2000 SUZUKI SWIFT Exhaust

[For 1.0
2WD N / B model]
[For 1.3
2WD H / B model]
: Do not reuse
: Tightening Torque 6. Exhaust No.2 pipe
7. Gasket
8. Muffler
9. Muffler mounting
10. Heated oxygen sensor
11. Exhaust center pipe 1. Exhaust manifold
2. Seal
3. WU-TWC
4. Exhaust pipe
5. Exhaust No.1 pipe
6K-2 EXHAUST SYSTEM

: Do not reuse
: Tightening Torque 1. Exhaust manifold
2. Seal
3. Exhaust No.1 pipe
4. Exhaust No.2 pipe
5. Gasket
6. Exhaust center pipe7. Muffler
8. Muffler mounting
9. Heated oxygen sensor
[For 1.3
4WD model] [For 1.3
2WD N / B model]
45 N.m (4.5 kg-m)
EXHAUST SYSTEM 6K-3

1. Malfunction indicator lamp (MIL)
2. Data link connector (DLC)
3. SUZUKI scan tool (Tech-1)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-11
DIAGNOSIS
This vehicle is equipped with an electronic transmission control system, which control the automatic shift up and
shift down timing, etc. suitably to vehicle driving conditions.
PCM (ECM) has an On-Board Diagnosis System which detects a malfunction in this system and abnormality of
those parts that influence the engine exhaust emission.
When diagnosing a trouble in transmission including this system, be sure to have full understanding of the outline
of “ON-BOARD DIAGNOSTIC SYSTEM” and each item in “PRECAUTION IN DIAGNOSING TROUBLE” and
execute diagnosis according to “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW TABLE” given below to ob-
tain correct result smoothly.
ON-BOARD DIAGNOSTIC SYSTEM
For automatic transmission control system, PCM (ECM) has follow-
ing functions. Refer to Section 6 or 6-1 for details.

When ignition switch is turned ON with engine at a stop malfunc-
tion indicator lamp (MIL) turns ON to check bulb of MIL.

When PCM detects a malfunction in A / T control system (and / or
a malfunction which gives an adverse effect to vehicle emission)
while engine is running, it makes malfunction indicator lamp in
meter cluster of instrument panel turn ON and stores malfunction
area (DTC) in its memory.
If it detects that continuously 3 driving cycles are normal after de-
tecting a malfunction, however, it makes MIL turn OFF although
DTC stored in its memory will remain.

It is possible to communicate with PCM through data link connect-
er (DLC) by using SUZUKI scan tool (Tech-1).
(Diagnostic information can be checked and erased by using a
scan tool)
2 Driving Cycle Detection Logic
Refer to Section 6 or 6-1 for details.
Freeze Frame Data
Refer to Section 6 or 6-1 for details.

WITHOUT BATTERY VOLTAGE
WITH BATTERY VOLTAGE
1. Oiler (with transmission fluid)
2. Solenoid valve
3. 12V battery
“A”: Side hole (Should be dry)
“B”: Exhausting fluid
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-37
“P” RANGE TEST
1) Stop vehicle on a slope, shift selector lever to P range and at the
same time apply parking brake.
2) After stopping engine, release parking brake lever gradually and
check that vehicle remains stationary.
SHIFT SOLENOID VALVE CHECK
Whenever shift solenoid valves are removed from transmission,
verify their valve function physically before they are reinstalled.
1) Apply oiler to solenoid valve and give compression by hands
and then check to be sure that transmission fluid from oiler does
not come out from side holes of solenoid valve when battery volt-
age is not conducted.
2) Holding the above condition, conduct battery voltage and then
make sure that fluid is exhausted with vigor.
NOTE:
If fluid does not come out with vigor in above step 2) inspec-
tion, do not reuse that solenoid valve.