2000 SUZUKI SWIFT CHECK

6A1-40 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
1. O-ring2
10) Using special tool, tighten pulley bolt to specified torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
Special Tool
(A): 09917-68221
11) Install belt tensioner, timing belt, outside cover, crankshaft
pulley and water pump belt as previously outlined.
12) After applying sealant to part “A” as shown in figure, install
CMP sensor case (2) (Distributorless ignition coil case) to cyl-
inder head and tighten its fixing bolts to specified torque.
“A” Sealant: 99000-31110
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
13) Adjust valve clearance as previously outlined.
14) Install cylinder head cover and air cleaner outlet hose.
15) Check to ensure that the following parts are back in place:

Ignition coil assemblies

High tension cords

CMP sensor coupler

Couplers to ignition coil assembly

Other removed parts which have not been reinstalled
16) Connect negative cable at battery.
17) Confirm that ignition timing is within specification referring to
Section 6F.

3
2. Breather hose
3. PCV valve4. High-tension cords
5. Ignition coil assembly
6. Ignition coil coupler
A: Camshaft pulley side
B: CMP sensor case side
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-43
9) Remove cylinder head cover (1) as previously outlined.
Loosen all valve lash adjusting screws fully.
10) Remove timing belt and camshaft as previously outlined.
11) Disconnect exhaust pipe from exhaust manifold and remove
exhaust manifold stiffener (if equipped).
12) Loosen cylinder head bolts in such order as indicated in figure
and remove them.
13) Check all around cylinder head for any other parts required to
be removed or disconnected and remove or disconnect what-
ever necessary.
14) Remove cylinder head with intake manifold, exhaust manifold
CMP sensor case, using lifting device if necessary.

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-45
INSPECTION
Valve Guides
Using a micrometer and bore gauge, take diameter readings on
valve stems and guides to check stem-to-guide clearance.
Be sure to take reading at more than one place along the length of
each stem and guide.
If clearance exceeds limit, replace valve and valve guide.
Item
StandardLimit
Valve stemIn5.465 – 5.480 mm
(0.2152 – 0.2157 in.)–
diameterEx5.440 – 5.455 mm
(0.2142 – 0.2148 in.)–
Valve guideIn5.500 – 5.512 mmg
I.D.Ex(0.2166 – 0.2170 in.)–
Stem-to-guideIn0.020 – 0.047 mm
(0.0008 – 0.0018 in.)0.07 mm
(0.0027 in.)
g
clearanceEx0.045 – 0.072 mm
(0.0018 – 0.0028 in.)0.09 mm
(0.0035 in.)
If bore gauge is not available, check end deflection of valve stem
with a dial gauge instead.
Move stem end in directions (1) and (2) to measure end deflection.
If deflection exceeds its limit, replace valve stem and valve guide.
Valve stem end
In0.14 mm (0.005 in.)
deflection limitEx0.18 mm (0.007 in.)
Valves

Remove all carbon from valves.

Inspect each valve for wear, burn or distortion at its face and stem
and, as necessary, replace it.

Measure thickness “a” of valve head. If measured thickness ex-
ceeds limit, replace valve.
Valve head thickness
StandardLimit
In0.8 – 1.2 mm0.6 mm (0.024 in.)
Ex(0.03 – 0.047 in.)0.7 mm (0.027 in.)

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-47

Valve seat repair:
A valve seat (2) not producing a uniform contact with its valve or
showing width of seating contact that is out of specified range
must be repaired by regrinding or by cutting and regrinding and
finished by lapping.
1) EXHAUST VALVE SEAT: Use valve seat cutters (1) to make
two cuts as illustrated in figure. Two cutters must be used: the
first for making 15 angle, and the second for making 45
angle. The second cut must be made to produce desired seat
width.
Seat width for exhaust valve seat:
1.1 – 1.3 mm (0.0433 – 0.0512 in.)
2) INTAKE VALVE SEAT: Cutting sequence is the same as for ex-
haust valve seats.
Seat width for intake valve seat:
1.1 – 1.3 mm (0.0433 – 0.0512 in.)
3) VALVE LAPPING: Lap valve on seat in two steps, first with
coarse size lapping compound applied to face and the second
with fine-size compound, each time using valve lapper accord-
ing to usual lapping method.
Cylinder Head

Remove all carbon from combustion chambers.
NOTE:
Do not use any sharp-edged tool to scrape off carbon. Be
careful not to scuff or nick metal surfaces when decarbon-
ing. The same applies to valves and valve seats, too.

Check cylinder head for cracks in intake and exhaust ports, com-
bustion chambers, and head surface.

6A1-48 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)

Flatness of gasketed surface:
Using a straightedge and thickness gauge, check surface at a to-
tal of 6 locations. If distortion limit, given below, is exceeded, cor-
rect gasketed surface with a surface plate and abrasive paper of
about #400 (Waterproof silicon carbide abrasive paper): place
paper on and over surface plate, and rub gasketed surface
against paper to grind off high spots. Should this fail to reduce
thickness gauge readings to within limit, replace cylinder head.
Leakage of combustion gases from this gasketed joint is often
due to warped gasketed surface: such leakage results in reduced
power output.
Limit of distortion: 0.05 mm (0.002 in.)

Distortion of manifold seating faces:
Check seating faces of cylinder head for manifolds, using a
straightedge and thickness gauge, in order to determine whether
these faces should be corrected or cylinder head replaced.
Limit of distortion: 0.10 mm (0.004 in.)

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-49
Valve Springs

Referring to data given below, check to be sure that each spring
is in sound condition, free of any evidence of breakage or weak-
ening. Remember, weakened valve springs can cause chatter,
not to mention possibility of reducing power output due to gas
leakage caused by decreased seating pressure.
Item
StandardLimit
Valve spring
free length36.83 mm
(1.4500 in.)35.67 mm
(1.4043 in.)
Valve spring
preload10.7 – 12.5 kg for
31.5 mm (23.6 –
27.5 lb / 1.24 in.)9.3 kg for 31.5 mm
(20.5 lb / 1.24 in.)

Spring squareness:
Use a square and surface plate to check each spring for square-
ness in terms of clearance between end of valve spring and
square. Valve springs found to exhibit a larger clearance than limit
given below must be replaced.
Valve spring squareness limit: 1.6 mm (0.063 in.)

A: Valve spring retainer side
B: Valve spring seat side
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-51
5) Install new valve stem seal (1) to valve guide.
After applying engine oil to seal and spindle of special tool (Valve
guide installer handle), fit oil seal to spindle, and then install seal
to valve guide by pushing special tool by hand.
After installing, check to be sure that seal is properly fixed to
valve guide.
Special Tool
(A): 09917-98221
(B): 09916-58210
NOTE:

Do not reuse seal once disassembled. Be sure to install
new seal.

When installing, never tap or hit special tool with a ham-
mer or else. Install seal to guide only by pushing special
tool by hand. Tapping or hitting special tool may cause
damage to seal.
6) Install valve to valve guide.
Before installing valve to valve guide, apply engine oil to stem
seal, valve guide bore, and valve stem.
7) Install valve spring and spring retainer.
Each valve spring has top end (large-pitch (1) end) and bottom
end (small-pitch (2) end). Be sure to position spring in place with
its bottom end (small-pitch end) facing the bottom (valve spring
seat side).
8) Using special tools (Valve lifter), compress valve spring and fit
two valve cotters (1) into groove in valve stem.
Special Tool
(A): 09916-14510
(B): 09916-14910
(C): 09916-84511

A: Crankshaft pulley side
B: Flywheel side
A: Camshaft pulley side
B: CMP sensor case side
6A1-52 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
9) Install rocker arms, washers, rocker arm shaft and camshaft as
previously outlined.
10) Install CMP sensor case, intake manifold and exhaust man-
ifold.
INSTALLATION
1) Remove oil gasket and oil on mating surfaces and install new
head gasket (1) as shown in figure, that is, “TOP” mark provided
on gasket comes to crankshaft pulley side, facing up (toward cyl-
inder head side).
2) Check to make sure that oil jet (venturi plug) is installed and if
it is, that it is not clogged.
When installing it, be sure to tighten to specified torque.
Tightening Torque
(a): 3.5 N
.m (0.35 kg-m, 2.5 lb-ft)
3) Apply engine oil to cylinder head bolts and tighten them gradual-
ly as follows.
a) Tighten all bolts to 35 N
.m (3.5 kg-m, 25.0 lb-ft) according to
numerical order in figure.
b) In the same manner as in a), tighten them to 55 N
.m
(5.5 kg-m, 40.0 lb-ft).
c) Loosen all bolts until tightening torque is reduced to 0 (zero)
in reverse order of tightening.
d) In the same manner as in a), tighten them to 35 N
.m
(3.5 kg-m, 25.0 lb-ft).
e) In the same manner as in a) again, tighten them to specified
torque.
Tightening Torque
(a): 68 N
.m (6.8 kg-m, 49.5 lb-ft)