2000 SUZUKI SWIFT ısc

1
2
3
1. Ground terminal
2. Reference voltage terminal
3. Output voltage terminal
(a)
1
23
4
6E2-28 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
THROTTLE POSITION SENSOR (TP SENSOR)
Inspection
1) Disconnect negative cable at battery and coupler from TP sen-
sor.
2) Using ohmmeter, check resistance between terminals under
each condition given in table below.
TERMINALS
RESISTANCE
Between 1 and
2 terminals2.5 – 6.0 kΩ
Between 1 and
Throttle valve is
at idle position0.17 – 11.4 kΩ
3 terminalsThrottle valve is
fully opened1.72 – 15.50 kΩ
NOTE:
There should be more than 1.5 kΩ resistance difference
between when throttle valve is at idle position and when
it is fully open.
If check result is not satisfactory, replace TP sensor.
3) Connect TP sensor coupler securely.
4) Connect negative cable to battery.
Removal
1) Disconnect battery negative cable at battery.
2) Disconnect coupler from TP sensor.
3) Remove TP sensor from throttle body.
Installation
1) Install TP sensor (1) to throttle body.
Fit TP sensor to throttle body in such way that its holes (3) are
a little away from TP sensor screw holes (2) as shown in left fig-
ure and turn TP sensor clockwise so that those holes align (4).
Tightening Torque
(a): 2.0 N
.m (0.20 kg-m, 1.5 lb-ft)
2) Connect coupler to TP sensor securely.
3) Connect battery negative cable to battery.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-29
INTAKE AIR TEMPERATURE SENSOR (IAT SENSOR)
Removal
1) Disconnect battery negative cable at battery.
2) Disconnect coupler from IAT sensor (1).
3) Remove IAT sensor (1) from air cleaner outlet hose (2).
Inspection
Immerse temperature sensing part of IAT sensor in water (or ice)
and measure resistance between sensor terminals while heating
water gradually.
If measured resistance doesn’t show such characteristic as shown
in left figure, replace IAT sensor.
Installation
Reverse removal procedure noting the following.

Clean mating surfaces of IAT sensor and air cleaner outlet hose.

Connect IAT sensor coupler (1) securely.

2.297 – 2.595
0.298 – 0.320
6E2-30 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
ENGINE COOLANT TEMPERATURE SENSOR
(ECT SENSOR)
Removal
1) Disconnect battery negative cable at battery.
2) Drain coolant referring to Section 6B.
WARNING:
To help avoid danger of being burned, do not remove ra-
diator cap while engine and radiator are still hot.
Scalding fluid and steam can be blown out under pres-
sure if cap is taken off too soon.
3) Disconnect coupler from ECT sensor.
4) Remove ECT sensor (1) from thermostat case.
Inspection
Immerse temperature sensing part of ECT sensor (1) in water (or
ice) and measure resistance between terminal “A” and “B” while
heating water gradually.
If measured resistance doesn’t show such characteristic as shown
in left figure, replace ECT sensor (1).
Installation
Reverse removal procedure noting the following:

Clean mating surfaces of ECT sensor (1) and thermostat case.

Check O-ring for damage and replace if necessary.

Tighten ECT sensor (1) to specified torque.
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 9.0 lb-ft)

Connect coupler to ECT sensor (1) securely.

Refill coolant referring to Section 6B.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-31
1. Viewed from terminal side
Sensor-1
Sensor-2
“VB”
“GND”
HEATED OXYGEN SENSOR (Sensor-1 and Sensor-2)
Oxygen Sensor Heater Inspection
1) Disconnect sensor coupler.
2) Using ohmmeter, measure resistance between terminals “V
B”
and “GND” of sensor coupler.
NOTE :
Temperature of sensor affects resistance value largely.
Make sure that sensor heater is at correct temperature.
Resistance of oxygen sensor heater :
11.7 – 14.3 Ω at 20C, 68F
If found faulty, replace oxygen sensor.
3) Connect sensor coupler securely.
Removal
WARNING:
To avoid danger of being burned, do not touch exhaust sys-
tem when system is hot. Oxygen sensor removal should be
performed when system is cool.
1) Disconnect negative cable at battery.
2) For sensor-1, disconnect coupler of heated oxygen sensor and
release its wire harness from clamps and remove exhaust man-
ifold cover (1).
3) For sensor-2, disconnect coupler of heated oxygen sensor and
release its wire harness from clamp and hoist vehicle.
4) Remove heated oxygen sensor (2) from exhaust manifold or ex-
haust pipe.
Installation
Reverse removal procedure noting the following.

Tighten heated oxygen sensor (2) to specified torque.
Tightening Torque for heated oxygen sensor
(a): 45 N·m (4.5 kg-m, 32.5 lb-ft)

Connect coupler of heated oxygen sensor (2) and clamp wire har-
ness securely.

After installing heated oxygen sensor (2), start engine and check
that no exhaust gas leakage exists.

(a)
6E2-32 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
CAMSHAFT POSITION SENSOR
Inspection
Check camshaft position sensor referring to DTC P0340 Diag. Flow
Table in Section 6. If malfunction is found, replace.
Removal
1) Disconnect negative cable at battery.
2) Disconnect connector from camshaft position sensor.
3) Remove camshaft position sensor from sensor case
(distributorless ignition case).
Installation
1) Check that O-ring is free from damage.
2) Check that camshaft position sensor and signal rotor tooth are
free from any metal particles and damage.
3) Install camshaft position sensor to sensor case.
Tightening Torque
(a): 9 N
.m (0.9 kg-m, 6.5 lb-ft)
4) Connect connector to it securely.
5) Connect negative cable to battery.
CRANKSHAFT POSITION SENSOR
Inspection
Check crankshaft position sensor referring to step 1 and 2 of DTC
P0335 Flow Table. If malfunction is found, replace.
Removal
1) Hoist vehicle.
2) Disconnect connector from crankshaft position sensor.
3) Remove crankshaft position sensor from oil pan.
Installation
1) Check to make sure that crankshaft position sensor and pulley
tooth is free from any metal particles and damage.
2) Install crankshaft position sensor to oil pan.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
CAUTION:
Be sure to tighten to specified torque. CKP sensor will be
deformed if overtightened and correct CKP sensor signal
will not be fed if loosened.
3) Connect connector to it securely.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-33
VEHICLE SPEED SENSOR (VSS)
Inspection
Check vehicle speed sensor referring to step 3 of DTC P0500 Flow
Table. If malfunction is found, replace.
Removal / Installation
Refer to Section 7A.
FUEL LEVEL SENSOR (GAUGE)
Inspection
Refer to Section 8.
Removal / Installation
Refer to Section 6C.
MAIN RELAY, FUEL PUMP RELAY AND RADIATOR
FAN CONTROL RELAY
Inspection
1) Disconnect negative cable at battery.
2) Remove main relay (1), fuel pump relay (2) and radiator fan con-
trol relay (3) from relay box.
3) Check that there is no continuity between terminal “c” and “d”.
If there is continuity, replace relay.
4) Connect battery positive (+) terminal to terminal “b” of relay.
Connect battery negative (–) terminal “a” of relay.
Check continuity between terminal “c” and “d”.
If there is no continuity when relay is connected to the battery,
replace relay.

1
2
1. SUZUKI scan tool display
2. EGR valve opening (0: Close, 100: Full Open)
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-35
2) Connect battery (1) to radiator fan motor coupler (2) as shown
in figure, then check that the radiator fan motor operates
smoothly.
If radiator fan motor does not operate smoothly, replace motor.
EMISSION CONTROL SYSTEM
EGR SYSTEM
System Inspection (using SUZUKI scan tool)
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and then select “DATA LIST” mode on
scan tool.
3) Make sure that vehicle condition is as following.

Vehicle speed = 0 KPH

Engine coolant temp.
80C

Engine speed  3000 rpm
4) Clear DTC by using “CLEAR INFO” mode.
5) With engine idling (without depressing accelerator pedal), open
EGR valve by using “STEP EGR” mode in “MISC TEST” menu.
In this state, according as EGR valve opening increases engine
idle speed drops. If not, possible cause is clogged EGR gas pas-
sage, stuck or faulty EGR valve, poor performance of ECT sen-
sor or TP sensor or DTC and / or pending DTC is (are) stored in
ECM memory.
Removal
1) Disconnect negative cable at battery.
2) Disconnect EGR valve coupler.
3) Remove EGR valve and gasket from intake manifold.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-37
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose and check
that vacuum is not felt there when engine is cool and running at
idle speed.
3) Connect purge hose to EVAP canister and warm up engine to
normal operating temperature.
4) Disconnect purge hose from EVAP canister.
5) Also check that vacuum is felt when engine is running at idle
speed.
NOTE:
The EVAP canister purge system does not perform purging
(vacuum is not detected at the purge hose) unless the en-
gine is sufficiently warmed up and the heated oxygen sen-
sor is activated fully. Also, when the purge hose is discon-
nected in Step 4), the air is drawn into the purge line. As a
result, ECM (PCM) detects a change in the purge gas con-
centration and sometimes stops purging but this indicates
nothing abnormal.
If check result is not satisfactory, check vacuum passage, hoses,
EVAP canister purge valve, wire harness and ECM (PCM).
Vacuum Passage Inspection
Start engine and run it at idle speed. Disconnect vacuum hose (1)
from EVAP canister purge valve (2). With finger placed against
hose disconnected, check that vacuum is applied.
If it is not applied, clean vacuum passage by blowing compressed
air.
Vacuum Hose Inspection
Check hoses for connection, leakage, clog and deterioration. Re-
place as necessary.
EVAP Canister Purge Valve Inspection
Check EVAP canister purge valve referring to step 1 of DTC P0443
Flow Table.
If found malfunction, replace.