2000 SUZUKI SWIFT radiator

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-9
FUEL PUMP RELAY
FUEL INJECTOR
HO2S HEATER
IAC VALVE
IGNITION COIL WITH IGNITER
EGR VALVE
EVAP CANISTER PURGE VALVE
A/C CONTROL MODULE
RADIATOR FAN RELAY
MIL
MAIN RELAY
SIGNAL FROM SENSOR, SWITCH AND CONTROL MODULE
OUTPUT
INPUT
ENGINE & EMISSION CONTROL INPUT / OUTPUT TABLE
ELECTRIC CONTROL DEVICE
FUEL LEVEL SENSORFor detecting fuel level
BAROMETRIC PRESSURE SENSOR
START SWITCH
IGNITION SWITCH
LIGHTING SWITCH
REAR DEFOGGER SWITCH (IF EQUIPPED)
BLOWER SWITCH
A / C SWITCH
VSS
HEATED OXYGEN SENSOR-1
HEATED OXYGEN SENSOR-2For detecting deterioration of
three way catalytic convertor
IAT SENSOR
ECT SENSOR
TP SENSOR
MAP SENSOR
CMP SENSOR
CKP SENSOR

12 W / R “N”-range signal (A / T)
13 R Heated oxygen sensor-2
14 Y / R “D”-range signal (A / T)
15 R / W “R”-range signal (A / T)
16 Lg / B A / C SW signal
17 R / W EGR valve (stepper motor coil 4)
18 P / G Radiator fan relay
19 Y / Bl Fuel pump relay
20 —— ———
21 W / B “P”-range signal (A / T)
22 P / Bl Fuel level gauge
23 R / B “L”-range signal (A / T)
24 —— ———
1 V Malfunction indicator lamp
Vehicle speed sensor (M / T)
Output shaft speed sensor (+)
(A / T)
3 —— ———
4 G / W Shift solenoid – A (A / T)
5 Gr Throttle position (TP) sensor
6 B / W Ignition switch signal
7 Y / B Data link connector
Output shaft speed sensor (–)
(A / T)
9 —— ———
10 G GND for HO2S-2
11 G / Or Shift solenoid – B (A / T)
12 —— ———
13 —— ———
14 —— ———
15 —— ———
16 Br Tachometer signal
17 B / Y Engine start signal
CON-
NECTORTERMINALWIRE
COLORCIRCUITCON-
NECTORTERMINALWIRE
COLORCIRCUIT
20
Br / Y 19
Br / W
C02 C01C02
C03
Wire color
B : Black
B / Or : Black / Orange
B / W : Black / White
B / Y : Black / Yellow
Bl : Blue
Bl / Or : Blue / Orange
Bl / B : Blue / Black
Bl / R : Blue / Red
Bl / Y : Blue / Yellow
Br : Brown
Br / W : Brown / White
Br / Y : Brown / Yellow
G : Green
G / Or : Green / Orange
G / R : Green / Red
G / W : Green / White
Gr : Gray
Gr / R : Gray / Red
Lg / B : Lightgreen / Black
Lg / R : Lightgreen / RedP : Pink
P / Bl : Pink / Blue
P / G : Pink / Green
V : Violet
V / G : Violet / Green
V / R : Violet / Red
V / W : Violet / White
W : White
W / B : White / Black
W / R : White / Red
R : Red
R / B : Red / Black
R / Bl : Red / Blue
R / G : Red / Green
R / W : Red / White
R / Y : Red / Yellow
Y / B : Yellow / Black
Y / Bl : Yellow / Blue
Y / R : Yellow / Red
2
P
8
Bl
6E2-12 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
1 B Ground for ECM / PCM
2 B / Or Ground for drive circuit
3 B / Or Ground for drive circuit
4 V / R Canister purge valve
5 G / W Power steering pressure switch
6 V / W IAC valve
7 Bl Heater of HO2S-1
8 Bl / Or No.4 fuel injector
9 Bl / R No.1 fuel injector
10 G Ground for sensor circuit
11 B / W CMP sensor
12 —— ———
13 R Heated oxygen sensor-1
14 Lg / R Coolant temp. sensor
15 Gr / R Intake air temp. sensor
16 —— ———
17 Br / Y Electric load (+)
18 —— ———
IG coil assembly for
No.2 and 3 spark plugs
IG coil assembly for
No.1 and 4 spark plugs
21 Bl / B No.2 fuel injector
22 P Power supply for sensor
23 W CKP sensor (+)
24 B CKP sensor (–)
25 —— ———
26 G MAP sensor
27 —— ———
28 V / G Immobilizer indicator lamp
29 —— ———
30 —— ———
31 Bl / Y No.3 fuel injector
1 G / R A / C compressor clutch
2 R / Y EGR valve (stepper motor coil 1)
3 R / G Data link connector
4 Lg / B Heater of HO2S-2
5 R / B Power source
6 R / B Power source
7 W Backup power source
8 R EGR valve (stepper motor coil 3)
9 R / Bl EGR valve (stepper motor coil 2)
10 Gr Ground for main relay
11 Y / B “2”-range signal (A / T)

2.297 – 2.595
0.298 – 0.320
6E2-30 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
ENGINE COOLANT TEMPERATURE SENSOR
(ECT SENSOR)
Removal
1) Disconnect battery negative cable at battery.
2) Drain coolant referring to Section 6B.
WARNING:
To help avoid danger of being burned, do not remove ra-
diator cap while engine and radiator are still hot.
Scalding fluid and steam can be blown out under pres-
sure if cap is taken off too soon.
3) Disconnect coupler from ECT sensor.
4) Remove ECT sensor (1) from thermostat case.
Inspection
Immerse temperature sensing part of ECT sensor (1) in water (or
ice) and measure resistance between terminal “A” and “B” while
heating water gradually.
If measured resistance doesn’t show such characteristic as shown
in left figure, replace ECT sensor (1).
Installation
Reverse removal procedure noting the following:

Clean mating surfaces of ECT sensor (1) and thermostat case.

Check O-ring for damage and replace if necessary.

Tighten ECT sensor (1) to specified torque.
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 9.0 lb-ft)

Connect coupler to ECT sensor (1) securely.

Refill coolant referring to Section 6B.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-33
VEHICLE SPEED SENSOR (VSS)
Inspection
Check vehicle speed sensor referring to step 3 of DTC P0500 Flow
Table. If malfunction is found, replace.
Removal / Installation
Refer to Section 7A.
FUEL LEVEL SENSOR (GAUGE)
Inspection
Refer to Section 8.
Removal / Installation
Refer to Section 6C.
MAIN RELAY, FUEL PUMP RELAY AND RADIATOR
FAN CONTROL RELAY
Inspection
1) Disconnect negative cable at battery.
2) Remove main relay (1), fuel pump relay (2) and radiator fan con-
trol relay (3) from relay box.
3) Check that there is no continuity between terminal “c” and “d”.
If there is continuity, replace relay.
4) Connect battery positive (+) terminal to terminal “b” of relay.
Connect battery negative (–) terminal “a” of relay.
Check continuity between terminal “c” and “d”.
If there is no continuity when relay is connected to the battery,
replace relay.

6E2-34 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
FUEL CUT OPERATION
Inspection
NOTE:
Before inspection, check to make sure that gear shift lever is
in neutral position (with A / T model, selector lever in “P”
range), A / C is OFF and that parking brake lever is pulled all the
way up.
1) Warm up engine to normal operating temperature.
2) While listening to sound of injector (1) by using sound scope (2)
or such, increase engine speed to higher than 3,000 r / min.
3) Check to make sure that sound to indicate operation of injector
stops when throttle valve is closed instantly and it is heard again
when engine speed is reduced to less than about 2,000 r / min.
RADIATOR FAN CONTROL SYSTEM
System Inspection
WARNING:
Keep hands, tools, and clothing away from engine cooling
fan to help prevent personal injury. This fan is electric and
can come on whether or not the engine is running. The fan
can start automatically in response to the ECT sensor with
the ignition switch in the ON position.
Check system for operation referring to Flow Table B-8 in Section
6.
If radiator fan fails to operate properly, check relay, radiator fan and
electrical circuit.
Radiator Fan
Inspection
1) Check continuity between each two terminals.
If there is no continuity, replace radiator fan motor.

1
2
1. SUZUKI scan tool display
2. EGR valve opening (0: Close, 100: Full Open)
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-35
2) Connect battery (1) to radiator fan motor coupler (2) as shown
in figure, then check that the radiator fan motor operates
smoothly.
If radiator fan motor does not operate smoothly, replace motor.
EMISSION CONTROL SYSTEM
EGR SYSTEM
System Inspection (using SUZUKI scan tool)
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and then select “DATA LIST” mode on
scan tool.
3) Make sure that vehicle condition is as following.

Vehicle speed = 0 KPH

Engine coolant temp.
80C

Engine speed  3000 rpm
4) Clear DTC by using “CLEAR INFO” mode.
5) With engine idling (without depressing accelerator pedal), open
EGR valve by using “STEP EGR” mode in “MISC TEST” menu.
In this state, according as EGR valve opening increases engine
idle speed drops. If not, possible cause is clogged EGR gas pas-
sage, stuck or faulty EGR valve, poor performance of ECT sen-
sor or TP sensor or DTC and / or pending DTC is (are) stored in
ECM memory.
Removal
1) Disconnect negative cable at battery.
2) Disconnect EGR valve coupler.
3) Remove EGR valve and gasket from intake manifold.