2000 SUBARU IMPREZA Owners Manual

Maintenance and service10-41
–
CONTINUED –
solid b and ac ross the tread . The ind ic ators ap p ear
when the remaining
tread has b een worn to 0.063 in (1.6 mm) or less.
Wheel covers (Locking type wheel covers)
n Removing the wheel cover
CAUTION
If it becomes necessary to remove the wheel cover, NEVER use a screwdriver or other prying tool. Doing so will severely damage
or destroy the wheel cover.
HG0105
Grasp the wheel c over with b oth hand s b y the sp okes and twist
sharp ly in a counterclockwise d irec tion until you feel the d etent
release. Now the wheel c over is free from the reten tion ring .
n Installing the wheel cover
1. Install the wheel c over on the retention ring , al ig ning the valve stem
with the valve stem area and fitting the loc k p ins on the wheel c over
with the loc k sp ring s in the retention ring .

10-42
HG0124
Lock pin
2. Grasp the wheel c over with b oth hand s b y the sp ok es and twist
sharp ly in a clockwise d irec tion until you feel the d etent loc king . After
twisting the wheel c over, make sure the wheel c over is loc ked
sec urely b y lig htly turning the wheel c over rig ht a nd left.
HG0126
NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheelnuts after driving approximately 600 miles (1,000 km). If any nut isloose, tighten it to the specified torque.

Maintenance and service10-43
–
CONTINUED –

Wheel covers (Regular type wheel covers)
n Removing the wheel cover
HGA012BA
Insert the wheel c over remover into the notc h p rovi d ed , and p ry the
wheel c over off. n Installing the wheel cover
HGA013BA
Alig n the valve with the valve hole in the c over, t hen fit the c over on
the wheel b y tap p ing your hand evenly around the c i rc umferenc e of
the c over. NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheelnuts after driving approximately 600 miles (1,000 km). If any nut isloose, tighten it to the specified torque.

10-44Aluminum wheels (if equipped)
Aluminum wheels c an b e sc ratc hed and d amag ed easily
. Hand le them
c arefully to maintain their ap p earanc e, p erformanc e , and safety.
When any of the wheels is removed and rep lac ed for tire rotation or to
c hang e a flat, always c hec k the tig htness of the wh eel nuts after d riving
ap p roximately 600 miles (1,000 km). If any nut is l oose, tig hten it to the
sp ec ified torq ue. Never ap p ly oil to the thread ed p arts, wheel nuts, or tap ered surfac e
of the wheel. Never let the wheel rub ag ainst sharp p rotrusions o r c urb s.
Be sure to fit tire c hains on uniformly and c omp let ely around the tire,
otherwise the c hains may sc ratc h the wheel. When wheel nuts, b alanc e weig hts, or the c enter c ap are rep lac ed ,
b e sure to rep lac e them with g enuine SUBARU p arts d esig ned for alumi-
num wheels. Fuses
HG0127
HS0202
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in
two fuse b oxes.
If any lig hts, ac c essories or other elec tric al c ont rols d o not op erate, in-
sp ec t the c orresp ond ing fuse. If a fuse has b lown, rep lac e it.

Maintenance and service10-45
–
CONTINUED –
HS0204
Good Blown
CAUTION
Never replace a fuse with one having a higher rating or with mate-
rial other than a fuse because serious damage or a fire could re-sult.
Fuse box (behind the coin tray)
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec -
tric al ac c essories.
HS0202
2. Op en the c oin tray and p ull it horizontally to re move it.
3. Determine whic h fuse may b e b lown. The b ac k sid e of the c oin
tray and the “Fuse and c irc uits ” sec tion in c hap ter 11 in this manual
show the c irc uit for eac h fuse.

10-46
HS0208
HS0207
Fuse puller Fuse puller
Spare fuses
4. Pull out the fuse with the fuse p uller. The fuse p uller is stored in the
main fuse b ox c over in the eng ine c omp artment.
5. Insp ec t the fuse. If it has b lown, rep lac e it wit h a sp are fuse of the
same rating . The sp are fuses are stored in the main fuse b ox c over in
the eng ine c omp artment.
6. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs. Main fuse box (in the engine compartment)
1. Turn the ig nition switc h to the “LOCK ” p osition and turn off all elec -
tric al ac c essories.
2. Op en the eng ine hood .
3. Remove the main fuse b ox c over.
4. Determine whic h fuse may b e b lown. The fuse b ox c over and
“ Fuse and c irc uits ” sec tion in c hap ter 11 in this manual show the c ir-
c uit for eac h fuse.

Maintenance and service10-47
–
CONTINUED –
HS0208
HS0207
Fuse puller Fuse puller
Spare fuses
5. Pull out the fuse with the fuse p uller p rovid ed i n the main fuse b ox
c over.
6. Insp ec t the fuse. If it has b lown, rep lac e it wit h a sp are fuse of the
same rating . The sp are fuses are stored in the main fuse b ox c over in
the eng ine c omp artment.
7. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs.
Main fuse and fusible link
HG0127
The main fuses and fusib le link are d esig ned to mel t d uring an overload
to p revent d amag e to the wiring harness and elec tri c al eq uip ment.
Chec k the main fuses and fusib le link if any elec tr ic al c omp onent fails to

10-48op erate (exc ep t the starter motor) and other fuses
are g ood . A melted
main fuse or fusib le link must b e rep lac ed . Use onl y rep lac ements with
the same sp ec ified rating as the melted main fuse o r fusib le link. If a
main fuse or fusib le link b lows after it is rep lac e d , have the elec tric al sys-
tem c hec ked b y your nearest SUBARU d ealer.
Installation of accessories
Always c onsult your SUBARU d ealer b efore installing fog lig hts or any
other elec tric al eq uip ment in your vehic le. Suc h ac c essories may c ause
the elec tronic system to malfunc tion if they are in c orrec tly installed or if
they are not suited for the vehic le.