2000 YAMAHA XV125S wheel torque

6-25
1
2
3
4
5
6
7
8
9To tighten the chain, turn the
chain adjusting nuts in direc-
tion a. To loosen the chain,
turn the chain adjusting nuts in
direction band push the
wheel forward. Turn each
chain adjusting nut exactly the
same amount to maintain cor-
rect axle alignment. There are
marks on each side of the
swingarm. Use these marks to
align the rear wheel.
EC000096
cC
Too little chain slack will overload
the engine and other vital parts.
Keep the slack within the specified
limits.
5. After adjusting, be sure to
tighten each chain adjusting
locknut. Then tighten the axle
nut to the specified torque.
Tightening torque:
Axle nut:
105 Nm (10.5 m·kg)
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU00750Drive chain slack adjustment
1. Loosen the rear brake pedal
free play adjusting nut.
1. Rear brake pedal free play adjusting nut
2. Remove the cotter pin from
the axle nut.
3. Loosen the axle nut.
4. Loosen the chain adjusting
locknuts on each side of the
swingarm.
1. Cotter pin
2. Alignment marks
3. Locknut
4. Chain adjusting nut
5. Axle nut
1
1
2
5
b
a
43
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 56

1
2
3
4
5
6
7
8
9
6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
5. Push down hard on the han-
dlebars several times to check
for proper fork operation.
6. Tightening the wheel axle to
the specified torque.
7. Install the pinch bolts and
tighten them to the specified
torque.
8. Install the speedometer cable.EAU01550Rear wheel removalEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Remove the axle nut cotter pin
and brake torque rod cotter
pin. Tightening torque:
Wheel axle:
59 Nm (5.9 m·kg)
Pinch bolt:
20 Nm (2.0 m·kg)
1
3 4
2
5
2. Loosen the axle nut and brake
torque nut.
3. Elevate the rear wheel by plac-
ing a suitable stand under the
engine.
4. Remove the brake torque rod
nut and bolt from the brake
shoe plate.
1. Brake torque rod
2. Brake torque rod cotter pin
3. Brake torque rod nut
4. Brake rod
5. Rear brake pedal free play adjusting nut
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 69

6-39
1
2
3
4
5
6
7
8
97. Adjust the rear brake pedal
height and free play. (See page
6-21.)
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU01696Rear wheel installation
1. Install the rear wheel and the
axle.
2. Install the axle nut and let the
motorcycle down.
3. Insert the brake rod into the
brake cam lever and install the
brake pedal free play adjusting
nut.
4. Install the brake torque rod
bolt and tighten to the speci-
fied tightening torque. Then
install a new cotter pin.
5. Adjust the drive chain free
play. (See page 6-25.)
6. Tighten the axle nut to the
specified tightening torque. Specified torque:
Brake torque rod bolt:
23 Nm (2.3 m·kg)
Specified torque:
Axle nut:
105 Nm (10.5 m·kg)
435
12
5. Remove the rear brake pedal
free play adjusting nut and
brake rod from the brake cam
lever.
6. Loosen the locknuts and chain
adjusting nuts on each side.
7. Remove the axle nut.
8. Pull out the wheel axle and
remove the wheel assembly.
1. Cotter pin
2. Alignment marks
3. Locknut
4. Chain adjusting nut
5. Axle nut
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 70