2001 DODGE RAM lock

STANDARD PROCEDURE - PRE DELIVERY
STORAGE
(1) If possible, store vehicles indoors, in clean, dry
places. If vehicles must be stored outdoors:
²Try to avoid storage locations that are near any
obvious sources of industrial or environmental con-
tamination (e.g., trees, factories, steam or vapor
vents, railroad tracks, etc.)
²Maintain tight security to help prevent pilferage
and vandalism, and inspect each vehicle regularly to
check for such damage
²If the vehicle must be parked on an incline, park
it with the front end higher than the rear; this will
prevent ªhydrostatic lockº caused by fuel draining
into the engine
²Rinse the vehicle at least once a week. Snow
should be washed away more often, since it can trap
harmful contaminants. Dry all horizontal surfaces
(2) The IOD fuse should be removed in order to
prevent battery drain and possible damage.
(3) Check the vehicle's coolant and anti-freeze pro-
tection.
(4) Check the vehicle's battery at least once a
month for a proper charge (at least 12.4 volts).
Charge the battery if necessary. This will help pre-
vent freezing and deterioration.
(5) Check the vehicle's tires and inflate them to
their maximum recommended levels. Move the vehi-
cles periodically to avoid ªflatspottingº the tires.
(6) Do not engage the parking brake; keep it in the
OFF position.
(7) Keep all windows closed, all doors locked, and
all trim covers intact and in place.
(8) Do not use chalks, crayons or any marker con-
taining abrasives on painted, plated or glass sur-
faces.
(9) Always use seat covers when moving a vehicle.
PROGRAMMABLE
ELECTRONIC FEATURES
DESCRIPTION
The programming of electronic features applies to
specific DaimlerChrysler Corporation vehicles. Not
all vehicles are equipped with these electronic fea-
tures, and not all vehicles equipped with electronic
features have all the available features. Programma-
ble electronic features are subject to change and may
be added or deleted from specific vehicle models.
(1) The programmable electronic features that may
be provided on the vehicle are:
²Rolling Power Door Locks
²Horn Chirp (When Doors Locked With Remote
Keyless Entry)²Headlamp Flash (When Doors Locked or
Unlocked With Remote Keyless Entry)
²Low Fuel Chime
²Remote Keyless Entry Door Unlock Sequence
²Headlights On Automatically With Wipers
²Turn Signal Chime
²12V Power Outlet
²Remote Unlock
²Remote Linked To Memory
²Headlamp Delay
²Service Interval
²Easy Exit Seat
(2) Programming any of the above features is to be
performed prior to vehicle delivery to the customer,
depending on customer preference.
NOTE: For all vehicles except Caravan/Town and
Country, the programming must be performed using
the DRB IIITscan tool. On Caravan/Town and Coun-
try vehicles the features can be programmed using
the DRB IIITscan tool or by button pushing
sequences. The customer can perform program-
ming, if desired, by following the instructions out-
lined in the owner manual.
OPERATION
NOTE: The programmable features provided on
vehicles need to be explained to the customer at
the time of sale. The customer's preferences con-
cerning the features should be noted and pro-
grammed accordingly during predelivery.
NOTE: When using the DRB IIITscan tool to enable/
disable any programmable electronic features, go to
the main menu item #9 on the DRB IIITscan tool.
This is ªCustomer Preferencesº. You must choose
ªCustomer Preferencesº on the main menu to pro-
gram the desired features.
ROLLING POWER DOOR LOCKS
With this feature enabled, the vehicle's door lock-
ing mechanisms automatically lock when the vehicle
reaches approximately 24 Km/h (15 mph).
HORN CHIRP
NOTE: This feature can be enabled with or without
the headlamp flash feature.
The horn chirp function is a feature that can be
enabled or disabled on vehicles equipped with
30 - 20 NEW VEHICLE PREPARATIONBR/BE
PRE DELIVERY STORAGE (Continued)

Remote Keyless Entry (RKE). The horn chirps when
the vehicle is locked with the RKE transmitter.
HEADLAMP FLASH
NOTE: This feature can be enabled with or without
the horn chirp feature.
The headlamp flash function is a feature that can
be enabled or disabled on vehicles equipped with
Remote Keyless Entry (RKE). The headlamps flash
once when the vehicle is locked with the RKE trans-
mitter, and flash twice when the vehicle is unlocked
with the RKE transmitter.
LOW FUEL CHIME
All vehicles equipped with the audible low fuel
chime are shipped with this feature enabled.
REMOTE KEYLESS ENTRY (RKE) DOOR UNLOCK
SEQUENCE
Two door unlock sequences are provided on vehi-
cles equipped with this feature. When using the RKE
transmitter to unlock the doors, pressing the unlock
button once when the feature is enabled unlocks only
the driver's door. Pushing the RKE transmitter
unlock button a second time unlocks the remaining
doors. When the RKE door unlock feature is disabled,
all doors unlock with one press of the RKE transmit-
ter unlock button.
HEADLIGHTS ON AUTOMATICALLY WITH WIPERS
This feature appears on vehicles that have, as an
option, automatic headlights. When the windshield
wipers are turned on, the headlights automatically
turn on.
12V POWER OUTLET
This feature currently appears on Caravan/Voyag-
er/Town and Country vehicles. The vehicles are
shipped with the 12V power outlets turned off with
the ignition key. The relay can be changed to make
the outlets powered at all times. This feature may be
of interest to customers with cell phones.
TURN SIGNAL CHIME
This feature is an audible turn signal warning
chime. The chime sounds if the turn signal is on, the
vehicle has traveled one mile and vehicle speed has
exceeded 40 Km/h (25 mph).
REMOTE UNLOCK
The remote unlock function is a feature that can be
enabled or disabled on vehicles equipped with
Remote Keyless Entry (RKE). With the first press of
the RKE transmitter to unlock the doors, the driver's
door only unlocks. With the second press of the RKEtransmitter, the remaining doors and the liftgate
unlock. With the remote unlock feature enabled, the
first press of the RKE transmitter unlocks all doors.
REMOTE LINKED TO MEMORY
The remote linked to memory function is currently
only available only on Jeep Grand Cherokee Limited
vehicles. When enabled, this feature recalls a mem-
ory of seats, mirror and radio presets and positions
when unlocking the vehicle with the RKE transmit-
ter.
HEADLAMP DELAY
Currently available only on Jeep Grand Cherokee
vehicles, the headlamp delay timeout can be set to
30, 60 or 90 seconds. This timeout only occurs when
the ignition is turned off prior to turning the head-
lamps off, or when leaving the headlamps in AUTO
mode.
SERVICE INTERVAL
Currently available only on Jeep Grand Cherokee
vehicles, the interval for the service reminder mes-
sage can be set from 3,219 kilometers to 12,070 kilo-
meters (2,000 miles to 7,500 miles).
EASY EXIT SEAT
Currently available only on Jeep Grand Cherokee
Limited vehicles, the driver's seat will reposition
55mm (2.1 inches) rearward, or the end of travel if
less than 55mm (2.1 inches) and full downward when
the key is removed from the ignition. This feature
allows ease of exiting the vehicle. The seat will repo-
sition itself to the memory location when the vehicle
is unlocked using the RKE transmitter or by pressing
the memory buttons on the door panel.
APPEARANCE TIPS
CLEANING
(1) Before delivering the new vehicle to the cus-
tomer, the following checks on appearance details are
recommended:
²Wash the vehicle to remove all traces of road
grime and other dirt on the car from new vehicle
preparation operations
²Clean the tire sidewalls
²Clean exterior and interior glass surfaces
²Remove all protective covers
²Remove undercoat overspray, excess window
sealer, and excess weatherstrip adhesive
²Inspect interior trim, seats, carpeting, and mold-
ings. Clean as necessary
²Remove shipping and inspection stickers
BR/BENEW VEHICLE PREPARATION 30 - 21
PROGRAMMABLE ELECTRONIC FEATURES (Continued)

AIR PUMP FILTER - INSTALLATION......25-29
AIR PUMP FILTER - REMOVAL..........25-29
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-490,21-661
AIR TO OIL COOLER - INSTALLATION.....7-88
AIR TO OIL COOLER - REMOVAL.........7-87
AIRBAG - ASSEMBLY, DRIVER..........8O-17
AIRBAG - DESCRIPTION, DRIVER........8O-14
AIRBAG - DESCRIPTION, PASSENGER....8O-21
AIRBAG - DISASSEMBLY, DRIVER.......8O-15
AIRBAG - INSTALLATION, DRIVER.......8O-18
AIRBAG - INSTALLATION, PASSENGER . . . 8O-23
AIRBAG - OPERATION, DRIVER.........8O-14
AIRBAG - OPERATION, PASSENGER......8O-21
AIRBAG - REMOVAL, DRIVER...........8O-14
AIRBAG - REMOVAL, PASSENGER.......8O-21
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-6
AIRBAG CONTROL MODULE -
INSTALLATION.......................8O-8
AIRBAG CONTROL MODULE -
OPERATION..........................8O-6
AIRBAG CONTROL MODULE - REMOVAL . . . 8O-7
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-4
AIRBAG INDICATOR - DESCRIPTION......8J-15
AIRBAG INDICATOR - OPERATION.......8J-15
AIRBAG ON/OFF SWITCH -
DESCRIPTION, PASSENGER............8O-23
AIRBAG ON/OFF SWITCH -
INSTALLATION, PASSENGER...........8O-25
AIRBAG ON/OFF SWITCH - OPERATION,
PASSENGER........................8O-24
AIRBAG ON/OFF SWITCH - REMOVAL,
PASSENGER........................8O-24
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-4
AIRBAG SYSTEM - SPECIAL TOOLS.......8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED.............8O-4
AIRFLOW - DESCRIPTION, HVAC
SYSTEM............................24-31
AJAR SWITCH - DESCRIPTION, DOOR....8L-34
AJAR SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8L-34
AJAR SWITCH - INSTALLATION, DOOR . . . 8L-35
AJAR SWITCH - REMOVAL, DOOR.......8L-35
ALIGNMENT - DESCRIPTION, WHEEL.......2-1
ALIGNMENT - OPERATION, WHEEL........2-2
ALIGNMENT I.F.S. - STANDARD
PROCEDURES.........................2-2
ALIGNMENT LINK/COIL SUSPENSION -
STANDARD PROCEDURES...............2-5
ALIGNMENT, SPECIAL TOOLS -
HEADLAMP..........................8L-4
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD
PROCEDURE.....21-159,21-330,21-502,21-673
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-11
AMBIENT TEMP SENSOR -
INSTALLATION......................8M-13
AMBIENT TEMP SENSOR - OPERATION . . 8M-11
AMBIENT TEMP SENSOR - REMOVAL
....8M-12
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS & TESTING
...............8M-12
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-10
AN AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER
...........8O-4
ANTENNA - DIAGNOSIS AND TESTING
.....8A-5
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE - OPERATION
. . . 8A-4
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL
.................8A-10
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL
..................8A-9
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
.......................8E-12
ANTILOCK BRAKE - OPERATION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - REMOVAL,
CONTROLLER
.......................8E-12A-PILLAR GRAB HANDLE -
INSTALLATION......................23-119
A-PILLAR GRAB HANDLE - REMOVAL . . . 23-119
A-PILLAR TRIM - INSTALLATION.......23-119
A-PILLAR TRIM - REMOVAL...........23-119
A-PILLAR TWEETER SPEAKER -
INSTALLATION.......................8A-19
A-PILLAR TWEETER SPEAKER -
REMOVAL..........................8A-19
APPEARANCE TIPS - CLEANING.........30-21
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-8
APPLIQUE - INSTALLATION........23-62,23-67
APPLIQUE - REMOVAL...........23-62,23-67
AREA LEAKS - DIAGNOSIS AND
TESTING, REAR SEAL..................9-10
ARM / ADJUSTER ASSEMBLY -
INSTALLATION, ROCKER................9-85
ARM / ADJUSTER ASSEMBLY -
REMOVAL, ROCKER...................9-85
ARM / ADJUSTER ASSY - CLEANING,
ROCKER............................9-262
ARM / ADJUSTER ASSY - DESCRIPTION,
ROCKER............................9-261
ARM / ADJUSTER ASSY - INSPECTION,
ROCKER............................9-262
ARM / ADJUSTER ASSY -
INSTALLATION, ROCKER.....9-142,9-200,9-263
ARM / ADJUSTER ASSY - REMOVAL,
ROCKER.................9-142,9-200,9-261
ARM - DESCRIPTION, WIPER...........8R-11
ARM - INSTALLATION, LOWER
CONTROL.......................2-10,2-20
ARM - INSTALLATION, UPPER
CONTROL.......................2-13,2-24
ARM - INSTALLATION, WIPER..........8R-12
ARM - OPERATION, WIPER............8R-12
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-20
ARM - REMOVAL, UPPER CONTROL . . 2-13,2-23
ARM - REMOVAL, WIPER..............8R-12
ARMREST/CONSOLE - INSTALLATION,
CENTER SEAT......................23-132
ARMREST/CONSOLE - REMOVAL,
CENTER SEAT......................23-132
ARMREST/LATCH COVER -
INSTALLATION, CENTER SEAT.........23-132
ARMREST/LATCH COVER - REMOVAL,
CENTER SEAT......................23-132
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-3
ASD SENSE - PCM INPUT - OPERATION....8I-3
ASH RECEIVER - INSTALLATION........23-109
ASH RECEIVER - REMOVAL...........23-108
ASSEMBLE, OIL PUMP...........9-109,9-165
ASSEMBLY - INSTALLATION, ROCKER
ARM / ADJUSTER.....................9-85
ASSEMBLY - REMOVAL, ROCKER ARM /
ADJUSTER...........................9-85
ASSEMBLY, AUTOMATIC
TRANSMISSION - 42RE...............21-166
ASSEMBLY, AUTOMATIC
TRANSMISSION - 44RE...............21-337
ASSEMBLY, AUTOMATIC
TRANSMISSION - 46RE...............21-510
ASSEMBLY, AUTOMATIC
TRANSMISSION - 47RE...............21-681
ASSEMBLY, AXLE VACUUM MOTOR . . . 3-33,3-65
ASSEMBLY, DIFFERENTIAL . . . 3-128,3-159,3-188,
3-37,3-69,3-98
ASSEMBLY, DIFFERENTIAL - POWR-LOK . . 3-163
ASSEMBLY, DIFFERENTIAL - TRAC-LOK . . . 3-101,
3-132,3-190
ASSEMBLY, DISC BRAKE CALIPERS.......5-12
ASSEMBLY, DRIVER AIRBAG...........8O-17
ASSEMBLY, FLYWHEEL.................6-17
ASSEMBLY, FRONT CLUTCH.....21-206,21-376,
21-550,21-721
ASSEMBLY, FRONT SERVO......21-208,21-379,
21-553,21-723
ASSEMBLY, GLOVE BOX..............23-112
ASSEMBLY, HVAC HOUSING............24-36
ASSEMBLY, INSTRUMENT CLUSTER......8J-13
ASSEMBLY, MANUAL - NV3500
.........21-17
ASSEMBLY, MANUAL - NV4500
.........21-65
ASSEMBLY, MANUAL - NV5600
........21-110
ASSEMBLY, OIL PUMP
.................9-51
ASSEMBLY, OIL PUMP
. . . 21-212,21-382,21-558,
21-729ASSEMBLY, OVERDRIVE UNIT . . . 21-225,21-395,
21-569,21-742
ASSEMBLY, OVERHEAD CONSOLE -
OVERHEAD CONSOLE.................8M-7
ASSEMBLY, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON
RETAINER.......21-236,21-406,21-581,21-752
ASSEMBLY, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-412,21-588,21-760
ASSEMBLY, REAR CLUTCH......21-248,21-419,
21-593,21-766
ASSEMBLY, REAR SERVO.......21-251,21-422,
21-595,21-768
ASSEMBLY, TRANS COOLER -
3.9L/5.2L/5.9L........................7-82
ASSEMBLY, TRANSFER CASE - NV231HD . 21-834
ASSEMBLY, TRANSFER CASE - NV241HD . 21-904
ASSEMBLY, TRANSFER CASE - NV241LD . 21-869
ASSEMBLY, VALVE BODY . 21-294,21-466,21-638,
21-810
ASSEMBLY, WHEEL CYLINDERS..........5-31
ASSIST HANDLE - INSTALLATION.......23-124
ASSIST HANDLE - REMOVAL..........23-124
ASSY - CLEANING, ROCKER ARM /
ADJUSTER..........................9-262
ASSY - DESCRIPTION, ROCKER ARM /
ADJUSTER..........................9-261
ASSY - INSPECTION, ROCKER ARM /
ADJUSTER..........................9-262
ASSY - INSTALLATION, ROCKER ARM /
ADJUSTER................9-142,9-200,9-263
ASSY - REMOVAL, ROCKER ARM /
ADJUSTER................9-142,9-200,9-261
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-2
AUDIO SYSTEMS, SPECIAL TOOLS.......8A-4
AUGAT - INSTALLATION, CONNECTOR . . 8W-01-8
AUGAT - REMOVAL, CONNECTOR.....8W-01-8
AUTO. TRANS. - INSTALLATION, DIESEL
WITH..........................8P-11,8P-4
AUTO. TRANS. - REMOVAL, DIESEL
WITH...........................8P-4,8P-8
AUTOMATIC DAY / NIGHT MIRROR -
DESCRIPTION.......................8N-10
AUTOMATIC DAY / NIGHT MIRROR -
INSTALLATION......................8N-12
AUTOMATIC DAY / NIGHT MIRROR -
OPERATION.........................8N-11
AUTOMATIC DAY / NIGHT MIRROR -
REMOVAL..........................8N-12
AUTOMATIC DAY/NIGHT MIRROR -
DIAGNOSIS AND TESTING.............8N-11
AUTOMATIC SHUT DOWN RELAY -
INSTALLATION........................8I-5
AUTOMATIC SHUT DOWN RELAY -
REMOVAL............................8I-4
AUTOMATIC TRANSMISSION - 42RE -
ASSEMBLY.........................21-166
AUTOMATIC TRANSMISSION - 42RE -
CLEANING.........................21-165
AUTOMATIC TRANSMISSION - 42RE -
DESCRIPTION
......................21-135
AUTOMATIC TRANSMISSION - 42RE -
DISASSEMBLY
......................21-160
AUTOMATIC TRANSMISSION - 42RE -
INSPECTION
.......................21-165
AUTOMATIC TRANSMISSION - 42RE -
INSTALLATION
......................21-173
AUTOMATIC TRANSMISSION - 42RE -
OPERATION
........................21-137
AUTOMATIC TRANSMISSION - 42RE -
REMOVAL
.........................21-159
AUTOMATIC TRANSMISSION - 44RE -
ASSEMBLY
.........................21-337
AUTOMATIC TRANSMISSION - 44RE -
CLEANING
.........................21-336
AUTOMATIC TRANSMISSION - 44RE -
DESCRIPTION
......................21-306
AUTOMATIC TRANSMISSION - 44RE -
DISASSEMBLY
......................21-331
AUTOMATIC TRANSMISSION - 44RE -
INSPECTION
.......................21-337
AUTOMATIC TRANSMISSION - 44RE -
INSTALLATION
......................21-344
AUTOMATIC TRANSMISSION - 44RE -
OPERATION
........................21-308
2 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

BEARING FITTING, CONNECTING ROD
BEARINGS - STANDARD PROCEDURE-
CONNECTING ROD....................9-31
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN..........9-146,9-32,9-90
BEARINGS - INSTALLATION, AXLE . . 3-125,3-156,
3-185,3-95
BEARINGS - INSTALLATION, CAMSHAFT . . 9-144,
9-201,9-273,9-29,9-87
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN.....9-147,9-204,9-34,9-90
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE . . 3-103,3-134,3-164,3-192,
3-39,3-71
BEARINGS - OPERATION, CRANKSHAFT
MAIN......................9-146,9-32,9-90
BEARINGS - REMOVAL, AXLE.....3-125,3-156,
3-185,3-94
BEARINGS - REMOVAL, CAMSHAFT.....9-143,
9-200,9-268,9-29,9-86
BEARINGS - REMOVAL, CRANKSHAFT
MAIN.................9-147,9-204,9-33,9-90
BEARINGS - REMOVAL, DIFFERENTIAL
CASE.......3-103,3-134,3-164,3-192,3-39,3-71
BEARINGS - STANDARD PROCEDURE-
CONNECTING ROD BEARING FITTING,
CONNECTING ROD....................9-31
BEARINGS (IN BLOCK) - INSPECTION,
CAMSHAFT.........................9-272
BED GROUND STRAP - INSTALLATION,
CAB-TO............................8A-14
BED GROUND STRAP - REMOVAL,
CAB-TO............................8A-14
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING. . . 9-113,9-169,9-226,9-56
BELT / CHAIN COVER(S) - REMOVAL,
TIMING..............9-113,9-169,9-225,9-56
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE............7-24,7-27,7-31
BELT & RETRACTOR - INSTALLATION,
REAR SEAT.........................8O-26
BELT & RETRACTOR - REMOVAL, REAR
SEAT ..............................8O-26
BELT BUCKLE - INSTALLATION, FRONT
SEAT ..............................8O-20
BELT BUCKLE - INSTALLATION, REAR
SEAT ..............................8O-27
BELT BUCKLE - REMOVAL, FRONT SEAT . . 8O-20
BELT BUCKLE - REMOVAL, REAR SEAT . . . 8O-27
BELT SWITCH - DESCRIPTION, SEAT.....8O-28
BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT......................8O-28
BELT SWITCH - OPERATION, SEAT.......8O-28
BELT TENSIONERS - 3.9L/5.2L/5.9L -
DESCRIPTION........................7-19
BELT TENSIONERS - 3.9L/5.2L/5.9L -
INSTALLATION........................7-20
BELT TENSIONERS - 3.9L/5.2L/5.9L -
OPERATION..........................7-19
BELT TENSIONERS - 3.9L/5.2L/5.9L -
REMOVAL...........................7-20
BELT TENSIONERS - 5.9L DIESEL -
DESCRIPTION........................7-23
BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION
........................7-23
BELT TENSIONERS - 5.9L DIESEL -
OPERATION
..........................7-23
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL
...........................7-23
BELT TENSIONERS - 8.0L -
DESCRIPTION
........................7-20
BELT TENSIONERS - 8.0L -
INSTALLATION
........................7-22
BELT TENSIONERS - 8.0L - OPERATION
....7-20
BELT TENSIONERS - 8.0L - REMOVAL
.....7-21
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT
.................8O-29
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT
.....................8O-29
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR INNER
.................23-154
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR OUTER
................23-154
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR INNER
.................23-154
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR OUTER
................23-154BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING . 9-115,9-170,9-227,9-58
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING.....9-114,9-170,9-226,9-57
BELT/CHAIN TENSIONER - DESCRIPTION,
TIMING.............................9-57
BELT/CHAIN TENSIONER - OPERATION,
TIMING.............................9-57
BELTS - 3.9L/5.2L/5.9L - INSTALLATION,
DRIVE..............................7-27
BELTS - 3.9L/5.2L/5.9L - REMOVAL,
DRIVE..............................7-26
BELTS - 5.9L DIESEL - INSTALLATION,
DRIVE..............................7-34
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-33
BELTS - 8.0L - INSTALLATION, DRIVE.....7-30
BELTS - 8.0L - REMOVAL, DRIVE.........7-30
BELTS, RETRACTORS AND HEAD
RESTRAINTS - INSPECTION, SEAT
BELTS, SHOULDER...................30-12
BELTS, SHOULDER BELTS, RETRACTORS
AND HEAD RESTRAINTS -
INSPECTION, SEAT...................30-12
BENCH - INSTALLATION, SEAT - SPLIT . . 23-134
BENCH - INSTALLATION, SEAT BACK -
SPLIT.............................23-136
BENCH - INSTALLATION, SEAT BACK
COVER - SPLIT.....................23-138
BENCH - INSTALLATION, SEAT CUSHION
COVER - SPLIT.....................23-140
BENCH - INSTALLATION, SEAT TRACK -
SPLIT.............................23-142
BENCH - REMOVAL, SEAT - SPLIT........23-134
BENCH - REMOVAL, SEAT BACK - SPLIT . 23-135
BENCH - REMOVAL, SEAT BACK COVER
- SPLIT...........................23-137
BENCH - REMOVAL, SEAT CUSHION
COVER - SPLIT.....................23-139
BENCH - REMOVAL, SEAT TRACK -
SPLIT.............................23-142
BENCH SEAT - INSTALLATION, SEAT....23-133
BENCH SEAT - INSTALLATION, SEAT
BACK.............................23-135
BENCH SEAT - REMOVAL, SEAT........23-133
BENCH SEAT - REMOVAL, SEAT BACK . . . 23-135
BETTS - INSTALLATION, CONNECTOR -
THOMAS........................8W-01-10
BETTS - REMOVAL, CONNECTOR -
THOMAS.........................8W-01-9
BEZEL - INSTALLATION, CLUSTER......23-110
BEZEL - REMOVAL, CLUSTER..........23-109
BIN - INSTALLATION, CUBBY..........23-110
BIN - INSTALLATION, STORAGE........23-116
BIN - REMOVAL, CUBBY..............23-110
BIN - REMOVAL, STORAGE............23-116
BLADE - DESCRIPTION, WIPER.........8R-12
BLADE - INSTALLATION, WIPER.........8R-13
BLADE - OPERATION, WIPER...........8R-13
BLADE - REMOVAL, WIPER............8R-13
BLEED - STANDARD PROCEDURE, AIR....14-57
BLEEDING - STANDARD PROCEDURE......5-19
BLEEDING - STANDARD PROCEDURE,
MANUAL.............................5-7
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...................5-30
BLEEDING - STANDARD PROCEDURE,
PRESSURE...........................5-8
BLEND DOOR - INSTALLATION
..........24-38
BLEND DOOR - REMOVAL
.............24-38
BLEND DOOR ACTUATOR -
INSTALLATION
.......................24-26
BLEND DOOR ACTUATOR - REMOVAL
....24-25
BLOCK - CLEANING, ENGINE
. . 9-142,9-200,9-28,
9-86
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR
...................24-23
BLOCK - DESCRIPTION, JUNCTION
....8W-97-6
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR
............24-24
BLOCK - INSPECTION, ENGINE
....9-142,9-200,
9-267,9-28,9-86
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR
...................24-24
BLOCK - INSTALLATION, JUNCTION
....8W-97-7
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR
..........................24-23
BLOCK - OPERATION, JUNCTION
......8W-97-6BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-24
BLOCK - REMOVAL, JUNCTION.......8W-97-6
BLOCK - STANDARD PROCEDURE-
CYLINDER BLOCK REFACING, ENGINE....9-263
BLOCK HEATER - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE.................7-45
BLOCK HEATER - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE................7-45
BLOCK HEATER - 3.9L/5.2L/5.9L -
OPERATION, ENGINE...................7-45
BLOCK HEATER - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE....................7-45
BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-47
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE................7-47
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE...................7-47
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE....................7-47
BLOCK HEATER - 8.0L - DESCRIPTION,
ENGINE.............................7-46
BLOCK HEATER - 8.0L - INSTALLATION,
ENGINE.............................7-46
BLOCK HEATER - 8.0L - OPERATION,
ENGINE.............................7-46
BLOCK HEATER - 8.0L - REMOVAL,
ENGINE.............................7-46
BLOCK REFACING, ENGINE BLOCK -
STANDARD PROCEDURE-CYLINDER......9-263
BLOWER MOTOR - DESCRIPTION.......24-32
BLOWER MOTOR - DIAGNOSIS AND
TESTING...........................24-33
BLOWER MOTOR - INSTALLATION.......24-33
BLOWER MOTOR - OPERATION.........24-32
BLOWER MOTOR - REMOVAL...........24-33
BLOWER MOTOR RELAY - DESCRIPTION . . 24-22
BLOWER MOTOR RELAY - DIAGNOSIS
AND TESTING.......................24-22
BLOWER MOTOR RELAY -
INSTALLATION.......................24-23
BLOWER MOTOR RELAY - OPERATION . . . 24-22
BLOWER MOTOR RELAY - REMOVAL.....24-23
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-23
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-24
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-24
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-23
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-24
BLOWER MOTOR SWITCH -
DESCRIPTION.......................24-24
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING.......................24-25
BLOWER MOTOR SWITCH - OPERATION . . 24-25
BLOWER MOTOR SWITCH - REMOVAL . . . 24-25
BODY - ADJUSTMENTS, VALVE . . 21-304,21-476,
21-646,21-818
BODY - ASSEMBLY, VALVE......21-294,21-466,
21-638,21-810
BODY & CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
BODY - CLEANING, VALVE......21-293,21-465,
21-637,21-808
BODY - DESCRIPTION, THROTTLE.......14-48
BODY - DESCRIPTION, VALVE . . . 21-263,21-433,
21-607,21-780
BODY - DISASSEMBLY, VALVE . . . 21-282,21-453,
21-626,21-799
BODY - INSPECTION, VALVE....21-293,21-465,
21-637,21-809
BODY - INSTALLATION, VALVE . . . 21-303,21-475,
21-645,21-818
BODY - OPERATION, THROTTLE.........14-48
BODY - OPERATION, VALVE
.....21-267,21-438,
21-611,21-783
BODY - REMOVAL, VALVE
......21-281,21-452,
21-625,21-798
BODY - SAFETY PRECAUTIONS AND
WARNINGS
..........................23-1
BODY CODE PLATE - DESCRIPTION
.....Intro.-1
BODY CONTROL/CENTRAL TIMER
MODULE - DESCRIPTION
...............8E-1
4 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

BODY CONTROL/CENTRAL TIMER
MODULE - INSTALLATION...............8E-6
BODY CONTROL/CENTRAL TIMER
MODULE - OPERATION.................8E-3
BODY CONTROL/CENTRAL TIMER
MODULE - REMOVAL..................8E-5
BODY GAP AND FLUSH
MEASUREMENTS, SPECIFICATIONS......23-56
BODY OPENING DIMENSIONS,
SPECIFICATIONS.....................23-60
BODY SEALER LOCATIONS,
SPECIFICATIONS.....................23-47
BODY SEALING - INSPECTION..........30-10
BODY SIDE MOLDINGS - INSTALLATION . . 23-87
BODY SIDE MOLDINGS - REMOVAL......23-87
BODY STRIPES AND DECALS -
INSTALLATION.......................23-87
BODY STRIPES AND DECALS -
REMOVAL..........................23-87
BODY VENT - INSTALLATION..........23-126
BODY VENT - REMOVAL..............23-126
BOOST PRESSURE - DIAGNOSIS AND
TESTING...........................14-89
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-17
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-29
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-20
BOOSTER - REMOVAL, POWER BRAKE....5-19
BOOT - INSTALLATION, 4WD FLOOR
SHIFT..............................23-122
BOOT - MANUAL TRANSMISSION -
INSTALLATION, SHIFT................23-122
BOOT - MANUAL TRANSMISSION -
REMOVAL, SHIFT....................23-122
BOOT - REMOVAL, 4WD FLOOR SHIFT . . . 23-122
BORE, DE-GLAZE - STANDARD
PROCEDURE-CYLINDER...............9-264
BORE HONING - STANDARD
PROCEDURE, CYLINDER . . 9-10,9-126,9-180,9-69
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-267
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-265
BOX - ASSEMBLY, GLOVE.............23-112
BOX - DISASSEMBLY, GLOVE..........23-112
BOX - INSTALLATION, CARGO..........23-97
BOX - INSTALLATION, GLOVE..........23-113
BOX - REMOVAL, CARGO..............23-96
BOX - REMOVAL, GLOVE.............23-112
BOX LAMP AND SWITCH -
INSTALLATION, GLOVE................8L-35
BOX LAMP AND SWITCH - REMOVAL,
GLOVE.............................8L-35
BOX LATCH STRIKER - INSTALLATION,
GLOVE............................23-113
BOX LATCH STRIKER - REMOVAL,
GLOVE............................23-113
BOX OPENING UPPER TRIM -
INSTALLATION, GLOVE...............23-114
BOX OPENING UPPER TRIM - REMOVAL,
GLOVE............................23-114
B-PILLAR DOOR SEAL - INSTALLATION . . 23-152
B-PILLAR DOOR SEAL - REMOVAL......23-152
B-PILLAR TRIM - INSTALLATION
.......23-120
B-PILLAR TRIM - REMOVAL
...........23-120
BR PAINT COLOR CODES,
SPECIFICATIONS - 2001
..............23-129
BRACKET - INSTALLATION, CAB
CHASSIS ADAPTER
....................13-9
BRACKET - INSTALLATION, REARVIEW
MIRROR SUPPORT
..................23-126
BRACKET - REMOVAL, CAB CHASSIS
ADAPTER
............................13-9
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK
..........................8E-11
BRAKE - INSPECTION, PARKING
.........30-17
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK
..........................8E-12
BRAKE - OPERATION, CONTROLLER
ANTILOCK
..........................8E-11
BRAKE - REMOVAL, CONTROLLER
ANTILOCK
..........................8E-12
BRAKE BOOSTER - INSTALLATION,
POWER
.............................5-20
BRAKE BOOSTER - REMOVAL, POWER
....5-19BRAKE CABLE - 2500/3500 WITH REAR
DISC BRAKES - INSTALLATION, REAR
PARK...............................5-38
BRAKE CABLE - 2500/3500 WITH REAR
DISC BRAKES - REMOVAL, REAR
PARK...............................5-37
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-39
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-37
BRAKE CABLE 2500/3500 SERIES WITH
DRUM BRAKES - INSTALLATION, REAR
PARK...............................5-39
BRAKE CABLES - 1500 SERIES -
INSTALLATION, REAR PARK.............5-39
BRAKE CABLES - 1500 SERIES -
REMOVAL, REAR PARK.................5-37
BRAKE CABLES 2500/3500 SERIES WITH
DRUM BRAKES - REMOVAL, REAR
PARK...............................5-38
BRAKE CALIPERS - ASSEMBLY, DISC......5-12
BRAKE CALIPERS - CLEANING, DISC......5-12
BRAKE CALIPERS - DISASSEMBLY, DISC . . . 5-11
BRAKE CALIPERS - INSPECTION, DISC....5-12
BRAKE DRUM - ADJUSTMENT, REAR......5-34
BRAKE DRUM - DIAGNOSIS AND
TESTING............................5-33
BRAKE DRUM MACHINING - STANDARD
PROCEDURE.........................5-33
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-14
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-14
BRAKE FLUID, SPECIFICATIONS..........5-15
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-16
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-16
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-16
BRAKE LAMP SWITCH - DESCRIPTION....8L-4
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING........................8L-5
BRAKE LAMP SWITCH - INSTALLATION....8L-5
BRAKE LAMP SWITCH - OPERATION......8L-4
BRAKE LAMP SWITCH - REMOVAL.......8L-5
BRAKE ROTOR - DIAGNOSIS AND
TESTING, DISC.......................5-20
BRAKE SHOES - 2500/3500 -
INSTALLATION, REAR DRUM IN HAT
PARK...............................5-42
BRAKE SHOES - 2500/3500 - REMOVAL,
REAR DRUM IN HAT PARK..............5-41
BRAKE SHOES-11 INCH - INSTALLATION,
REAR...............................5-27
BRAKE SHOES-11 INCH - REMOVAL,
REAR...............................5-25
BRAKE, SPECIFICATIONS - BASE..........5-2
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-5
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION
.......................8J-16
BRAKE/PARK BRAKE INDICATOR -
OPERATION
.........................8J-16
BRAKES - DESCRIPTION, 2500/3500
WITH REAR DISC
.....................5-35
BRAKES - INSPECTION, SERVICE
........30-17
BRAKES - INSTALLATION, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR DISC
..........................5-38
BRAKES - INSTALLATION, REAR PARK
BRAKE CABLE 2500/3500 SERIES
WITH DRUM
.........................5-39
BRAKES - OPERATION, 2500/3500 WITH
REAR DISC
..........................5-36
BRAKES - REMOVAL, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR DISC
..........................5-37
BRAKES - REMOVAL, REAR PARK
BRAKE CABLES 2500/3500 SERIES
WITH DRUM
.........................5-38
BRAKES, SPECIAL TOOLS - BASE
.........5-4
BREAKER - DESCRIPTION, CIRCUIT
....8W-97-4
BREAKER - DIAGNOSIS & TESTING,
CIRCUIT
.........................8W-97-4
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH
............24-13BREATHER VAPOR CANISTER -
INSTALLATION, CRANKCASE............9-242
BREATHER VAPOR CANISTER -
REMOVAL, CRANKCASE...............9-241
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-20
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-27
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-20
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-27
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-11
BUMPER - DESCRIPTION, JOUNCE....2-28,2-9
BUMPER - INSTALLATION, FRONT........13-4
BUMPER - INSTALLATION, REAR.........13-5
BUMPER - INSTALLATION, SLAM........23-66
BUMPER - OPERATION, JOUNCE......2-28,2-9
BUMPER - REMOVAL, FRONT............13-3
BUMPER - REMOVAL, REAR.............13-5
BUMPER - REMOVAL, SLAM...........23-66
BUMPERS - DESCRIPTION..............13-1
BUMPER-SPORT - INSTALLATION,
FRONT..............................13-4
BUMPER-SPORT - REMOVAL, FRONT......13-4
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF . . . 21-199,21-370,21-545,
21-715
BUS - DESCRIPTION, CCD DATA..........8E-6
BUS - DIAGNOSIS AND TESTING, CCD
D ATA................................8E-11
BUS - OPERATION, CCD DATA...........8E-7
BUSHING - INSTALLATION,
DISTRIBUTOR...............9-150,9-37,9-94
BUSHING - INSTALLATION, EXTENSION
HOUSING........21-198,21-369,21-544,21-714
BUSHING - REMOVAL, DISTRIBUTOR....9-150,
9-37,9-94
BUSHING - REMOVAL, EXTENSION
HOUSING........21-198,21-369,21-544,21-714
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING....21-850,21-885,21-921
BUSHING AND SEAL - REMOVAL,
EXTENSION HOUSING....21-850,21-885,21-921
BUSHINGS - INSTALLATION.............2-28
BUSHINGS - REMOVAL.................2-28
BYPASS HOSE WITH AIR CONDITIONING
- INSTALLATION, WATER PUMP..........7-77
BYPASS HOSE WITH AIR CONDITIONING
- REMOVAL, WATER PUMP..............7-74
BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER PUMP........................7-78
BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER
PUMP..............................7-77
CAB - INSTALLATION, CLUB/QUAD.......8O-20
CAB - INSTALLATION, STANDARD.......8O-19
CAB - REMOVAL, CLUB/QUAD..........8O-19
CAB - REMOVAL, STANDARD...........8O-18
CAB CHASSIS ADAPTER BRACKET -
INSTALLATION........................13-9
CAB CHASSIS ADAPTER BRACKET -
REMOVAL...........................13-9
CAB SIDE PANEL SPEAKER -
INSTALLATION, REAR.................8A-21
CAB SIDE PANEL SPEAKER - REMOVAL,
REAR..............................8A-20
CABLE - 2500/3500 WITH REAR DISC
BRAKES - INSTALLATION, REAR PARK
BRAKE..............................5-38
CABLE - 2500/3500 WITH REAR DISC
BRAKES - REMOVAL, REAR PARK
BRAKE..............................5-37
CABLE - ADJUSTMENTS,
TRANSMISSION THROTTLE VALVE.....21-254,
21-425,21-598,21-771
CABLE - DESCRIPTION.................8P-4
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DESCRIPTION, BATTERY........8F-19
CABLE - DESCRIPTION, SPARK PLUG.....8I-19
CABLE - DESCRIPTION, THROTTLE
VALVE
..........21-253,21-424,21-597,21-770
CABLE - INSTALLATION, CHECK
.........23-63
CABLE - INSTALLATION, FRONT
PARKING BRAKE
......................5-39
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA
.....................8A-10
CABLE - INSTALLATION, LATCH RELEASE
. 23-101
BR/BEINDEX 5
Description Group-Page Description Group-Page Description Group-Page

CABLE - INSTALLATION, RELEASE.......23-83
CABLE - INSTALLATION, SPARK PLUG....8I-20
CABLE - INSTALLATION, THROTTLE
CONTROL....................14-105,14-50
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - OPERATION, BATTERY..........8F-20
CABLE - OPERATION, SPARK PLUG.......8I-19
CABLE - REMOVAL, CHECK.............23-62
CABLE - REMOVAL, FRONT PARKING
BRAKE..............................5-37
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-9
CABLE - REMOVAL, LATCH RELEASE....23-101
CABLE - REMOVAL, RELEASE...........23-82
CABLE - REMOVAL, SPARK PLUG........8I-20
CABLE - REMOVAL, THROTTLE
CONTROL....................14-104,14-50
CABLE 2500/3500 SERIES WITH DRUM
BRAKES - INSTALLATION, REAR PARK
BRAKE..............................5-39
CABLE INSTALLATION, GASOLINE -
NEGATIVE..........................8F-24
CABLE INSTALLATION, GASOLINE -
POSITIVE...........................8F-23
CABLE ORDER, 8.0L V-10 ENGINE -
SPARK PLUG.........................8I-2
CABLE REMOVAL, GASOLINE -
NEGATIVE..........................8F-23
CABLE REMOVAL, GASOLINE - POSITIVE . . 8F-23
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-3
CABLE TENSIONER - ADJUSTMENT.......5-40
CABLES - 1500 SERIES - INSTALLATION,
REAR PARK BRAKE....................5-39
CABLES - 1500 SERIES - REMOVAL,
REAR PARK BRAKE....................5-37
CABLES - DIAGNOSIS & TESTING,
BATTERY...........................8F-20
CABLES - DIAGNOSIS AND TESTING,
SPARK PLUG........................8I-19
CABLES 2500/3500 SERIES WITH DRUM
BRAKES - REMOVAL, REAR PARK
BRAKE..............................5-38
CAB-TO- BED GROUND STRAP -
INSTALLATION.......................8A-14
CAB-TO- BED GROUND STRAP -
REMOVAL..........................8A-14
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-4
CALIPERS - ASSEMBLY, DISC BRAKE......5-12
CALIPERS - CLEANING, DISC BRAKE......5-12
CALIPERS - DISASSEMBLY, DISC BRAKE . . . 5-11
CALIPERS - INSPECTION, DISC BRAKE....5-12
CAM - DESCRIPTION, TURN SIGNAL
CANCEL............................8L-30
CAM - OPERATION, TURN SIGNAL
CANCEL............................8L-31
CAM BORE REPAIR - STANDARD
PROCEDURE........................9-267
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING
CLUTCH.........21-236,21-406,21-581,21-752
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING
CLUTCH.........21-236,21-406,21-580,21-752
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING
CLUTCH.........21-235,21-405,21-580,21-751
CAMSHAFT & BEARINGS (IN BLOCK) -
INSPECTION
........................9-272
CAMSHAFT - INSTALLATION
. 9-144,9-201,9-273,
9-29,9-87
CAMSHAFT - REMOVAL
. 9-143,9-201,9-268,9-29,
9-86
CAMSHAFT BEARINGS - INSTALLATION
. . 9-144,
9-201,9-273,9-29,9-87
CAMSHAFT BEARINGS - REMOVAL
. 9-143,9-200,
9-268,9-29,9-86CANCEL CAM - DESCRIPTION, TURN
SIGNAL............................8L-30
CANCEL CAM - OPERATION, TURN
SIGNAL............................8L-31
CANISTER - DESCRIPTION, VAPOR......25-37
CANISTER - INSTALLATION, CRANKCASE
BREATHER VAPOR...................9-242
CANISTER - INSTALLATION, VAPOR......25-38
CANISTER - OPERATION, VAPOR........25-37
CANISTER - REMOVAL, CRANKCASE
BREATHER VAPOR...................9-241
CANISTER - REMOVAL, VAPOR..........25-37
CAP - CLEANING, RADIATOR PRESSURE . . . 7-66
CAP - DESCRIPTION, FUEL FILLER.......25-33
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-65
CAP - DIAGNOSIS AND TESTING,
DISTRIBUTOR.......................8I-12
CAP - DIAGNOSIS AND TESTING,
RADIATOR...........................7-66
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-66
CAP - OPERATION, FUEL FILLER........25-33
CAP - OPERATION, RADIATOR
PRESSURE..........................7-65
CAP - REMOVAL/INSTALLATION, FUEL
FILLER.............................25-33
CAPACITIES, SPECIFICATIONS - FLUID......0-6
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP..................14-9
CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR.....7-66
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE.................3-11
CARDAN UNIVERSAL JOINTS -
INSTALLATION, SINGLE............3-34,3-66
CARDAN UNIVERSAL JOINTS -
REMOVAL, SINGLE................3-33,3-65
CAREFUL NEW VEHICLE PREPARATION -
DESCRIPTION, THE IMPORTANCE OF......30-1
CARGO BOX - INSTALLATION...........23-97
CARGO BOX - REMOVAL...............23-96
CARGO DOOR - ADJUSTMENT..........23-78
CARPETS AND FLOOR MATS -
INSTALLATION......................23-123
CARPETS AND FLOOR MATS - REMOVAL . 23-123
CARTRIDGE FUSE - DESCRIPTION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - INSTALLATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - OPERATION,
GENERATOR......................8W-97-4
CARTRIDGE FUSE - REMOVAL,
GENERATOR......................8W-97-4
CASE - DIAGNOSIS AND TESTING,
TRANSFER.............21-821,21-856,21-892
CASE - INSPECTION, TRANSMISSION/
TRANSFER..........................30-15
CASE - NV231HD - ASSEMBLY,
TRANSFER.........................21-834
CASE - NV231HD - CLEANING,
TRANSFER.........................21-831
CASE - NV231HD - DESCRIPTION,
TRANSFER.........................21-820
CASE - NV231HD - DISASSEMBLY,
TRANSFER.........................21-822
CASE - NV231HD - INSPECTION,
TRANSFER.........................21-832
CASE - NV231HD - INSTALLATION,
TRANSFER.........................21-847
CASE - NV231HD - OPERATION,
TRANSFER.........................21-820
CASE - NV231HD - REMOVAL,
TRANSFER.........................21-822
CASE - NV241HD - ASSEMBLY,
TRANSFER.........................21-904
CASE - NV241HD - CLEANING,
TRANSFER.........................21-902
CASE - NV241HD - DESCRIPTION,
TRANSFER
.........................21-890
CASE - NV241HD - DISASSEMBLY,
TRANSFER
.........................21-894
CASE - NV241HD - INSPECTION,
TRANSFER
.........................21-902
CASE - NV241HD - INSTALLATION,
TRANSFER
.........................21-919
CASE - NV241HD - OPERATION,
TRANSFER
.........................21-892CASE - NV241HD - REMOVAL,
TRANSFER.........................21-894
CASE - NV241LD - ASSEMBLY,
TRANSFER.........................21-869
CASE - NV241LD - CLEANING,
TRANSFER.........................21-866
CASE - NV241LD - DESCRIPTION,
TRANSFER.........................21-855
CASE - NV241LD - DISASSEMBLY,
TRANSFER.........................21-858
CASE - NV241LD - INSPECTION,
TRANSFER.........................21-867
CASE - NV241LD - INSTALLATION,
TRANSFER.........................21-882
CASE - NV241LD - OPERATION,
TRANSFER.........................21-855
CASE - NV241LD - REMOVAL,
TRANSFER.........................21-858
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE BEARINGS - REMOVAL,
DIFFERENTIAL . . . 3-103,3-134,3-164,3-192,3-39,
3-71
CASE FLUID - DESCRIPTION, TRANSFER....0-5
CASE, NV231HD - TRANSFER..........21-849
CASE, NV241HD - TRANSFER..........21-920
CASE, NV241LD - TRANSFER..........21-884
CASE SKID PLATE - INSTALLATION,
TRANSFER..........................13-11
CASE SKID PLATE - REMOVAL,
TRANSFER..........................13-11
CASE, SPECIFICATIONS - TRANSFER.....21-848,
21-883,21-919
CASTER CORRECTION MEASUREMENT -
STANDARD PROCEDURES...............2-3
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- DESCRIPTION.......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSPECTION........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- INSTALLATION......................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- OPERATION.........................11-5
CATALYTIC CONVERTER - 3.9L/5.2L/5.9L
- REMOVAL..........................11-5
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - DESCRIPTION..............11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSPECTION...............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - INSTALLATION.............11-7
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - OPERATION................11-6
CATALYTIC CONVERTER - 5.9L HEAVY
DUTY/8.0L - REMOVAL.................11-6
CATCH - INSPECTION, HOOD LATCH/
SAFETY.............................30-4
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
CAUTION, INTERIOR.................23-118
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-42
CCD DATA BUS - DESCRIPTION..........8E-6
CCD DATA BUS - DIAGNOSIS AND
TESTING...........................8E-11
CCD DATA BUS - OPERATION............8E-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-7
CENTER - INSTALLATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - OPERATION, POWER
DISTRIBUTION
....................8W-97-8
CENTER - REMOVAL, POWER
DISTRIBUTION
....................8W-97-8
CENTER BEARING - CENTER BEARING
ADJUSTMENT
........................3-10
CENTER BEARING - DESCRIPTION
........3-10
CENTER BEARING - INSTALLATION
.......3-10
CENTER BEARING - OPERATION
..........3-10
CENTER BEARING - REMOVAL
...........3-10
CENTER BEARING ADJUSTMENT,
CENTER BEARING
.....................3-10
CENTER CONSOLE - INSTALLATION
.....23-122
CENTER CONSOLE - REMOVAL
.........23-122
CENTER CONSOLE LID - INSTALLATION
. . 23-132
CENTER CONSOLE LID - REMOVAL
.....23-131
6 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

CENTER HIGH MOUNTED STOP LAMP -
INSTALLATION........................8L-6
CENTER HIGH MOUNTED STOP LAMP -
REMOVAL...........................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION..................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL.....................8L-6
CENTER SEAT ARMREST/CONSOLE -
INSTALLATION......................23-132
CENTER SEAT ARMREST/CONSOLE -
REMOVAL.........................23-132
CENTER SEAT ARMREST/LATCH COVER -
INSTALLATION......................23-132
CENTER SEAT ARMREST/LATCH COVER -
REMOVAL.........................23-132
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-11
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING........................8E-4
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY..................Intro.-12
CHAIN COVER(S) - INSTALLATION,
TIMING BELT..........9-113,9-169,9-226,9-56
CHAIN COVER(S) - REMOVAL, TIMING
BELT ................9-113,9-169,9-225,9-56
CHAIN STRETCH - INSPECTION,
MEASURING TIMING....9-114,9-170,9-227,9-58
CHANNEL - INSTALLATION, GLASS RUN . . 23-70
CHANNEL - REMOVAL, GLASS RUN......23-70
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-46
CHARGE AIR COOLER AND PLUMBING -
CLEANING..........................11-18
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION.......................11-17
CHARGE AIR COOLER AND PLUMBING -
INSPECTION........................11-18
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION.......................11-18
CHARGE AIR COOLER AND PLUMBING -
OPERATION.........................11-17
CHARGE AIR COOLER AND PLUMBING -
REMOVAL..........................11-17
CHARGING - DESCRIPTION.............8F-27
CHARGING - OPERATION..............8F-27
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-9
CHARGING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-27
CHART, SPECIFICATIONS - TORQUE........5-3
CHART, SPECIFICATIONS -
TORQUE.............19-19,19-39,19-41,19-9
CHART, SPECIFICATIONS -
TORQUE.....................2-15,2-27,2-8
CHART, SPECIFICATIONS - TORQUE......22-11
CHARTS - DIAGNOSIS AND TESTING,
DIAGNOSIS......21-149,21-320,21-492,21-663
CHARTS - DIAGNOSIS AND TESTING,
SMOKE DIAGNOSIS...................9-234
CHASSIS ADAPTER BRACKET -
INSTALLATION, CAB...................13-9
CHASSIS ADAPTER BRACKET -
REMOVAL, CAB.......................13-9
CHECK - INSTALLATION...............23-78
CHECK - REMOVAL...................23-78
CHECK - STANDARD PROCEDURE,
COOLANT LEVEL......................7-16
CHECK - STANDARD PROCEDURE, FLUID
LEVEL..........21-199,21-370,21-545,21-715
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME . . . 21-209,21-379,21-554,21-724
CHECK CABLE - INSTALLATION.........23-63
CHECK CABLE - REMOVAL.............23-62
CHECK GAUGES INDICATOR -
DESCRIPTION.......................8J-17
CHECK GAUGES INDICATOR -
OPERATION.........................8J-17
CHECK OUT - STANDARD PROCEDURE,
OWNER............................30-22
CHECK VALVE - DESCRIPTION, ONE WAY . 25-30
CHECK VALVE - DESCRIPTION, VACUUM
. . 24-28
CHECK VALVE - DIAGNOSIS AND
TESTING, ONE-WAY
..................25-30
CHECK VALVE - INSTALLATION, ONE
WAY
...............................25-30
CHECK VALVE - INSTALLATION, VACUUM
. 24-29
CHECK VALVE - OPERATION, ONE WAY
. . . 25-30CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, ONE WAY....25-30
CHECK VALVE - REMOVAL, VACUUM.....24-29
CHECKING BATTERY ELECTROLYTE
LEVEL - STANDARD PROCEDURE.........8F-8
CHECKING TRANSMISSION CLUTCH AND
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR................21-147,21-318
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-4
CHILD TETHER - INSTALLATION..........8O-9
CHILD TETHER - REMOVAL.............8O-9
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-2
CHIME WARNING SYSTEM - OPERATION . . . 8B-1
CHOKE RELAY - DESCRIPTION, RADIO....8A-8
CHOKE RELAY - DIAGNOSIS AND
TESTING, RADIO......................8A-8
CHOKE RELAY - INSTALLATION, RADIO....8A-9
CHOKE RELAY - OPERATION, RADIO......8A-8
CHOKE RELAY - REMOVAL, RADIO.......8A-9
CIGAR LIGHTER - DIAGNOSIS &
TESTING.........................8W-97-2
CIGAR LIGHTER OUTLET - DESCRIPTION . 8W-97-2
CIGAR LIGHTER OUTLET -
INSTALLATION....................8W-97-3
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL....8W-97-3
CIRCUIT ACTUATION TEST MODE -
DESCRIPTION........................25-1
CIRCUIT BREAKER - DESCRIPTION....8W-97-4
CIRCUIT BREAKER - DIAGNOSIS &
TESTING.........................8W-97-4
CIRCUIT SENSE - DESCRIPTION,
IGNITION...........................8E-17
CIRCUIT SENSE - OPERATION, IGNITION . . 8E-19
CIRCUITS - DIESEL - OPERATION,
NON-MONITORED....................25-23
CIRCUITS - GAS ENGINES - OPERATION,
NON-MONITORED....................25-22
CLAMPS - DESCRIPTION, HOSE...........7-2
CLAMPS - OPERATION, HOSE.............7-2
CLASSIFICATION OF LUBRICANTS -
STANDARD PROCEDURE.................0-3
CLEANER ELEMENT - INSTALLATION,
AIR ...............................9-245
CLEANER ELEMENT - REMOVAL, AIR.....9-244
CLEANING AND INSPECTION, OIL
COOLER & LINES....................9-296
CLEANING, APPEARANCE TIPS..........30-21
CLEANING/REVERSE FLUSHING -
STANDARD PROCEDURE, COOLING
SYSTEM............................7-16
CLEARANCE - STANDARD PROCEDURE,
CONNECTING ROD BEARING AND
CRANKSHAFT JOURNAL...............9-274
CLEARANCE - STANDARD PROCEDURE,
MAIN BEARING......................9-275
CLEARANCE LAMP - INSTALLATION.......8L-6
CLEARANCE LAMP - REMOVAL..........8L-6
CLOCKSPRING - DESCRIPTION.........8O-10
CLOCKSPRING - INSTALLATION.........8O-13
CLOCKSPRING - OPERATION...........8O-10
CLOCKSPRING - REMOVAL............8O-11
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-11
CLOSURE PANEL TRIM - INSTALLATION,
REAR.............................23-121
CLOSURE PANEL TRIM - REMOVAL,
REAR.............................23-120
CLUB/QUAD CAB - INSTALLATION.......8O-20
CLUB/QUAD CAB - REMOVAL...........8O-19
CLUSTER - ASSEMBLY, INSTRUMENT....8J-13
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-6
CLUSTER - DISASSEMBLY, INSTRUMENT . . 8J-11
CLUSTER - INSTALLATION, INSTRUMENT . 8J-14
CLUSTER - OPERATION, INSTRUMENT.....8J-3
CLUSTER - REMOVAL, INSTRUMENT
.....8J-10
CLUSTER BEZEL - INSTALLATION
.......23-110
CLUSTER BEZEL - REMOVAL
..........23-109
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
DESCRIPTION, FAN DRIVE VISCOUS
......7-56
CLUTCH - 3.9L/5.2L/5.9L/8.0L -
OPERATION, FAN DRIVE VISCOUS
........7-56CLUTCH - 5.9L DIESEL - DESCRIPTION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - 5.9L DIESEL - OPERATION,
FAN DRIVE VISCOUS...................7-57
CLUTCH - ASSEMBLY, FRONT . . . 21-206,21-376,
21-550,21-721
CLUTCH - ASSEMBLY, REAR....21-248,21-419,
21-593,21-766
CLUTCH - CLEANING, REAR....21-247,21-418,
21-593,21-765
CLUTCH - DESCRIPTION.................6-1
CLUTCH - DESCRIPTION, A/C
COMPRESSOR.......................24-13
CLUTCH - DESCRIPTION, FRONT . 21-202,21-373,
21-548,21-718
CLUTCH - DESCRIPTION, OVERDRIVE . . . 21-214,
21-385,21-560,21-731
CLUTCH - DESCRIPTION, REAR . . 21-246,21-417,
21-591,21-764
CLUTCH - DIAGNOSTIC AND TESTING......6-2
CLUTCH - DISASSEMBLY, FRONT......21-202,
21-373,21-549,21-719
CLUTCH - DISASSEMBLY, REAR . 21-247,21-418,
21-592,21-765
CLUTCH - INSPECTION, A/C
COMPRESSOR.......................24-16
CLUTCH - INSPECTION, FRONT . . 21-205,21-376,
21-550,21-721
CLUTCH - INSPECTION, REAR . . . 21-248,21-419,
21-593,21-765
CLUTCH - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH - OPERATION....................6-1
CLUTCH - OPERATION, A/C
COMPRESSOR.......................24-13
CLUTCH - OPERATION, FRONT . . 21-202,21-373,
21-548,21-718
CLUTCH - OPERATION, OVERDRIVE....21-214,
21-385,21-560,21-731
CLUTCH - OPERATION, REAR . . . 21-246,21-417,
21-592,21-764
CLUTCH - REMOVAL, A/C COMPRESSOR . . 24-14
CLUTCH - SPECIFICATIONS...............6-7
CLUTCH - WARNING....................6-2
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING TRANSMISSION......21-147,21-318
CLUTCH AND BAND OPERATION -
DIAGNOSIS AND TESTING, AIR
TESTING TRANSMISSION.......21-490,21-661
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-13
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - ASSEMBLY,
OVERRUNNING . . . 21-236,21-406,21-581,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - CLEANING, OVERRUNNING . 21-236,
21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DESCRIPTION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - DISASSEMBLY,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - INSPECTION,
OVERRUNNING . . . 21-236,21-406,21-580,21-752
CLUTCH CAM/OVERDRIVE PISTON
RETAINER - OPERATION,
OVERRUNNING . . . 21-235,21-405,21-580,21-751
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-13
CLUTCH DISC - DESCRIPTION............6-7
CLUTCH DISC - INSTALLATION............6-9
CLUTCH DISC - OPERATION..............6-8
CLUTCH DISC - REMOVAL...............6-8
CLUTCH HOUSING - DIAGNOSIS AND
TESTING............................6-11
CLUTCH HOUSING - INSTALLATION.......6-13
CLUTCH HOUSING - REMOVAL...........6-13
CLUTCH PEDAL - INSTALLATION
.........6-19
CLUTCH PEDAL - REMOVAL
.............6-18
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION
........................6-22
CLUTCH PEDAL POSITION SWITCH -
OPERATION
..........................6-22
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR
.......................24-17
BR/BEINDEX 7
Description Group-Page Description Group-Page Description Group-Page

CONTROL/CENTRAL TIMER MODULE -
INSTALLATION, BODY..................8E-6
CONTROL/CENTRAL TIMER MODULE -
OPERATION, BODY....................8E-3
CONTROL/CENTRAL TIMER MODULE -
REMOVAL, BODY......................8E-5
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION.......................8E-11
CONTROLLER ANTILOCK BRAKE -
INSTALLATION.......................8E-12
CONTROLLER ANTILOCK BRAKE -
OPERATION.........................8E-11
CONTROLLER ANTILOCK BRAKE -
REMOVAL..........................8E-12
CONTROLS - DIAGNOSIS AND TESTING,
OVERDRIVE
ELECTRICAL.....21-215,21-386,21-579,21-732
CONVERTER - 3.9L/5.2L/5.9L -
DESCRIPTION, CATALYTIC...............11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSPECTION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
INSTALLATION, CATALYTIC..............11-5
CONVERTER - 3.9L/5.2L/5.9L -
OPERATION, CATALYTIC................11-5
CONVERTER - 3.9L/5.2L/5.9L -
REMOVAL, CATALYTIC..................11-5
CONVERTER - 5.9L HEAVY DUTY/8.0L -
DESCRIPTION, CATALYTIC...............11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSPECTION, CATALYTIC................11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
INSTALLATION, CATALYTIC..............11-7
CONVERTER - 5.9L HEAVY DUTY/8.0L -
OPERATION, CATALYTIC................11-6
CONVERTER - 5.9L HEAVY DUTY/8.0L -
REMOVAL, CATALYTIC..................11-6
CONVERTER - DESCRIPTION,
TORQUE........21-256,21-427,21-600,21-773
CONVERTER - INSTALLATION,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER - OPERATION,
TORQUE........21-260,21-430,21-604,21-777
CONVERTER - REMOVAL,
TORQUE........21-261,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
DESCRIPTION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
OPERATION,
TORQUE........21-262,21-432,21-605,21-778
CONVERTER DRAINBACK VALVE -
STANDARD PROCEDURE,
TORQUE........21-262,21-432,21-606,21-778
CONVERTER HOUSING FLUID LEAK -
DIAGNOSIS AND
TESTING........21-148,21-319,21-491,21-662
COOLANT - DESCRIPTION...............7-40
COOLANT - OPERATION
................7-40
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
..................7-16
COOLANT FLOW - DIAGNOSIS AND
TESTING, RADIATOR
...........7-59,7-61,7-63
COOLANT LEVEL CHECK - STANDARD
PROCEDURE
.........................7-16
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
DESCRIPTION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
INSTALLATION
........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
OPERATION
..........................7-41
COOLANT RECOVERY CONTAINER -
3.9L/5.2L/5.9L/5.9L DIESEL -
REMOVAL
...........................7-41
COOLANT RECOVERY CONTAINER - 8.0L
- DESCRIPTION
.......................7-42
COOLANT RECOVERY CONTAINER - 8.0L
- OPERATION
.........................7-42
COOLANT SELECTION-ADDITIVES -
STANDARD PROCEDURE
................7-17
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE
............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE
...........7-48COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-48
COOLANT TEMP SENSOR - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-48
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - DESCRIPTION, ENGINE............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - INSTALLATION, ENGINE...........7-50
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - OPERATION, ENGINE.............7-49
COOLANT THERMOSTAT - 3.9L/5.2L/
5.9L - REMOVAL, ENGINE...............7-49
COOLANT THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE................7-55
COOLANT THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE...................7-54
COOLANT THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE....................7-55
COOLANT THERMOSTAT - 8.0L -
DESCRIPTION, ENGINE.................7-52
COOLANT THERMOSTAT - 8.0L -
INSTALLATION, ENGINE................7-53
COOLANT THERMOSTAT - 8.0L -
OPERATION, ENGINE...................7-52
COOLANT THERMOSTAT - 8.0L -
REMOVAL, ENGINE....................7-52
COOLER - 3.9L/5.2L/5.9L - ASSEMBLY,
TRANS..............................7-82
COOLER - 3.9L/5.2L/5.9L -
DESCRIPTION, TRANS.................7-79
COOLER - 3.9L/5.2L/5.9L -
DISASSEMBLY, TRANS...................7-81
COOLER - 3.9L/5.2L/5.9L -
INSTALLATION, TRANS.................7-82
COOLER - 3.9L/5.2L/5.9L - OPERATION,
TRANS..............................7-79
COOLER - 3.9L/5.2L/5.9L - REMOVAL,
TRANS..............................7-81
COOLER - 5.9L DIESEL - DESCRIPTION,
TRANS..............................7-85
COOLER - 5.9L DIESEL - INSTALLATION,
TRANS..............................7-88
COOLER - 5.9L DIESEL - OPERATION,
TRANS..............................7-85
COOLER - 8.0L - DESCRIPTION, TRANS....7-82
COOLER - 8.0L - INSTALLATION, TRANS . . . 7-85
COOLER - 8.0L - OPERATION, TRANS.....7-82
COOLER - 8.0L - REMOVAL, TRANS.......7-84
COOLER - INSTALLATION, AIR TO OIL.....7-88
COOLER & LINES - CLEANING AND
INSPECTION, OIL.....................9-296
COOLER - REMOVAL, AIR TO OIL.........7-87
COOLER - REMOVAL, WATER TO OIL......7-87
COOLER - STANDARD PROCEDURE,
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL...........7-80,7-83,7-86
COOLER - STANDARD PROCEDURE,
FLUSHING COOLERS AND TUBES -
WITH RADIATOR IN-TANK
TRANSMISSION OIL...........7-79,7-83,7-85
COOLER AND PLUMBING - CLEANING,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
DESCRIPTION, CHARGE AIR............11-17
COOLER AND PLUMBING - INSPECTION,
CHARGE AIR........................11-18
COOLER AND PLUMBING -
INSTALLATION, CHARGE AIR...........11-18
COOLER AND PLUMBING - OPERATION,
CHARGE AIR........................11-17
COOLER AND PLUMBING - REMOVAL,
CHARGE AIR........................11-17
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-80,7-83,7-86
COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE, FLUSHING
........7-79,7-83,7-85
COOLING, SPECIAL TOOLS
..............7-18
COOLING SYSTEM - OPERATION
..........7-4
COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
DRAINING
...........................7-15COOLING SYSTEM 3.9L/5.2L/5.9L/8.0L
ENGINES - STANDARD PROCEDURE,
REFILLING...........................7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, DRAINING.....7-15
COOLING SYSTEM 5.9L DIESEL ENGINE
- STANDARD PROCEDURE, REFILLING.....7-15
COOLING SYSTEM CLEANING/REVERSE
FLUSHING - STANDARD PROCEDURE.....7-16
COOLING SYSTEM DIESEL ENGINE -
DIAGNOSIS AND TESTING..............7-12
COOLING SYSTEM FLOW - 3.9L/5.2L/
5.9L ENGINE - DESCRIPTION.............7-1
COOLING SYSTEM FLOW - 5.9L DIESEL
- DESCRIPTION........................7-1
COOLING SYSTEM GAS ENGINE -
DIAGNOSIS AND TESTING...............7-7
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-5
COOLING SYSTEM REQUIREMENTS -
DESCRIPTION........................24-1
CORE - DESCRIPTION, HEATER.........24-55
CORE - INSTALLATION, HEATER.........24-56
CORE - OPERATION, HEATER...........24-55
CORE - REMOVAL, HEATER............24-56
CORE GROUND STRAP - INSTALLATION,
HEATER............................8A-15
CORE GROUND STRAP - REMOVAL,
HEATER............................8A-14
CORNER SEAL - INSTALLATION, FRONT
DOOR UPPER......................23-154
CORNER SEAL - REMOVAL, FRONT
DOOR UPPER........................23-154
COUPLERS - DESCRIPTION, A/C LINE....24-40
COUPLERS - OPERATION, A/C LINE......24-41
COUPLERS - STANDARD PROCEDURE,
A/C LINE...........................24-43
COVER - INSTALLATION, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - INSTALLATION, COWL TRIM . . . 23-120
COVER - INSTALLATION, GEAR HOUSING . 9-307
COVER - INSTALLATION, INSTRUMENT
PANEL TOP........................23-115
COVER - INSTALLATION, SEAT BACK....23-137
COVER - INSTALLATION, SEAT CUSHION . 23-139
COVER - INSTALLATION, SHIFT . . . 21-133,21-90
COVER - INSTALLATION, STANCHION....23-143
COVER - INSTALLATION, STEERING
COLUMN OPENING..................23-116
COVER - REMOVAL, CENTER SEAT
ARMREST/LATCH...................23-132
COVER - REMOVAL, COWL TRIM.......23-119
COVER - REMOVAL, GEAR HOUSING.....9-306
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-114
COVER - REMOVAL, SEAT BACK........23-137
COVER - REMOVAL, SEAT CUSHION.....23-139
COVER - REMOVAL, SHIFT.......21-132,21-90
COVER - REMOVAL, STANCHION.......23-143
COVER - REMOVAL, STEERING COLUMN
OPENING..........................23-115
COVER - REMOVAL, WHEEL............22-12
COVER - SPLIT BENCH - INSTALLATION,
SEAT BACK........................23-138
COVER - SPLIT BENCH - INSTALLATION,
SEAT CUSHION.....................23-140
COVER - SPLIT BENCH - REMOVAL,
SEAT BACK........................23-137
COVER - SPLIT BENCH - REMOVAL,
SEAT CUSHION.....................23-139
COVER GASKET - DESCRIPTION,
CYLINDER...........................9-79
COVER GASKET - DESCRIPTION,
CYLINDER HEAD......................9-22
COVER GASKET - OPERATION,
CYLINDER HEAD......................9-22
COVER INSTALLED - INSTALLATION,
FRONT OIL SEAL - FRONT.............9-205
COVER INSTALLED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER REMOVED - INSTALLATION,
FRONT OIL SEAL - FRONT
.............9-205
COVER REMOVED - REMOVAL, FRONT
OIL SEAL - FRONT
...................9-204
COVER(S) - CLEANING, CYLINDER HEAD
. 9-138,
9-194,9-24,9-253,9-81
COVER(S) - DESCRIPTION, CYLINDER
HEAD
..............................9-194
BR/BEINDEX 9
Description Group-Page Description Group-Page Description Group-Page