2000 SUZUKI SWIFT Tightening Torque

(b)
(a)
6A1-18 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
INSTALLATION
1) Install new gaskets to cylinder head.
2) Install exhaust manifold.
Tighten bolts and nuts to specified torque.
Tightening Torque
(a): 32 N
.m (3.2 kg-m, 23.5 lb-ft)
3) Install exhaust manifold cover(s) (1).
4) Connect oxygen sensor coupler (3) and clamp (2) its wire se-
curely.
5) Tighten exhaust No.1 pipe to manifold nuts and exhaust man-
ifold stiffener bolt.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
6) Connect negative cable at battery.
7) Check exhaust system for exhaust gas leakage.

1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Camshaft timing pulley
6. Tensioner bolt
7. Pulley bolt
8. Seal
9. Inside cover seal
10. Inside cover
11. Outside cover seal
12. Outside cover
13. Tensioner stud
14. Damper
1. Water pump pulley
: Tightening Torque
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-19
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Remove right side of engine under cover.
3) Remove power steering pump belt or A / C compressor belt, if
equipped.
4) Disconnect IAT sensor at coupler.
5) Remove air cleaner case with air cleaner outlet hose.
6) Remove power steering hose stay (1) (if equipped).
7) Remove water pump pulley and drive belt.

1. Clamp
1. Long bolt
2. Short bolt
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-23
6) To take up slack of timing belt, turn crankshaft two rotations
clockwise after installing it. After making sure that belt is free
from slack, tighten tensioner stud first and then tensioner bolt
to each specified torque.
Then confirm again that two sets of marks are aligned respec-
tively.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
7) Install timing belt outside cover.
Before installing, make sure that seal is between water pump
and oil pump case.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
8) With crankshaft locked, remove crankshaft timing belt pulley
bolt (4).
9) Install crankshaft pulley (2).
Fit hole of pulley to pin (1) on crankshaft timing belt pulley, and
tighten pulley bolts (3) to specified torque.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
10) With crankshaft locked using flat end rod or the like, tighten
crankshaft timing belt pulley bolt (4).
Tightening Torque
(b): 130 N
.m (13.0 kg-m, 94.0 lb-ft)
11) Clamp harness securely.

6A1-24 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
12) Install water pump pulley (1) and drive belt.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
13) Adjust drive belt tension referring to Section 6B.
14) Adjust power steering pump belt tension or A/C compressor
belt tension, if equipped.
Refer to Section 0B.
15) Install P / S hose stay (if equipped).
16) Install air cleaner case with air cleaner outlet hose.
17) Install right side of engine under cover.
18) Install clutch housing (torque converter housing for A / T) lower
plate.
19) Connect negative cable at battery.

1. Oil pan:
Apply sealant 99000-31150 to
oil pan mating surface.
2. Oil pump strainer
3. Seal
4. Drain plug gasket
5. Drain plug
6. CKP sensor : Tightening Torque
: Do not reuse
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-25
OIL PAN AND OIL PUMP STRAINER
REMOVAL
1) Raise vehicle.
2) Drain engine oil by removing drain plug (1).
3) Remove right side of engine under cover.
4) Disconnect CKP sensor coupler and remove CKP sensor (1) by
removing its bolt. Then remove CKP sensor wire harness from
clamp.
5) Remove clutch housing (torque converter housing for A / T) low-
er plate.

2. O-ring
6A1-26 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
6) Remove oil pan (3) and then oil pump strainer (1).
CLEANING

Clean mating surfaces of oil pan and cylinder block.
Remove oil, old sealant, and dusts from mating surfaces and oil
pan inside.

Clean oil pump strainer screen.
INSTALLATION
1) Apply sealant to oil pan mating surface continuously as shown
in figure.
“A” Sealant: 99000-31150
Sealant amount
Width “a”: 4 mm, 0.16 in.
Height “b”: 2 mm, 0.08 in.
2) Install O-ring (2) into cylinder block securely as shown in figure.
Install oil pump strainer (1) to cylinder block.
Tighten strainer bolt first and then bracket bolt to specified
torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
After fitting oil pan (3) to cylinder block, run in securing bolts and
start tightening at the center: move wrench outward, tightening
one bolt at a time.
Tighten bolts to specified torque.
Tightening Torque
(b): 11 N
.m (1.1 kg-m, 8.0 lb-ft)

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-27
3) Install new gasket and drain plug to oil pan.
Tighten drain plug to specified torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36 lb-ft)
4) Install clutch (torque converter) housing lower plate.
5) Install CKP sensor (1) and connect its coupler, then clamp its
harness.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
6) Install right side of engine under cover.
7) Refill engine with engine oil referring to “ENGINE OIL CHANGE”
in Section 0B.

1. Rotor plate
2. Inner rotor:
Apply thin coat of engine oil.
3. Outer rotor:
Apply thin coat of engine oil.
4. Gasket
5. Pin
6. Pin
7. Relief valve:
Apply thin coat of engine oil.
8. Spring
9. Retainer
10. Retainer ring
11. Front oil seal:
Apply engine oil to contact
part of crankshaft with oil seal lip.
12. Plate screw
13. Bolt (short)
14. Bolt (long)
: Tightening Torque
: Do not reuse
6A1-28 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
OIL PUMP
REMOVAL
1) Disconnect negative cable at battery.
2) Remove timing belt as previously outlined.
3) Remove generator and its bracket.
NOTE:
When installing bracket, fasten nut (A) first.
4) Remove power steering pump bracket or A / C compressor
bracket, if equipped.
NOTE:
When installing bracket, fasten bolt (B) first.
5) Remove oil pan and oil pump strainer as previously outlined.
6) Remove crankshaft timing belt pulley (3).
Lock crankshaft inserting flat end rod or the like (1) between fly-
wheel ring gear and transmission case.
With crankshaft locked, remove crankshaft timing belt pulley
bolt (2).