2000 SUZUKI SWIFT Tightening Torque

GENERAL INFORMATION 0A-1
0ASECTION 0A
GENERAL INFORMATION
CONTENTS
HOW TO USE THIS MANUAL0A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Vehicles Equipped with a Supplemental Restraint (Air Bag) System 0A- 3. . . . . . . . . . . . . . . .
General Precautions0A- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Catalytic Converter 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Electrical Circuit Service 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Circuit Inspection Procedure 0A-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermittent and Poor Connection 0A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Installing Mobile Communication Equipment 0A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution in Servicing Full-Time 4WD Vehicle 0A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDENTIFICATION INFORMATION0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle Identification Number0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification Whether Vehicle Equipped with WU-TWC or Not 0A-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Identification Number0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Identification Number 0A-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING, CAUTION AND INFORMATION LABELS0A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE LIFTING POINTS0A-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL0A-22 . . . . . . . . . . . . . . . . . . . . . . . . . . .
FASTENER INFORMATION0A-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Fasteners0A-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fasteners Strength Identification 0A-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Tightening Torque0A-26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. Flywheel bolts or drive plate bolts for A / T vehicle
6) Install oil pump. Refer to “Oil pump”.
7) Install flywheel (for M / T vehicle) or drive plate
(for A / T vehicle).
Using special tool, lock flywheel or drive plate, and
tighten flywheel or drive plate bolts to specified
torque.
Special Tool
(A): 09924-17810
Tightening Torque
(c): 78 N
.m (7.8 kg-m, 56.0 lb-ft)
0A-2 GENERAL INFORMATION
HOW TO USE THIS MANUAL
1) There is a TABLE OF CONTENTS FOR THE WHOLE MANUAL
on the third page of this manual, whereby you can easily find the
section that offers the information you need. Also, there is a
CONTENTS on the first page of EACH SECTION, where the
main items in that section are listed.
2) Each section of this manual has its own pagination. It is indicated
at the top of each page along with the Section name.
3) The SPECIAL TOOL usage and TIGHTENING TORQUE
SPECIFICATION are given as shown in figure below.
4) A number of abbreviations are used in the text.
For their full explanations, refer to “ABBREVIATIONS AND
SYMBOLS MAY BE USED IN THIS MANUAL” of this section.
5) The SI, metric and foot-pound systems are used as units in this
manual.
6) DIAGNOSIS are included in each section as necessary.
7) At the end of each section, there are descriptions of SPECIAL
TOOLS, REQUIRED SERVICE MATERIALS and TIGHT-
ENING TORQUE SPECIFICATIONS that should be used for the
servicing work described in that section.

1. Transfer lock bolt
2. Shift fork shaft Testing following items

Speedometer

Chassis dynamo

Brake

Wheel balance (on car type)Towing vehicle with
front or rear
wheels lifted upDriving front
wheels which are
jacked up
4WD
2WD
GENERAL INFORMATION 0A-17
PRECAUTION IN SERVICING FULL-TIME 4WD VEHICLE
When performing any of the following types of work, be sure to make the vehicle as front wheel drive by cutting
transmission of driving force to the rear wheels. Otherwise, rear wheels are driven and vehicle accidents, damage
and personal injury may result.
SWITCHING FROM 4WD TO 2WD
Set 4WD / 2WD select lever located at lower side of transfer driven
case to 2WD as follows.
1) Loosen transfer lock bolt.
2) Push in shift fork shaft fully.
3) With shift fork shaft pushed in, tighten transfer lock bolt.
Tightening Torque
(a): 19 N
.m (1.9 kg-m, 14.0 lb-ft)
NOTE:

If shift fork shaft is hard to move, try to move it while turning
it to the right and left little by little. Do the same when setting
back to 4WD after servicing vehicle.

Upon completion of servicing, always set shift fork shaft
back to 4WD.

G (Base Color)
G (Base Color)
Y (Stripe Color)
0A-24 GENERAL INFORMATION
SYMBOLS
SYMBOLDEFINITIONSYMBOLDEFINITION
Tightening torqueApply SUZUKI BOND NO. 1216
99000-31160
Apply oil (Engine, transmission,
transfer, differential)Apply SILICONE SEALANT
99000-31120
Apply fluid (Brake, power steering or
automatic transmission fluid)Apply SEALING COMPOUND 366E
99000-31090
Apply SUZUKI SUPER GREASE A
99000-25010
Apply SUZUKI SUPER GREASE C
99000-25030Apply THREAD LOCK 1322
99000-32110
Apply SUZUKI SUPER GREASE E
99000-25050Apply THREAD LOCK 1333B
99000-32020
Apply SUZUKI SUPER GREASE H
99000-25120Apply THREAD LOCK 1342
99000-32050
Apply SUZUKI SUPER GREASE I
99000-25210
Apply SUZUKI BOND NO. 1215
99000-31110Do not reuse
Apply SUZUKI BOND NO. 1207C
99000-31150Note on reassembly
WIRE COLOR SYMBOLS
SymbolWire ColorSymbolWire Color
BBLKBlackO, OrORNOrange
BlBLUBlueRREDRed
BrBRNBrownWWHTWhite
GGRNGreenYYELYellow
GrGRYGrayPPNKPink
LblLT BLULight blueVPPLViolet
LgLT GRNLight green
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. “G”).
The dual-colored wire uses two color symbols (i.e. “G/Y”). The first
symbol represents the base color of the wire (“G” in the figure) and
the second symbol represents the color of the stripe (“Y” in the fig-
ure).

0A-26 GENERAL INFORMATION
Self-lock
nut
STANDARD TIGHTENING TORQUE
Each fastener should be tightened to the torque specified in each section of this manual. If no description or specifi-
cation is provided, refer to the following tightening torque chart for the applicable torque for each fastener. When
a fastener of greater strength than the original one is used, however, use the torque specified for the original fasten-
er.
NOTE:

For the flanged bolt, flanged nut and self-lock nut of 4T and 7T strength, add 10% to the tightening torque
given in the chart below.

The chart below is applicable only where the fastened parts are made of steel or light alloy.
Tightening torque chart
Thread Diameter (Nominal Diameter)
(mm)
45681012141618
Strength
A equivalent of 4T strength
fastenerN.m1.53.05.513294565105160
kg-m0.150.300.551.32.94.56.510.516
lb-ft1.02.54.09.521.032.547.076.0116.0
A equivalent of 6.8 strength
fastener without flangeN.m2.44.78.4204280125193280g
kg-m0.240.470.842.04.28.012.519.328
lb-ft2.03.56.014.530.558.090.5139.5202.5
A equivalent of 6.8 strength
fastener with flangeN.m2.44.98.8214484133203298g
kg-m0.240.490.882.14.48.413.320.329.8
lb-ft2.03.56.515.532.061.096.5147.0215.5
A equivalent of 7T strength
fastenerN.m2.34.510235085135210240
kg-m0.230.451.02.35.08.513.52124
lb-ft2.03.57.517.036.561.598.0152.0174.0
A equivalent of 8.8 strength
fastener without flangeN.m3.16.3112756105168258373g
kg-m0.310.631.12.75.610.516.825.837.3
lb-ft2.54.58.019.540.576.0121.5187.0270.0
A equivalent of 8.8 strength
fastener with flangeN.m3.26.512295911 3175270395g
kg-m0.320.651.22.95.911.317.52739.5
lb-ft2.55.09.021.043.082.0126.5195.5286.0

1. Thickness gauge IN
EX
0B-6 MAINTENANCE AND LUBRICATION
Water Pump Belt Replacement
Replace belt with a new one. Refer to SECTION 6B for replacement
procedure of pump belt.
NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.27 in.).
ITEM 1-2
Camshaft Timing Belt Replacement
Replace belt with new one. Refer to SECTION 6A or 6A1 for re-
placement procedure.
CAUTION:

Do not bend or twist timing belt.

Do not allow timing belt to come into contact with oil, wa-
ter, etc.
ITEM 1-3
Valve Lash Inspection (1.3 liter engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to SECTION 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(gap)
When cold
(Coolant temperature is
15 – 25C or 59 – 77F)When hot
(Coolant temperature is
60 – 68C or
140 – 154F)
(gap)
specifi-
cation
Intake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.17 – 0.21 mm
(0.007 – 0.008 in.)
cation
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 8.5 lb-ft)
3) Install cylinder head cover and tighten bolts to specification.

MAINTENANCE AND LUBRICATION 0B-7
Proper Engine Oil Viscosity Chart
1. Oil pan
2. Oil drain plug
1. Oil filter
ITEM 1-4
Engine Oil and Filter Change
WARNING:
New and used engine oil can be hazardous.
Be sure to read “WARNING” in General Precaution in SEC-
TION 0A and observe what in written there.
Use engine oil of SE, SF, SG, SH or SJ grade.
Select the appropriate oil viscosity according to the left chart.
Before draining engine oil, check engine for oil leakage. If any evi-
dence of leakage is found, make sure to correct defective part be-
fore proceeding to following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean. Reinstall drain plug, and
tighten it securely as specified below.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
3) Loosen oil filter by using oil filter wrench (Special tool).
Special Tool
(A): 09915-47330
4) Apply engine oil to new oil filter O-ring.
5) Screw new filter on oil filter stand by hand until filter O-ring con-
tacts mounting surface.
CAUTION:
To tighten oil filter properly, it is important to accurately
identify the position at which filter O-ring first contacts
mounting surface.
6) Tighten filter 3 / 4 turn from the point of contact with mounting sur-
face using an oil filter wrench.
Special Tool
(A): 09915-47330
Tightening Torque (Reference)
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)

2WD
4WD
1. Oil filler / level plug
2. Oil drain plug
MAINTENANCE AND LUBRICATION 0B-17
ITEM 6-7
Manual Transmission Oil Inspection and Change
[Inspection]
1) Inspect transmission case for evidence of oil leakage.
Repair leaky point if any.
2) Make sure that vehicle is placed level for oil level check.
3) Remove oil level plug of transmission.
4) Check oil level.
Oil level can be checked roughly by means of filler / level plug
hole. That is, if oil flows out of level plug hole or if oil level is found
up to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified oil up to level hole.
For specified oil, refer to description of oil change under ON-VE-
HICLE SERVICE in SECTION 7A or 7A1.
5) Tighten level plug to specified torque.
[Change]
1) Place the vehicle level and drain oil by removing drain plug.
2) Apply sealant to drain plug and tighten drain plug to specified
torque.
3) Pour specified oil up to level hole.
4) Tighten filler plug to specified torque.
For recommended oil, its amount and tightening torque data, re-
fer to ON-VEHICLE SERVICE of SECTION 7A or 7A1.
ITEM 6-8
Rear Differential Oil Inspection and Change
(4WD vehicle only)
[Inspection]
1) Inspect rear differential case for evidence of oil leakage.
Repair leaky point, if any.
2) Make sure that the vehicle is placed level for oil level check.
3) Remove level plug (1) of differential. Oil level can be checked
roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil
as given in SECTION 7E.
4) Tighten it to specified torque.
[Change]
Place the vehicle level and drain oil by removing drain plug (2). Pour
specified amount of specified oil, tighten drain plug and filler plug
to specified torque, referring to ON-VEHICLE SERVICE in SEC-
TION 7E.