EAU00009
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9 GIVE SAFETY THE RIGHT OF WAY ..................1-1
DESCRIPTION .....................................................2-1
Left view............................................................2-1
Right view .........................................................2-2
Controls/Instruments .......................................2-3
INSTRUMENT AND CONTROL
FUNCTIONS ........................................................3-1
Main switch ......................................................3-1
Indicator lights..................................................3-1
Speedometer ....................................................3-2
Handlebar switches..........................................3-2
Clutch lever .......................................................3-4
Shift pedal.........................................................3-4
Front brake lever ..............................................3-4
Rear brake pedal ..............................................3-5
Fuel tank cap.....................................................3-5
Fuel ....................................................................3-6
Fuel cock ...........................................................3-7
Starter (choke) “1” .........................................3-8
Steering lock .....................................................3-8
Seat ...................................................................3-9
Helmet holder ...................................................3-9
Rear shock absorber adjustment ..................3-10
Sidestand ........................................................3-10Sidestand/clutch switch operation check .....3-11
PRE-OPERATION CHECKS.................................4-1
Pre-operation check list ...................................4-1
OPERATION AND IMPORTANT RIDING
POINTS................................................................5-1
Starting the engine ..........................................5-1
Starting a warm engine ...................................5-3
Shifting..............................................................5-4
Recommended shift point
(for Switzerland only) ......................................5-4
Tips for reducing fuel consumption ...............5-5
Engine break-in ................................................5-5
Parking ..............................................................5-6
PERIODIC MAINTENANCE AND MINOR
REPAIR ................................................................6-1
Tool kit ..............................................................6-1
Periodic maintenance and lubrication............6-3
Panel removal and installation .......................6-6
Panel A ..............................................................6-6
Panel B ..............................................................6-7
Spark plugs .......................................................6-8
Engine oil ..........................................................6-9
Air filter ...........................................................6-12
1
2
3
4
5
6
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 5
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
3-9
EAU03020Seat
To remove
1. Remove panels A and B. (See
page 6-6 for panel removal
and installation procedures.)
2. Remove the rider seat bolts
and lift the seat upward.
1. Bolt (´2)
To install
1. Insert the projection on the
front of the rider seat into the
seat holder, then tighten the
seat bolts.
2. Install the panels.
NOTE:
Make sure that the seat is securely
fitted.
1. Projection
2. Seat holder
EAU00260Helmet holder
To open the helmet holder, insert
the key in the lock and turn it as
shown. To lock the helmet holder,
replace the holder in its original
position.
EW000030
w
Never ride with a helmet in the
helmet holder. The helmet may hit
objects, causing loss of control
and possibly an accident.
1. Helmet holder
2. Open
1
1
22 1
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 21
1
2
3
4
5
6
7
8
9
MOTORCYCLE CARE AND STORAGE
7-2
8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel bearings, swingarm
bearings, forks and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure they
do not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.After riding in the rain, near the
sea or on salt-sprayed roads
Since sea salt or salt sprayed on
the roads in the winter are
extremely corrosive in combina-
tion with water, carry out the fol-
lowing steps after each ride in the
rain, near the sea or on salt-
sprayed roads. (Salt sprayed in the
winter may remain on the roads
well into spring.)
1. Clean your motorcycle with
cold water and soap after the
engine has cooled down.
ECA00012
cC
Do not use warm water since it
increases the corrosive action of
the salt.
2. Be sure to apply a corrosion
protection spray on all (even
chrome- and nickel-plated)
metal surfaces to prevent cor-
rosion.
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 74
