2000 SUZUKI GRAND VITARA Oil seal

YH4
GRAND
VITARA
1
1. Contact coil and combination switch assembly
2. Screw
1. Contact coil and combination switch assembly
1. Seal (if equipped, remove lock pin after installing
contact coil and combination switch assembly.)
2. Lock pin (if equipped, remove lock pin after installing
contact coil and combination switch assembly.)
3C1-8 AIR BAG STEERING WHEEL AND COLUMN
6) Remove contact coil and combination switch assembly from
steering column.
INSPECTION
Check contact coil and combination switch wire harness for any
signs of scorching, melting or other damage. If it is damaged, re-
place.
INSTALLATION
1) Check to make sure that vehicle's front tires are set at straight-
ahead position and then ignition switch is at ªLOCKº position.
2) Install contact coil and combination switch assembly to steering
column.
NOTE:
New contact coil and combination switch assembly is sup-
plied with contact coil set and held at its center position
with a lock pin and seal. Remove this lock pin after installing
contact coil and combination switch assembly to steering
column.

YH4
GRAND
VITARA
3D-10 FRONT SUSPENSION
ªaº < ªbº
1. Circlip
2. Large diameter
1. Axle shaft drive flange
2. Bolt 1. Spring seat
Bottom
INSTALLATION
Reverse removal procedure to install coil spring.
NOTE:
Upper and lower diameters of coil spring are different.
Bring larger diameter end at bottom and set its open end in
place on spring seat.

Be sure to use specified torque for tightening each fastener.

Refer to torque specification chart at the end of this section.

As for ball stud nut, be sure to insert split pin and bend it after tight-
ening it.

Tighten tie-rod end nut with pushing ball stud to upper side so as
not ball stud to be rotated.

For 4WD vehicle
Apply lithium grease to front drive shaft washer and front wheel
spindle outer.
ªAº: Grease 99000-25010

For 4WD vehicle
When installing circlip to drive shaft, utilize screw hole in drive
shaft to pull it out and bring large diameter of circlip at right as
shown.

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange and tighten flange bolt
to specified torque.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
1. Drive shaft
circlip
2. Spindle thrust
washer
3. Drive shaft
4. Wheel spindle
1. Tie-rod end
2. Knuckle
1. Strut
2. Knuckle
1. Dust cover
2. Wheel spindle
3. Knuckle
4. Inner oil seal /
knuckle cap
FRONT SUSPENSION 3D-17
KNUCKLE / WHEEL SPINDLE
REMOVAL
1) Remove wheel hub. Refer to ªWHEEL HUB (INCLUDED
WHEEL BEARING)º in this section.
2) Remove front drive shaft circlip and front spindle thrust washer
(for 4WD vehicle) or front hub cap (for 2WD vehicle).
3) Disconnect tie-rod end from knuckle.
4) Remove stabilizer bar. Refer to ªSTABILIZER BAR / BUSH-
INGSº in this section.
5) Remove ball stud nut.
6) Support lower arm with jack.
7) Remove strut bracket bolts from strut bracket.
8) By using puller, disconnect knuckle from ball stud.
9) While lowering jack, remove knuckle / wheel spindle comp.
10) Remove inner oil seal (for 4WD vehicle), knuckle cap (for 2WD
vehicle), dust cover and wheel spindle.

YH4
GRAND
VITARA
ªAº
ªBº
1. Wheel spindle
2. Drive shaft bearing
1. Wheel spindle
2. Drive shaft
bearing
3. Front drive shaft
thrust washer
4. Inner oil seal
5. Knuckle cap
6. Drive shaft oil sealType A Type B
1. Drive shaft bearing
2. Wheel spindle
3D-18 FRONT SUSPENSION
11) For 4WD vehicle
Remove drive shaft bearing by using special tool.
Special Tool
(A): 09923-74510
(B): 09930-30102
INSTALLATION
Reverse removal sequence to install knuckle, wheel spindle oil seal
and drive shaft bearing,noting following points.

For 4WD vehicle
Install drive shaft bearing by using special tool.
Special Tool
(A): 09913-76010 Type A drive shaft thrust washer. . . . . . . .
(A): 09913-80112 Type B drive shaft thrust washer. . . . . . . .
Dimension ªaº: 0 ± 1 mm (0 ± 0.04 in.)
Dimension ªaº: Type A drive shaft thrust washer . . . . . . . . .
Dimension ªaº: 1.75 ± 2.50 mm (0.069 ± 0.098 in.)
Dimension ªaº: Type B drive shaft thrust washer . . . . . . . . .

When installing wheel spindle to knuckle, coat their mating sur-
faces with sealant.
ªAº: Sealant 99000-31110

For 4WD vehicle
Also, fill recess in wheel spindle with about 10 g lithium grease.
ªBº: Grease 99000-25010

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-19
1. Knuckle
2. Knuckle cap
3. Wheel spindle 1. Oil seal
2. Drive shaft
3. Drive shaft
thrust washer
Type A Type B

Tighten wheel spindle nut to specified torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For 4WD vehicle
Press-fitting inner oil seal.
Drive in inner oil seal until its end contacts stepped surface of
knuckle by using special tools.
Special Tool
(B): 09944-66010
(C): 09924-74510

For 4WD vehicle

Apply lithium grease to oil seal lip and into its hollow to fill more
than 60% of its vacant space.

Apply lithium grease ªAº to drive shaft.
ªAº: Grease 99000-25010

Press-fit front drive shaft thrust washer to drive shaft, if it is re-
moved (for Type B drive shaft thrust washer). Apply lithium
grease ªAº to drive shaft thrust washer.
ªAº: Grease 99000-25010

Apply lithium grease ªAº and install front drive shaft thrust wash-
er with its chamfered side facing to center side (for Type A drive
shaft thrust washer).
ªAº: Grease 99000-25010

For 2WD vehicle
Remove grease, old sealant and dusts from mating surfaces of
knuckle cap and knuckle to clean, apply water tight sealant to cap
mating surface evenly, and install cap to knuckle.
ªBº: Sealant 99000-31090

YH4
GRAND
VITARA
3D-24 FRONT SUSPENSION
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSENO.
Lithium greaseSUZUKI SUPER GREASE (A)
(99000-25010)
Bearing inner oil seal / drive shaft oil seal
Recess of wheel spindles
Spindle outer washer
Spindle part of drive shaft
Spindle bush (inside and flange part)
Spindle inner washera
b
c
d
e
f
SealantSUZUKI BOND NO. 1215
(99000-31110)Mating surfaces of wheel spindle
and knuckle1
Sealing compound
SUZUKI SEALING COM-
POUND 366E
(99000-31090)
Front axle cap
Mating surfaces of wheel hub and drive
flange
Knuckle cap
Hub capA
B
C
D

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-25
09923-74510
Bearing remover09930-30102
Sliding shaft09924-74510
Bearing installer handle09941-66010
Bump stopper wrench
09942-15510
Sliding hammer09943-35512
Brake drum remover09944-68210
Bearing & oil seal installer 09944-66010
Wheel hub / knuckle oil
seal installer
09951-16050
Wheel bearing tightening tool09951-46020
Control arm remover support 09951-16060
Control arm bush remover
(front)09913-80112
Bearing installer
09925-58210
Oil seal installer09913-85210
Oil seal installer
09952-86510
Front sensor rotor installer
SPECIAL TOOLS

YH4
GRAND
VITARA
3E
REAR SUSPENSION 3E-1
GENERAL DESCRIPTION3E- 2 . . . . . . . . . . . . . .
DIAGNOSIS3E- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3E- 3. . . . . . . . . . . . . . . . . . . . . .
Shock Absorber Check 3E- 3. . . . . . . . . . . . . . . .
Lower / Upper / Lateral Rod Check 3E- 3. . . . . . . .
Axle Housing and Coil Spring Check 3E- 3. . . .
Bearing Retainer & Axle Shaft Inner Oil
Seal Check 3E- 4. . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Disc, Nut & Bearing Check 3E- 4. . . . . .
ON-VEHICLE SERVICE3E- 5 . . . . . . . . . . . . . . . .
Shock Absorber 3E- 5. . . . . . . . . . . . . . . . . . . . . . Coil Spring 3E- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Rod 3E- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Rod 3E- 9. . . . . . . . . . . . . . . . . . . . . . . . . .
Lateral Rod 3E-10. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Axle Shaft and Wheel Bearing 3E-10. . . . .
Rear Axle Shaft Inner Oil Seal 3E-15. . . . . . . . . .
Rear Axle Housing 3E-16. . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3E-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3E-23 . . . . . .
SPECIAL TOOLS3E-24 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3E
REAR SUSPENSION
NOTE:

All suspension fasteners are an important attaching part in that it could affect the performance of vital
parts and systems, and / or could result in major repair expense. They must be replaced with one of the
same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality or substitute design. Torque values must be used as specified during reas-
sembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any suspension part. Replace it with a new part, or damage
to the part may result.
CONTENTS