2000 SUZUKI GRAND VITARA headlight

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-35
FORWARD
1. Front wheel speed
sensor connector
2. Headlight assembly
1. Front wheel speed sensor
2. Bolt
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle and remove wheel.
3) Disconnect front wheel speed sensor connector.
4) Remove harness clamp bolts and remove front wheel speed
sensor from knuckle.
CAUTION:

Do not pull wire harness when removing front wheel
speed sensor.

Do not cause damage to surface of front wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.
SENSOR INSPECTION

Check sensor for damage.

Check sensor for resistance.
Resistance between terminals: 1.2 ± 1.6 k
at 20C (68F)
Resistance between terminal and sensor body: 1 M
or more
If any faulty is found, replace.
SENSOR ROTOR INSPECTION

Check rotor for being missing, damaged or deformed.

Turn drive shaft and check if rotor rotation is free from eccentricity
and looseness.

Check that no foreign material is attached.
If any faulty is found, repair or replace. Refer to WHEEL HUB RE-
MOVAL and INSTALLATION in Section 3D.

YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
6
5
1. Headlight assembly
2. Halogen bulb
3. Socket cover
4. Turn signal light bulb
5. Position light bulb
6. Turn signal light bulb socket
7. Position light bulb socket
8B-2 LIGHTING SYSTEM
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
HEADLIGHTS

YH4
GRAND
VITARA
1. Headlight leveling switch
2. Headlight leveling unit (actuator)
3. Headlight
4. Headlight leveling unit shaft
Switch
PositionHeadlight beam
down angle
0 ÐÐÐ
1 0.624

2 1.243

3 1.867

4 2.479

LIGHTING SYSTEM 8B-3
HEADLIGHT WITH LEVELING SYSTEM (IF EQUIPPED)

YH4
GRAND
VITARA
8B-4 LIGHTING SYSTEM
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
HEADLIGHTS
TroublePossible causeCorrection
Only one light does not
light
Bulb blown

Headlight L or R fuse blown

Socket, wiring or grounding faultyReplace bulb
Replace fuse to check for short
Repair
Headlights do not light
Headlight L and R fuses blown

Lighting and dimmer switch faulty

Defective light relay

Wiring or grounding faultyReplace fuses to check for short
Replace switches
Replace light relay
Repair
Only one beam (ªHiº or
ªLoº) does not light
Bulb blown

Lighting or dimmer switch faultyReplace bulb
Replace switch
HEADLIGHTS WITH LEVELING SYSTEM (IF EQUIPPED)
TroublePossible causeCorrection
Both headlights do not
move
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Leveling switch faulty

Supply voltage too lowReplace fuse to check for short
Replace switch
Recharge or replace battery
One of headlights (either
Right or Left) does not
move
Socket, wiring or grounding faulty

Actuator faulty

Vehicle body around headlight deformed

Headlight ass'y itself deformedRepair
Replace actuator
Repair body
Replace headlight ass'y
TURN SIGNAL AND HAZARD WARNING LIGHTS
TroublePossible causeCorrection
Flash rate high or one side
only flashes
Incorrect bulb

One of light bulbs burnt out

Turn signal / hazard warning relay faulty

Open circuit or high resistance existing
Replace bulb
Replace
Replace relay
Repair
Oen circuit or high resistance existing
between turn signal / hazard warning
switch and lights on one side

Wiring or grounding faulty
Re air
Repair
No flashing
ªTURN / BACKº and / or ªHAZARDº fuse(s)
blown (Hard Top Model)
ªTRNº and / or ªHAZº fuse(s) blown
(Canvas Top Model)

Open circuit or high resistance existing
between battery and switch

Turn signal / hazard relay faulty

Combination switch or hazard switch faulty

Wiring or grounding faultyReplace fuse(s) to check for
short
Check bulb and check circuit
Replace relay
Replace switch
Repair
Flash rate low
Supply voltage too low

Turn signal / hazard relay faultyCheck charging system
Replace relay

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.

YH4
GRAND
VITARA
8B-8 LIGHTING SYSTEM
HEADLIGHTS WITH LEVELING SYSTEM
(IF EQUIPPED)
LEVELING SWITCH
INSPECTION
To check the switch operation, substitute it with a new one. If proper
operation is obtained, it means the switch is defective.
Replace it with a new one.
LEVELING ACTUATOR
INSPECTION
All headlight system couples connected including leveling actuator
and switch, and at Ignition switch ON, listen to the leveling actuator
sound on both actuators according to the movement of the leveling
switch. If no sound is heard with the movement of the leveling
switch, replace headlight assembly.