2000 SUZUKI GRAND VITARA Oil seal

YH4
GRAND
VITARA
1. Rear axle housing
2. Coil spring
3. Axle shaft
4. Shock absorber
5. Upper rod
6. Lower rod
7. Oil level plug
8. Wheel bearing retainer
9. Rear wheel bearing
10. Brake back plate
11. Oil drain plug
12. Lateral rod
NOTE:
When installing differential gear oil drain
plug, clean the thread portion of the plug and
then apply sealant (SUZUKI BOND No. 1215,
99000-31110) to the portion.
8
3E-2 REAR SUSPENSION
GENERAL DESCRIPTION
Rear suspension is 5 link type of rigid axle which consists of coil springs, rear axle, shock absorbers, upper rods,
lower rods and lateral rod.
The lower rod and upper rod are connected with the axle and body by using bushes so that axle moves up and
down with bushes as their supporting points.
The shock absorber is installed between the body and axle to absorb up-and-down movement of the vehicle body.

YH4
GRAND
VITARA
ªAº: Drill hole with approximately
3 mm (0.12 in.) diameter.
REAR SUSPENSION 3E-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to SECTION 3.
SHOCK ABSORBER CHECK

Inspect for deformation or damage.

Inspect bushings for wear or damage.

Inspect for evidence of oil leakage.
Replace any defective part.
WARNING:
When handling rear shock absorber in which high-pressure
gas is sealed, make sure to observe the following precau-
tions.
1) Don't disassemble it.
2) Don't put it into the fire.
3) Don't store it where it gets hot.
4) Before disposing it, be sure to drill a hole in it where
shown by an arrow in the figure and let gas and oil out.
Lay it down sideways for this work.
5) The gas itself is harmless but it may issue out of the hole
together with chips generated by the drill. Therefore, be
sure to wear goggle.
LOWER ROD, UPPER ROD, LATERAL ROD
CHECK
Inspect for cracks, deformation or damage.
Replace any defective part.
Inspect each bush for wear and breakage. If found defective, re-
place.
AXLE HOUSING AND COIL SPRING CHECK
Inspect for cracks, deformation or damage.
Inspect for evidence of oil leakage at axle housing.
If any, replace defective part.

YH4
GRAND
VITARA
3E-4 REAR SUSPENSION
REAR SUSPENSION FASTENERS
Check each bolt and nut fastening suspension parts for tightness.
Tighten loose one, if any, to specified torque, referring to ªTIGHT-
ENING TORQUE SPECIFICATIONSº of this section.
BEARING RETAINER AND AXLE SHAFT
INNER OIL SEAL CHECK

When brake drum has been removed, check inside of brake drum
for gear oil leakage.

Also, check backside of brake back plate for oil leakage.
If oil leakage is found, replace defective oil seal.

Whenever it is possible to check oil seal during disassembly,
check its lip for wear.
If oil leakage or worn lip is found, replace defective oil seal.
WHEEL DISC, NUT & BEARING CHECK

Inspect each wheel disc for dents, distortion and cracks. A disc
in badly damaged condition must be replaced.

Check wheel hub nuts for tightness and retighten to specification
as necessary.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)

Check wheel bearings for wear. When measuring thrust play, ap-
ply a dial gauge to axle shaft center after removing wheel center
cap from wheel.
Thrust play limit
Rear0.8 mm (0.03 in.)
When measurement exceeds limit, replace bearing.

By rotating wheel actually, check wheel bearing for noise and
smooth rotation. If it is defective, replace bearing.

YH4
GRAND
VITARA
[B]
1
2
[A]
1. Bearing retainer
2. Oil seal
3. Wheel side
4. Differential side
1. Stud bolt
2. Nut
3. Washer
4. Flange of axle shaft
1. Axle shaft
2. Bearing retainer
[A]: Vehicle without ABS
[B]: Vehicle with ABS
1. Bearing
2. Retainer ring
REAR SUSPENSION 3E-13
INSTALLATION
Install removed parts in reverse order of removal procedure, noting
the following.
1) Apply grease to oil seal lip as shown and install it to axle shaft.
NOTE:
Amount of grease applied to hollow in oil seal should be
more than 60% of its vacant space.
ªAº: Grease 99000-25010
2) Aligning serrations between new stud bolt(s) and flange, install
new stud bolt(s) by tightening nut as shown.
3) Install bearing retainer to shaft.
4) Press-fit wheel bearing and retainer ring as shown.
NOTE:

Use care not to cause any damage to outside of retainer
ring.

Refer to figure so that wheel bearing is installed in proper
direction.

YH4
GRAND
VITARA
1. Sensor rotor
1. Axle housing
1. Bearing retainer
(b)
3E-14 REAR SUSPENSION
5) For vehicle with ABS, press-fit new sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
6) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010
7) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
8) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
9) Tighten wheel speed sensor bolt to specified torque (if
equipped with ABS).
Tightening Torque
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
10) Refill rear axle (differential) housing with new specified gear oil.
Refer to SECTION 7F for refill.
11) Install brake drum. (For details, refer to BRAKE DRUM
INSTALLATION in SECTION 5.)

YH4
GRAND
VITARA
REAR SUSPENSION 3E-15
1. Inner oil seal
2. Axle housing
1. Hammer
2. Screwdriver
3. Oil seal protector
4. Oil seal
5. Body center
REAR AXLE SHAFT INNER OIL SEAL
REMOVAL
1) Remove rear axle shaft. For details, refer to steps 1) to 7) of
REAR AXLE SHAFT REMOVAL in this section.
2) Fix brake back plate by inserting screwdriver to the hole for bear-
ing retainer mounting.
3) Remove rear axle shaft inner oil seal.
NOTE:
Take care not to bend the brake pipe.
INSTALLATION
1) Using special tool drive in oil seal until it contacts oil seal protec-
tor in axle housing.
NOTE:

Make sure that oil seal is free from inclination as it is
installed.

Refer to figure so that oil seal is installed in proper direc-
tion.
Special Tool
(A): 09913-75510
ªAº: Grease 99000-25010
ªBº: Sealant 99000-31110
2) For procedure hereafter, refer to steps 6) to 11) of REAR AXLE
SHAFT INSTALLATION in this section.

YH4
GRAND
VITARA
1. Lower rod
2. Body center
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Axle housing ªAº 1. Body center
1
2
1
REAR SUSPENSION 3E-19
INSTALLATION
Install removed parts in reverse order of removal, noting the follow-
ing.
1) Place rear axle housing on floor jack. Then install upper / lower
rod rear mounting bolts (right & left) in proper direction as shown
(refer to UPPER ROD INSTALLATION for upper rod bolts). At
this time, mount nuts but don't tighten them.
2) Install coil spring (right & left) on spring seat of axle housing and
raise axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
3) Install lateral rod to rear axle housing.
4) Install lower part of shock absorber to right and left sides of axle
housing and install bolts in proper direction as shown in figure.
At this time, mount nuts but don't tighten them.
5) Clean mating surfaces of axle housing and differential carrier
and apply sealant to housing side.
ªAº: Sealant 99000-31110
6) Install differential carrier assembly to axle housing and tighten
carrier nuts to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)

YH4
GRAND
VITARA
1. Axle housingªAº
(c)
1. Axle housing
3E-20 REAR SUSPENSION
7) For vehicle with ABS, connect wheel speed sensor coupler and
install harness.
8) Install propeller shaft and torque nuts to specification.
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
9) Remove floor jack from axle housing and connect breather
hose onto axle housing and clamp it securely.
10) Connect brake pipes onto axle housing and clamp them se-
curely.
For clamping positions, refer to SECTION 5A of this manual.
11) Connect brake flexible hose to bracket on axle housing and se-
cure it with E-ring.
12) Install LSPV stay to axle housing, tighten LSPV stay bolt to
specified torque.
And adjust LSPV referring to ªLSPV ASSEMBLY INSPEC-
TION AND ADJUSTMENTº in SECTION 5A.
Tightening Torque
(c): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
13) Connect brake pipe to brake flexible hose and tighten brake
pipe flare nut to specified torque.
Tightening Torque
(d): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
14) Clean mating surface of axle housing (right & left) and brake
back plate, then apply sealant as shown.
ªAº: Sealant 99000-31110
15) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010