION OVERTEMP............8J-31
INDICATOR - OPERATION, UPSHIFT......8J-33
INDICATOR - OPERATION, VTSS.........8Q-3
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-35
INDICATOR - OPERATION, WASHER
FLUID..............................8J-35
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-37
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-24
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-24
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-11
INDICATOR (TRANSFER CASE) -
DESCRIPTION, SHIFT.................8J-29
INDICATOR (TRANSFER CASE) -
OPERATION, SHIFT...................8J-29
INDICATORS - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-7
INDICATORS - DIAGNOSIS AND
TESTING, TURN SIGNAL...............8J-32
INDICATORS - OPERATION, TURN
SIGNAL............................8J-32
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP
.............................19-31
INJECTION - SPECIFICATIONS, TORQUE -
GAS FUEL
..........................14-35
INJECTION PUMP - DESCRIPTION, AIR
. . . 25-28
INJECTION PUMP - DIAGNOSIS AND
TESTING, AIR
.......................25-28
INJECTION PUMP - INSTALLATION, AIR
. . . 25-29
INJECTION PUMP - INSTALLATION, FUEL
. 14-71
INJECTION PUMP - OPERATION, AIR
.....25-28
INJECTION PUMP - OPERATION, FUEL
....14-66
INJECTION PUMP - REMOVAL, AIR
......25-29
INJECTION PUMP - REMOVAL, FUEL
.....14-68
INJECTION PUMP DATA PLATE,
SPECIFICATIONS - FUEL
...............14-73
INJECTION PUMP RELAY -
DESCRIPTION, FUEL
..................14-99
INJECTION PUMP RELAY - OPERATION,
FUEL
..............................14-99
18 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page