2000 SUZUKI GRAND VITARA Crankshaft plate

YH4
GRAND
VITARA
1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control valve Assembly
3B1-4 POWER STEERING (P / S) SYSTEM
POWER STEERING (P / S) PUMP
The power steering pump is a vane type and is driven by the V-ribbed belt from the crankshaft.
ModelVane type
Hydraulic
pressure
controlRelieved
pressure
6500 kPa (65 kg / cm2, 924 psi)
G16 Type engine . . . . . . . . . . . . . . . . . . . . . .
7000 kPa (70 kg / cm
2, 995 psi)
J20 Type engine . . . . . . . . . . . . . . . . . . . . . . .
7350 kPa (73.5 kg / cm
2, 1045 psi)
H25 Type engine . . . . . . . . . . . . . . . . . . . . . .
ControlFlow control valve
deviceRelief valve
Power steering
pressure switch
Switch turns on (closes) when the
pressure is higher than 2500 ± 3500 kPa
(25 ± 35 kg / cm
2, 356 ± 498 psi).
ECM uses this signal for idle speed control.
Capacity0.70 ± 0.75

(1.48 / 1.23 ± 1.58 / 1.32 US / Imp. pt)
Specified fluidDEXRON
II, DEXRON
III A / T fluid
or equivalent
FLOW CONTROL VALVE
As the discharge rate of the P/S pump increases in proportion to the
pump revolution speed, a flow control valve is added to control it so
that the optimum amount of fluid for steering operation is supplied
according to the engine speed (driving condition).
Described below is its operation at different engine speed.

YH4
GRAND
VITARA
1. Crankshaft
2. Flywheel
3. Clutch disc
4. Pressure plate
5. Clutch cover
6. Diaphragm spring
7. Release bearing
8. Input shaft bearing
9. Input shaft
10. Operating cylinder
11. Clutch housing
12. Release fork
7C1-2 CLUTCH
The clutch is a diaphragm-spring clutch of a dry single
disc type. The diaphragm spring is of a tapering-finger
type, which is a solid ring in the outer diameter part,
with a series of tapered fingers pointing inward.
The disc, carrying torsional coil springs, is positioned
on the transmission input shaft with an involute spline
fit.
The clutch cover is secured to the flywheel, and car-
ries the diaphragm spring in such a way that the pe-
ripheral edge part of the spring pushes on the pres-
sure plate against the flywheel (with the disc in be-
tween), when the clutch release bearing is held back.
This is the engaged condition of the clutch.Depressing the clutch pedal causes the release bear-
ing to advance and pushes on the tips of the tapered
fingers of the diaphragm spring. When this happens,
the diaphragm spring pulls the pressure plate away
from the flywheel, thereby interrupting the flow of
drive from flywheel through clutch disc to transmis-
sion input shaft.
GENERAL DESCRIPTION

YH4
GRAND
VITARA
7C1-12 CLUTCH
(C)
1
ªAº, (a)1
2
1. Flywheel
2. Bolt
1. Clutch cover
INSTALLATION
NOTE:
Before assembling, make sure that flywheel surface and pres-
sure plate surface have been cleaned and dried thoroughly.
1) Install flywheel to crankshaft and tighten bolts to which sealant
is applied to specification.
Special Tool
(A): 09924-17810
ªAº: Sealant 99000-31110
Tightening Torque
(a): 78 N
.m (7.8 kg-m, 56.5 lb-ft) (G16 engine)
(a): 70 N
.m (7.0 kg-m, 50.5 lb-ft) (J20 and H25 engines)
2) Using special tool (B), install input shaft bearing to flywheel.
Special Tool
(B): 09925-98210
3) Aligning clutch disc to flywheel center by using special tool (C),
install clutch cover and bolts. Then tighten bolts to specification.
NOTE:

While tightening clutch cover bolts, compress clutch disc
with special tool (C) by hand so that disc centered.

Tighten cover bolts little by little evenly in diagonal order.
Special Tools
(A): 09924-17810
(C): 09923-36330 (G16 engine)
(C): 09923-36320 (J20 and H25 engines)
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 16.5 lb-ft)