2000 SUZUKI SWIFT Position sensor

0A-22 GENERAL INFORMATION
A
ABS : Anti-Lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency Locking
Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector (Assembly
Line Diag. Link, ALDL, Serial
Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control Module
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp. Sensor,
WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust
Gas Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation Heater
(Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission Canister
(Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid Valve,
ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature Sensor
(Air temperature Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL
ABBREVIATIONS

GENERAL INFORMATION 0A-23
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor (Air Flow
Sensor, AFS, Air Flow Meter,
AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure Switch
(P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic Module
(Air Bag Controller, Air Bag
Control Module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three-Way Catalytic Converter
(Three-Way Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation Catalytic
Converter
WU-TWC : Warm Up Three-Way Catalytic
Converter

Diagnostic Trouble Code Clearance 6-14. . . . .
Diagnostic Trouble Code Table 6-15. . . . . . . . .
Fail-safe Table 6-18. . . . . . . . . . . . . . . . . . . . . . .
Visual Inspection 6-19. . . . . . . . . . . . . . . . . . . . .
Engine Basic Inspection 6-20. . . . . . . . . . . . . . .
Engine Diagnosis Table 6-22. . . . . . . . . . . . . . .
Scan Tool Data 6-29. . . . . . . . . . . . . . . . . . . . . . .
Scan Tool Data Definitions 6-31. . . . . . . . . . . . .
Inspection of ECM (PCM) and Its Circuits 6-33
Voltage Check 6-33. . . . . . . . . . . . . . . . . . . . .
Resistance Check 6-37. . . . . . . . . . . . . . . . . .
Component Location 6-38. . . . . . . . . . . . . . . . . .
Table A-1 MIL Circuit Check
(Lamp does not come on) 6-39. . . . . . . . . . . .
Table A-2 MIL Circuit Check
(Lamp remains ON) 6-40. . . . . . . . . . . . . . . . . .
Table A-3 ECM (PCM) Power and Ground
Circuit Check 6-42. . . . . . . . . . . . . . . . . . . . . . .
DTC P0105 MAP Circuit Malfunction 6-44. . . .
DTC P0110 IAT Circuit Malfunction 6-46. . . . .
DTC P0115 ECT Circuit Malfunction 6-48. . . .
DTC P0120 Throttle Position Circuit
Malfunction 6-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0121 Throttle Position Circuit
Range / Performance Problem 6-52. . . . . . . . .
DTC P0130 HO2S Circuit Malfunction
(Sensor-1) 6-54. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0133 HO2S Circuit Slow
Response (Sensor-1) 6-56. . . . . . . . . . . . . . . .
DTC P0135 HO2S Heater Circuit
Malfunction (Sensor-1) 6-57. . . . . . . . . . . . . . .
DTC P0136 HO2S Circuit Malfunction
(Sensor-2) 6-59. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0141 HO2S Heater Circuit
Malfunction (Sensor-2) 6-62. . . . . . . . . . . . . . .
DTC P0171 Fuel System Too Lean 6-64. . . . .
DTC P0172 Fuel System Too Rich 6-64. . . . . .
DTC P0300 Random Misfire Detected 6-68. . .
DTC P0301 Cylinder 1 Misfire Detected 6-68. DTC P0302 Cylinder 2 Misfire Detected 6- 68.
DTC P0303 Cylinder 3 Misfire Detected 6- 68.
DTC P0335 CKP Sensor Circuit
Malfunction 6- 72. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0340 CMP Sensor Circuit
Malfunction 6- 74. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0420 Catalyst System Efficiency
Below Threshold 6- 76. . . . . . . . . . . . . . . . . . . .
DTC P0443 Purge Control Valve Circuit
Malfunction 6- 79. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0480 Radiator Fan Control
System Malfunction 6- 80. . . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction (M / T) 6- 82. . . . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction (A / T) 6- 84. . . . . . . . . . . . . . . . . . .
DTC P0505 Idle Control System
Malfunction 6- 86. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0510 Closed Throttle Position
Switch Malfunction 6- 88. . . . . . . . . . . . . . . . . .
DTC P0601 Internal Control Module
Memory Check Sum Error 6- 89. . . . . . . . . . . .
DTC P1250 EFE Heater Circuit
Malfunction 6- 90. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1450 Barometric Pressure
Sensor Low / High Input 6- 92. . . . . . . . . . . . . .
DTC P1451 Barometric Pressure Sensor
Performance Problem 6- 92. . . . . . . . . . . . . . . .
DTC P1500 Engine Starter Signal
Circuit Malfunction 6- 93. . . . . . . . . . . . . . . . . . .
DTC P1510 ECM (PCM) Back-up Power
Supply Malfunction 6- 94. . . . . . . . . . . . . . . . . .
Table B-1 Fuel Injector Circuit Check 6- 96. . . .
Table B-2 Fuel Pump and Its Circuit
Check 6- 98. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 Fuel Pressure Check 6-100. . . . . . . . .
Table B-4 A / C Signal Circuits Check 6-102. . . .
Table B-5 Power Steering Pressure
Switch Signal Circuit Check 6-103. . . . . . . . . . .
SPECIAL TOOL6-104 . . . . . . . . . . . . . . . . . . . . . . .
6-2 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)

An Example of Freeze Frame Data
1. Trouble Code P0102 (1st)
2. Engine Speed 782 RPM
3. Eng Cool Tmp. 80C
4. Vehicle Spd. 0 km/h
5. MAP Sensor 39 kPa
6. St. Term FT1– 0.8% Lean
7. Lg. Term FT1– 1.6% Lean
8. Fuel 1 Stat. Closed Loop
9. Fuel 2 Stat. Not used
10. Load value 25.5%
1st, 2nd or 3rd in parentheses here represents which
position in the order the malfunction is detected.
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-7
Warm-up Cycle
A warm-up cycle means sufficient vehicle operation such that the
coolant temperature has risen by at least 22C (40F) from engine
starting and reaches a minimum temperature of 70C (160F).
Driving Cycle
A “Driving Cycle” consists of engine startup, driving mode where a
malfunction would be detected if present and engine shutoff.
2 Driving Cycles Detection Logic
The malfunction detected in the first driving cycle is stored in ECM
(PCM) memory (in the form of pending DTC and freeze frame data)
but the malfunction indicator lamp does not light at this time. It lights
up at the second detection of same malfunction also in the next driv-
ing cycle.
Pending DTC
Pending DTC means a DTC detected and stored temporarily at 1
driving cycle of the DTC which is detected in the 2 driving cycles
detection logic.
Freeze Frame Data
ECM (PCM) stores the engine and driving conditions (in the from
of data as shown at the left) at the moment of the detection of a mal-
function in its memory. This data is called “Freeze frame data”.
Therefore, it is possible to know engine and driving conditions (e.g.,
whether the engine was warm or not, where the vehicle was running
or stopped, where air / fuel mixture was lean or rich) when a mal-
function was detected by checking the freeze frame data. Also,
ECM (PCM) has a function to store each freeze frame data for three
different malfunctions in the order as the malfunction is detected.
Utilizing this function, it is possible to know the order of malfunctions
that have been detected. Its use is helpful when rechecking or diag-
nosing a trouble.
Priority of freeze frame data:
ECM (PCM) has 4 frames where the freeze frame data can be
stored. The first frame stores the freeze frame data of the malfunc-
tion which was detected first. However, the freeze frame data
stored in this frame is updated according to the priority described
below. (If malfunction as described in the upper square “1” below
is detected while the freeze frame data in the lower square “2” has
been stored, the freeze frame data “2” will be updated by the freeze
frame data “1”.)
PRIORITY
FREEZE FRAME DATA IN FRAME 1
1
Freeze frame data at initial detection of malfunction
among misfire detected (P0300-P0303), fuel
system too lean (P0171) and fuel system too rich
(P0172)
2Freeze frame data when a malfunction other than
those in “1” above is detected

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-15
DIAGNOSTIC TROUBLE CODE (DTC) TABLE
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0105Manifold absolute pressure
circuit malfunction
Low pressure-high vacuum-low voltage
(or MAP sensor circuit shorted to ground)
High pressure-low vacuum-high voltage
(or MAP sensor circuit open)
1 driving cycle
P0110Intake air temp. circuit
malfunctionIntake air temp. circuit low input
Intake air temp. circuit high input1 driving cycle
P0115Engine coolant temp. circuit
malfunctionEngine coolant temp. circuit low input
Engine coolant temp. circuit high input1 driving cycle
P0120Throttle position circuit
malfunctionThrottle position circuit low input
Throttle position circuit high input1 driving cycle
P0121Throttle position circuit
performance problemPoor performance of TP sensor2 driving cycles
P0130HO2S circuit malfunction
(Sensor-1)
Min. output voltage of HO2S-higher than
specification
Max. output voltage of HO2S-lower than
specification
2 driving cycles
P0133HO2S circuit slow response
(Sensor-1)Response time of HO2S-1 output voltage
between rich and lean is longer than
specification.
2 driving cycles
P0135HO2S heater circuit
malfunction (Sensor-1)Terminal voltage is lower than specification
at heater OFF or it is higher at heater ON.2 driving cycles
P0136HO2S circuit malfunction
(Sensor-2)Max. voltage of HO2S-2 is lower than
specification or its min. voltage is higher than
specification
2 driving cycles
P0141HO2S heater circuit
malfunction (Sensor-2)Terminal voltage is lower than specification
at heater OFF or it is higher at heater ON.
(or heater circuit or short)
2 driving cycles
P0171Fuel system too lean
Short term fuel trim or total fuel trim (short
and long terms added) is larger than
specification for specified time or longer.
(fuel trim toward rich side is large.)
2 driving cycles
P0172Fuel system too rich
Short term fuel trim or total fuel trim (short
and long term added) is smaller than
specification for specified time or longer.
(fuel trim toward lean side is large.)
2 driving cycles
P0300
P0301
P0302
Random misfire detected
Cylinder 1 misfire detected
Cylinder 2 misfire detected
Misfire of such level as to cause damage to
three way catalystMIL flashing
during misfire
detection
P0302
P0303
Cylinder 2 misfire detected
Cylinder 3 misfire detectedMisfire of such level as to deteriorate emission
but not to cause damage to three way catalyst2 driving cycles

6-16 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0335Crankshaft position sensor
circuit malfunctionNo signal during engine running1 driving cycle
P0340Camshaft position sensor
circuit malfunctionNo signal for 2 sec. during engine cranking1 driving cycle
P0420Catalyst system efficiency
below threshold
Output waveforms of HO2S-1 and HO2S-2
are similar.
(Time from output voltage change of HO2S-1
to that of HO2S-2 is shorter than
specification.)
2 driving cycles
P0443EVAP Purge control valve
circuit malfunctionPurge control valve circuit is open or shorted
to ground2 driving cycles
P0480Radiator fan control circuit
malfunctionRadiator cooling fan relay terminal voltage is
low when cooling temp. is lower than
specification
2 driving cycles
P0500Vehicle speed sensor
malfunctionNo signal while running in “D” range or during
fuel cut at decelerating2 driving cycles
P0505Idle control system malfunction
Throttle opening change is small as compared
with electrically live time. Throttle valve opening
is not within its target range with CTP switch ON
or drive voltage exists though ECM (PCM) is not
outputting ISC drive command.
1 driving cycle
P0510Closed throttle position switch
malfunctionSwitch does not change from ON to OFF
(or from OFF to ON) even when vehicle speed
reaches over (or below) specification.
2 driving cycle
P1250Early Fuel Evaporation Heater
Circuit MalfunctionHeater monitor terminal voltage is higher than
specified value when EFE OFF or it is lower
than specified value when EFE ON.
2 driving cycles
P1450Barometric pressure sensor
circuit malfunctionBarometric pressure is lower or higher than
specification. (or sensor malfunction)1 driving cycle
P1451Barometric pressure sensor
performance problem
Difference between manifold absolute
pressure (MAP sensor value) and
barometric pressure (barometric pressure
sensor value) is larger than specification
during cranking.
2 driving cycles
P1500Starter signal circuit
malfunctionStarter signal is not inputted from engine
cranking till its start and after or it is always
inputted
2 driving cycles
P1510ECM (PCM) backup power
source malfunctionNo backup power after starting engine1 driving cycle

6-18 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
FAIL-SAFE TABLE
When any of the following DTCs is detected, ECM (PCM) enters fail-safe mode as long as malfunction continues
to exist but that mode is canceled when ECM (PCM) detects normal condition after that.
DTC NO.
DETECTED ITEMFAIL-SAFE OPERATION
P0105Manifold absolute pressure circuit
malfunction
ECM (PCM) uses value determined by throttle
opening and engine speed.

ECM (PCM) stops EVAP purge control.
P0110Intake air temp. circuit malfunctionECM (PCM) controls actuators assuming that
intake air temperature is 20C (68F).
P0115Engine coolant temp. circuit malfunction

ECM (PCM) controls actuators assuming that
engine coolant temperature is 80C (176F).

ECM (PCM) operates radiator fan.

ECM (PCM) stops A / C and idle speed control.
P0120Throttle position circuit malfunction

ECM (PCM) controls actuators assuming that
throttle opening is 20.

ECM (PCM) stops idle speed control.
P0500Vehicle speed sensor malfunctionECM (PCM) stops idle air control.
P1450Barometric pressure sensor low /
high inputECM (PCM) controls actuators assuming that
barometric pressure is 100 kPa (760 mmHg).

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-29
Ambient temp.
SCAN TOOL DATA
As the data values given below are standard values estimated on the basis of values obtained from the normally
operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition,
there may be cases where the checked value does not fall within each specified data range. Therefore, judgment
as abnormal should not be made by checking with these data alone.
Also, conditions in the below table that can be checked by the scan tool are those detected by ECM (PCM) and
output from ECM (PCM) as commands and there may be cases where the engine or actuator is not operating (in
the condition) as indicated by the scan tool. Be sure to use the timing light to check the ignition timing.
NOTE:

With the generic scan tool, only star () marked data in the table below can be read.

When checking the data with the engine running at idle or racing, be sure to shift M / T gear to the neutral
gear position and A / T gear to the “Park” position and pull the parking brake fully. Also, if nothing or “no
load” is indicated, turn OFF A / C, all electric loads, P / S and all the other necessary switches.
SCAN TOOL DATAVEHICLE CONDITIONNORMAL CONDITION /
REFERENCE VALUES
FUEL SYSTEM B1 (FUEL
SYSTEM STATUS)At specified idle speed after warming upCLOSED (closed loop)

CALC LOAD
(CALCULATED LOADAt specified idle speed with no load after
warming up3 – 5%(
VALUE)At 2500 r / min with no load after warming up10 – 18%

COOLANT TEMP.
(ENGINE COOLANT
TEMP.)
At specified idle speed after warming up85 – 95C, 185 – 203F
SHORT FT BI (SHORT
TERM FUEL TRIM)At specified idle speed after warming up–20 – +20%
LONG FT BI (LONG
TERM FUEL TRIM)At specified idle speed after warming up–15 – +15%

MAP (INTAKE
MANIFOLD ABSOLUTE
PRESSURE)At specified idle speed with no load after
warming up29 – 48 kPa,
220 – 360 mmHg
ENGINE SPEEDAt idling with no load after warming upDesired idle speed
± 50 r / min
VEHICLE SPEEDAt stop0 km / h, 0 MPH

IGNITION ADVANCE
(IGNITION TIMING
ADVANCE FOR NO.1
CYLINDER)
At specified idle speed with no load after
warming up–1 – 18 BTDC
INTAKE AIR TEMP.At specified idle speed after warming up+35C (+63F)
–5C (–9F)
MAF (MASS AIR FLOW
RATE)
At specified idle speed with no load after
warming up1.0 – 3.0 gm / sec
RATE)At 2500 r / min with no load after warming up3.0 – 6.0 gm / sec

THROTTLE POS
(ABSOLUTEIgnition switch ON /Throttle valve fully closed7 – 18%
(ABSOLUTE
THROTTLE POSITION)
g
engine stoppedThrottle valve fully open70 – 90%
O2S B1 S1 (HEATED
OXYGEN SENSOR-1)At specified idle speed after warming up0.05 – 0.95 V
O2S B1 S2 (HEATED
OXYGEN SENSOR-2)When engine is running at 2000 r / min. for
3 min. or longer after warming up.0 – 0.95 V
O2S FT B1 S1At specified idle speed after warning up–20 – +20%
DIS. WITH MIL ON————