2000 SUZUKI GRAND VITARA Oil seal

YH4
GRAND
VITARA
Viscosity chart
SAE
1. Reverse idle gear shaft bolt
(DO NOT LOOSEN IT)
MANUAL TRANSMISSION (TYPE 1) 7A-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:

It is highly recommended to use SAE 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.

If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 1.5 liters (3.2 / 2.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to its thread.
CAUTION:

Transmission oil must not be poured through gear shift
control lever part.

Do not loosen or remove reverse idle gear shaft bolt.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 1) 7A-13
1
1. Extension case
2. Select return spring bolt
3. Select return spring (short)
4. Select return spring (long)
5. Guide pin
6. Speed sensor assembly 62,ªAº,(a)
3,ªAº
5,ªAº
5,ªAº
4,ªAº
2,ªAº,(a)
1. Oil seal
2. Extension case
ªBºªAº
1
1
22
EXTENSION CASE (2WD MODEL)
DISASSEMBLY
1) Remove oil seal.
2) Remove select return spring bolts and then springs and guide
pins.
3) Remove speed sensor assembly.
REASSEMBLY
1) Install oil seal.
2) After applying grease, install select guide pins, select return
springs and spring bolts and torque them to specification.
ªAº: Grease 99000-25010
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
After installing, check to make sure that each pin moves smooth-
ly.
3) Install speedometer driven gear case assembly to extension
case.
EXTENSION CASE OIL SEAL (2WD MODEL)
REMOVAL AND INSTALLATION
1) Remove propeller shaft referring to SECTION 4B.
2) Using screwdriver, remove oil seal.
3) Using special tool (A) and plastic hammer, press fit new oil seal
into extension case till oil seal contacts stepped part of extension
case as shown. Be sure to apply grease to oil seal lip.
ªAº: Grease 99000-25010
Special Tool
(A): 09951-16060
4) Clean and inspect sliding portion of propeller shaft front end
(where oil seal contacts) before installation and if even small
dent or scratch exists, correct and clean it again.
Then apply grease inside splines of propeller shaft.
ªBº: Grease 99000-25010
5) Install propeller shaft referring to SECTION 4B.

YH4
GRAND
VITARA
7A-14 MANUAL TRANSMISSION (TYPE 1)
09951-16060
Oil seal installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back up light switch (Type 1)202.014.5
Back up light switch (Type 2)454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts and nut505.036.5
Exhaust center pipe to manifold nuts505.036.5
Muffler to exhaust center pipe bolts505.036.5
Universal joint flange bolts505.036.5
Select return spring bolts232.317.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever.

Select return springs, bolts and guides.
Thread lock cementTHREAD LOCK CEMENT
SUPER 1333B (99000-32020)
Shift control lever locating bolts.
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil Drain and filler / level plugs.
SPECIAL TOOL

YH4
GRAND
VITARA
7A1
MANUAL TRANSMISSION (TYPE 2) 7A1-1
TYPE 2
GENERAL DESCRIPTION7A1-1 . . . . . . . . . . . . . .
DIAGNOSIS7A1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A1-3 . . . . . . . . . . . . . . . .
Gear Oil 7A1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A1-4. . . . . . . . . . . . . . . . . . .
Switches 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A1-4. . . . . . . . . . . . . . . . Dismounting / Remounting of
Trans. Unit 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A1-4 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A1-5 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A1-5 . . . . . .
The manual transmission consists of the input shaft,
main shaft, counter shaft and reverse gear which are
installed in the aluminum and castings cases. Its
gears are of forward five speeds in synchro mesh and
reverse one speed in sliding idler gear arrangement
system.
The main shaft gears are held by the needle bear-
ings and on them the synchronizer rings and syn-
chronizer sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.As the aluminum and castings cases are sealed with
liquid type gasket, it is necessary to use genuine seal-
ant or its equivalent on its mating surfaces when reas-
sembling them. Also, the case fastening bolts must be
tightened to specified torque by means of the torque
wrench and tightening over or below the specified
torque should be avoided.
The description under ON-VEHICLE SERVICE in this
section covers the transfer partially which is next to
the transmission as well, but their gear boxes are in-
dependent and each of them has its own drain and
level / filler plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A1
MANUAL TRANSMISSION
(TYPE 2)
CONTENTS
GENERAL DESCRIPTION

YH4
GRAND
VITARA
Viscosity chart
SAE
Temperature
1. Drain plug
2. Oil level / filler plug
MANUAL TRANSMISSION (TYPE 2) 7A1-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:

It is highly recommended to use SAE 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.

If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 2.6 liters (5.5 / 4.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to thread of plug (c).
CAUTION:
Transmission oil must not be poured through gear shift
control lever part.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 38 N´m (3.8 kg-m, 27.5 lb-ft)
(b): 23 N´m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 2) 7A1-5
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN´mkg-mlb-ft
Transfer oil filler / level and drain plugs232.317.0
Transmission oil filler / level and drain plugs383.827.5
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back-up light switch454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts505.036.5
Muffler to exhaust No. 2 pipe nuts505.036.5
Universal joint flange bolts505.036.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever
Thread lock cement
THREAD LOCK CEMENT
SUPER 1333B
(99000-32020)

Shift control lever locating bolts
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil drain and filler / level plugs

YH4
GRAND
VITARA
7B1-30 AUTOMATIC TRANSMISSION (4 A / T)
Running condition Gear shift Abnormal
noise
ConditionPossible CauseCorrection
Poor 1st speed run-
ning or excessive
slippage in ªDº or ª2º
Fluid pressure leakage from forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Overdrive clutch slippingReplace.
Unable to run or ex-
cessive slippage in
ªLº range
Fluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Reverse brake disc slippingReplace.

Broken brake piston O-ringReplace.
Unable to run or ex-
cessive slippage in
ªRº range
Fluid pressure leakage to direct clutch due
to wear or breakage of center support seal
ringReplace.

Worn direct clutchReplace.
Poor 1±2 shift, ex-
cessive slippage
Fluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.

Faulty second brakeReplace.

Broken O-ring of second brake pistonReplace.

Faulty second coast brake (in ª2º range)Replace.
Poor 2±3 shift, ex-
cessive slippage
Fluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.

Worn direct clutch bushingReplace.

Direct clutch slippingReplace.

Foreign material caught in direct clutch pis-
ton check ballReplace.
Poor start or surging
in ªDº range
Fluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.

Malfunction of forward clutchReplace.
Poor 3±4 shift, ex-
ili

Faulty overdrive brakeReplace.
cessive slippage
Faulty overdrive clutchReplace.
Poor start or judder-
ing in ªRº range
Fluid pressure leakage of direct clutch due
to wear or breakage of oil center support
seal ringReplace.

Worn direct clutchReplace.
Excessive shock on
1± 2 shift
Faulty one-way clutchReplace.
Non operate lock-up
system
Faulty torque converterReplace.
Abnormal noise in
ªPº or ªNº range
Worn oil pumpReplace.
SCAN TOOL DATA-Refer to SECTION 6 / 6-1.
INSPECTION OF PCM AND ITS CIRCUIT-Refer to SECTION 6 / 6-1.
WIRE HARNESS AND CONNECTORS-Refer to SECTION 6 / 6-1.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-77
ªAº, (d)
1. Drive plate
2. Torque converter
3. Case right stiffener (if equipped)
4. Automatic transmissionTightening torque
(a): 50 N´m
5.0 kg-m
36.5 lb-ft
(b): 65 N´m
6.5 kg-m
47.0 lb-ft
(c): 85 N´m
8.5 kg-m
61.5 lb-ft
(d): 78 N´m
7.8 kg-m
56.5 lb-ft
1. Automatic transmission
2. Transfer (4WD)
3. Engine rear mounting
4. Engine rear mounting member Tightening torque
(a): 50 N´m (5.0 kg-m, 36.5 lb-ft) ªAº: Sealant 99000-31110
REMOUNTING
WARNING:
When moving transmission assembly with torque convert-
er equipped in it, be sure to keep it horizontal. Tilting it with
its front facing down may allow converter to fall off. Where-
by an injury may result.
For remounting, reverse dismounting procedure. Use specified
torque as given below and left.
Tightening torque
N.mkg-mlb-ft
Exhaust No.1 pipe to manifold
bolts or nuts505.036.5
Muffler to exhaust No.2 pipe
nuts606.043.5
Universal joint flange bolts and
nuts505.036.5

Oil filler tube bolts

Select cable bracket bolts232.317.0

Clamp wiring harness and hoses securely.

Refer to ªSelect Cableº section for adjusting procedure of select
cable.

Refer to ªA / T Throttle Cableº section for tuning of A / T throttle
cable.

Follow fluid level check procedure for refilling automatic transmis-
sion fluid and its level adjusting.

Connect battery, and confirm that engine and transmission func-
tion acceptably.

When remounting drive plate, use specified bolts.