2000 TOYOTA CAMRY thermostat

CAMRY
CAMRY ± OUTLINE OF NEW FEATURES 26
OUTLINE OF NEW FEATURES
The CAMRY is a high-quality family sedan with advanced technology and sporty performance. The following
changes are made for the 2000 model year.
1. Model Line-Up
The 5S-FNE CNG (Compressed Natural Gas) engine model has been added.
2. Exterior
Four new exterior colors have been added, for a total of 10 colors.
The design of the front and rear bumpers has been changed.
The bumper and the radiator grille have been made separate, and the radiator grille is chrome-plated.
The side protection molding has been increased in size. On the XLE grade model, chrome stripes have been
adopted for the side protection molding.
The 4-light multi-reflector type headlights are adopted with new styling.
The design and styling of the rear combination light has been changed.
The 16º aluminum alloy wheel and wheel cap has been added.
The styling of the 15º full wheel cover has been changed.
3. Interior
Wood-grain panels have been adopted in the interior of the XLE grade model.
CRS tether anchor brackets have been provided on the package tray trim. (except 5S-FNE engine Model)
A clock with an outside temperature gauge has been provided on the models with manual air conditioning.
4. 5S-FE Engine
The intake system from the inlet duct to the throttle body has been improved to increase torque and reduce
noise.
The direction of the rotation of the radiator cooling fan has been reversed.
A 2-way exhaust control system has been adopted on the TMMK made model.
Along with the discontinuance of the air assist system, the fuel injectors and the IAC valve have been
changed for the California specification model, in order to meet ULEV (Ultra-Low Emission Vehicle) re-
quirement.
The system for detecting evaporative emission leaks has been changed. For details, see the General 2000
Features section.
5. 5S-FNE Engine
Based on the 5S-FE gasoline engine, the 5S-FNE engine uses compressed natural gas. The fuel lines have
been designed exclusively for compressed natural gas application.
6. 1MZ-FE Engine
The system for detecting evaporative emission leaks has been changed. For details, see the General 2000
Features section.
A diagnostic trouble code (DTC) has been added for indicating a thermostat malfunction.
7. Automatic Transaxle
The overdrive switch has been changed to the momentary type. For details, see the General 2000 Features
section.
The differential gear ratio of the A140E automatic transaxle has been changed for the 5S-FNE engine mod-
el to accommodate the performance of the 5S-FNE engine.

CAMRY ± NEW FEATURES54
1MZ-FE ENGINE
The following items have been changed in the '00 CAMRY.
The system for detecting evaporative emission leaks has been changed.
For details, see the General 2000 Features section.
A thermostat monitor function has been newly provided. This function monitors the changes in the coolant
temperature at the time the engine is started, and if the coolant temperature does not reach a specified value
within a prescribed length of time, the thermostat is determined to be faulty.
AUTOMATIC TRANSAXLE
As in the 5S-FE engine model, the A140E automatic transaxle is used on the 5S-FNE engine model.
The gear ratio of the differential has been lowered to accommodate the performance of the 5S-FNE engine
and to ensure fuel economy.

Specifications 
Item
5S-FNE Engine5S-FE Engine
1st2.810
2nd1.549
Gear Ratio3rd1.000
4th (Overdrive)0.706
Reverse2.296
Counter Gear Ratio0.945
Differential Gear Ratio4.1763.944
Fluid Capacity
Liters
Transmission5.6 (5.9, 4.9)
Liters
(US qts, Imp. qts)
Differential1.6 (1.7, 1.4)
Fluid TypeATF D-II or
DEXRON)III (DEXRON)II)

The cooling system is composed of the water jacket (inside the cylinder block and cylinder head),
radiator, water pump, thermostat, electric fan, hoses and other components.
Engine coolant which is heated in the water jacket is pumped to the radiator, through which an
electric fan blows air to cool the coolant as it passes through. Engine coolant which has been
cooled is then sent back to the engine by the water pump, where it cools the engine.
The water jacket is a network of channels in the shell of the cylinder block and cylinder head
through which coolant passes. It is designed to provide adequate cooling of the cylinders and
combustion chambers which become heated during engine operation.
DESCRIPTION
This engine utilizes a pressurized forced circulation cooling system which includes a thermostat
equipped with a bypass valve mounted on the inlet side.
OPERATIONCOOLING SYSTEM
± 5S±FE ENGINECOOLING SYSTEMEG1±238

RADIATOR
The radiator performs the function of cooling the coolant which has passed through the water
jacket and become hot, and it is mounted in the front of the vehicle. The radiator consists of an
upper tank and lower tank, and a core which connects the two tanks. The upper tank contains the
inlet for coolant from the water jacket and the filler inlet. It also has a hose attached through
which excess coolant or steam can flow. The lower tank has an outlet and drain cock for the
coolant. The core contains many tubes through which coolant flows from the upper tank to the
lower tank as well as to cooling fins which radiate heat away from the coolant in the tubes. The
air sucked through the radiator by the electric fan, as well as the wind generated by the vehicle's
travel, passes through the radiator, cooling the coolant. Models with automatic transmission
include an automatic transmission fluid cooler built into the lower tank of the radiator. A fan with
an electric motor is mounted behind the radiator to assist the flow of air through the radiator. The
fan operates when the engine coolant temperature becomes high in order to prevent it from be-
coming too high.
RADIATOR CAP
The radiator cap is a pressure type cap which seals the radiator, resulting in pressurization of the
radiator as the coolant expands. The pressurization prevents the coolant from boiling even when
the engine coolant temperature exceeds 100°C (212°F). A relief valve (pressurization valve) and a
vacuum valve (negative pressure valve) are built into the radiator cap. The relief valve opens and
lets steam escape through the overflow pipe when the pressure generated inside the cooling sys-
tem exceeds the limit (coolant temperature: 110±120°C (230±248°F), pressure; 58.8103.0 kpa
(0.6±1.05 kgf/cm
2, 8.5±14.9 psi). The vacuum valve opens to alleviate the vacuum which develops
in the cooling system after the engine is stopped and the engine coolant temperature drops. The
valve's opening allows the coolant in the reservoir tank to return to the cooling system.
RESERVOIR TANK
The reservoir tank is used to catch coolant which overflows from the cooling system as a result
of volumetric expansion when the coolant is heated. The coolant in the reservoir tank returns to
the radiator when the coolant temperature drops, thus keeping the radiator full at all times and
avoiding needless coolant loss.
Check the reservoir tank level to learn if the coolant needs to be replenished.
WATER PUMP
The water pump is used for forced circulation of coolant through the cooling system. It is
mounted on the front of the cylinder block and driven by a timing belt.
THERMOSTAT
The thermostat has a wax type bypass valve and is mounted in the water inlet housing. The
thermostat includes a type of automatic valve operated by fluctuations in the engine coolant
temperature. This valve closes when the engine coolant temperature drops, preventing the
circulation of coolant through the engine and thus permitting the engine to warm up rapidly. The
valve opens when the engine coolant temperature has risen, allowing the circulation of coolant.
Wax inside the thermostat expands when heated and contracts when cooled. Heating the wax
thus generates pressure which overpowers the force of the spring which keeps the valve closed,
thus opening the valve. When the wax cools, its contraction allows the force of the spring to take
effect once more, closing the valve. The thermostat in this engine operates at a temperature of
82
C (180
F).
± 5S±FE ENGINECOOLING SYSTEMEG1±239

(See Components for Removal and Installation)
1. INSTALL THERMOSTAT AND WATER INLET TO
WATER PUMP COVER
(a) Install a new gasket to the thermostat.
(b) Align the jiggle valve of the thermostat with the upper
side of the stud bolt, and insert the thermostat in the
water pump.
HINT: The jiggle valve may be set within 5
of either
side of the prescribed position. 10. REMOVE WATER INLET AND THERMOSTAT FROM
WATER PUMP COVER
(a) Remove the 2 nuts and water inlet from the water
pump.
(b) Remove the thermostat.
(c) Remove the gasket from the thermostat.
WATER PUMP INSPECTION
INSPECT WATER PUMP
Turn the pulley and check that the water pump bear±
ing moves smoothly and quietly.
(c) Install the water inlet with the 2 nuts.
Torque: 8.8 N±m (90 kgf±cm. 78 in.±lbf)
WATER PUMP INSTALLATION
± 5S±FE ENGINECOOLING SYSTEMEG1±244

THERMOSTAT REMOVAL
HINT: Removal of the thermostat would have an ad±
verse effect, causing a lowering of cooling efficiency.
Do not remove the thermostat, even if the engine
tends to overheat.
1. DRAIN ENGINE COOLANT (See page EG1±241)
2. REMOVE OIL FILTER
Using SST, remove the oil filter.
SST 09228±06500
3. REMOVE WATER INLET AND THERMOSTAT
(a) Remove the 2 nuts and water inlet from the water
pump.
(b) Remove the thermostat.
(c) Remove the gasket from the thermostat.
THERMOSTAT
COMPONENTS FOR REMOVAL AND
INSTALLATION
± 5S±FE ENGINECOOLING SYSTEMEG1±247

THERMOSTAT INSTALLATION
(See Components for Removal and Installation)
1. PLACE THERMOSTAT IN WATER PUMP
(a) Install a new gasket to the thermostat.
(b) Align the jiggle valve of the thermostat with the upper
side of the stud bolt, and insert the thermostat in the
water pump.
HINT: The jiggle valve may be set within 5
of either
side of the prescribed position.
2. INSTALL WATER INLET
Install the water inlet with the 2 nuts.
Torque: 8.8 N±m (90 kgf±cm, 78in.±Ibf)
(c) Check the valve lift.
Valve rift:
8 mm (0.31 in.) or more at 95
C (203
F)
If the valve lift is not as specified, replace the thermo±
stat.
(d) Check that the valve spring is tight when the thermo±
stat is fully closed.
If not closed, replace the thermostat. (a) Immerse the thermostat in water and gradually heat
the water.
(b) Check the valve opening temperature.
Valve opening temperature:
80 ± 84
C (176 ± 183
F)
If the valve opening temperature is not as specified,
replace the thermostat.
THERMOSTAT INSPECTION
INSPECT THERMOSTAT
HINT: The thermostat is numbered with the valve
opening temperature.
± 5S±FE ENGINECOOLING SYSTEMEG1±248

SERVICE SPECIFICATIONS
SERVICE DATA
TORQUE SPECIFICATIONS
Valve opening temperature
Valve lift
Water bypass pipe x Water pump cover
Radiator oil cooler x Radiator lower tank Water pump x Water pump cover
No.2 idler pulley x Cylinder block Water inlet x Water pump coverRelief valve opening pressure
Water pump x Cylinder blockCylinder block x Drain plug
Water inlet x Water pump
Radiator oil cooler pipe
Radiator support boltElectric
cooling fanRotating amperage
Part tightened Radiator cap
Plate height Thermostat
Radiator
± 5S±FE ENGINECOOLING SYSTEMEG1±267