2000 SUBARU IMPREZA Owners Manual

Instruments and controls3-11
–
CONTINUED –
Clock
HG3002AA
The c loc k d isp lays the time when the ig nition switc
h is in the “ACC ” or
“ ON ” p ositions.
Setting the clock
Eac h time the “+ ” b utton is p ressed , the c loc k g ains 1 minute. By
hold ing the b utton d ep ressed , the c loc k c an b e p ut forward c ontinu-
ously. Pressing the “ –” b utton p uts the c loc k rearward .
Hazard warning flasher
HS0053
The hazard warning flasher is used to warn other d r ivers when you have
to p ark your vehic le und er emerg enc y c ond itions. Th e hazard warning

3-12flasher works with the ig nition switc h in any p osit
ion.
When you have to p ark your vehic le und er emerg enc y c ond itions, p ull off
the road safely and p ark away from the traffic if i t is p ossib le.
To turn on the hazard warning flasher, p ush the haz ard warning b utton
on the instrument p anel. To turn off the flasher, p ush the b utton ag ain.
NOTE When the hazard warning flasher is on, the turn signals do not work.
Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper-ates only when the ignition switch is in the “ON” position. In any
other position, the vehicle ’s lights will be out.
If you park vehicle on a roadside at night, use the hazard warningflasher to alert the other drivers.
HS0054 HS0055
Dimmer
Headlight flasher
The lig ht switc h op erates only when the ig nition sw itc h is in the “ON ”
p osition.
Headlights
To turn on the head lig hts, turn the knob on the end of the turn sig nal

Instruments and controls3-13
–
CONTINUED –
lever.
first p osition
Parking lig hts, instrument p anel illumination, tail lig hts, sid e marker
lig hts and lic ense p late lig ht are on.
sec ond p osition
Head lig hts, p arking lig hts, instrument p anel illumi nation, tail lig hts,
sid e marker lig hts and lic ense p late lig ht are on. High/low beam change (dimmer)
To c hang e from low b eam to hig h b eam, p ush the turn sig nal lever
forward . When the head lig hts are on hig h b eam, the hig h b eam ind i-
c ator lig ht “a ” on the instrment p anel is also on.
To switc h b ac k to low b eam, p ull the lever b ac k to the d etent p osition.
Headlight flasher CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
To flash the head lig hts, p ull the lever toward you and then release it.
The hig h b eam will stay on for as long as you hold the lever. The
head lig ht flasher works even thoug h the lig hting sw itc h is in the “OFF ”
p osition.
When the head lig hts are on hig h b eam, the hig h b eam ind ic ator lig ht
“ a ” on the instrment p anel also c omes on.
Daytime running light system (for CANADA models)
WARNING
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switchmust always be turned to the “a ” position when it is dark out-
side.

3-14The low b eam head lig hts will automatic ally c ome on
at red uc ed
b rig htness when the eng ine has started , und er the f ollowing c ond i-
tions:
The p arking b rake is fully released .
The automatic transmission selec tor lever is set at other than
the “P ” p osition.
The lig ht switc h is in the “OFF ” p osition.
Turn signal lever
HS0056
Right turn Left turn
To ac tivate the rig ht turn sig nal, p ush the turn si g nal lever up . To ac tivate
the left turn sig nal, p ush the turn sig nal lever d o wn. When the turn is fin-
ished , the lever will return automatic ally. If the lever d oes not return after
c ornering , return the lever to the neutral p osition b y hand .
To sig nal a lane c hang e, p ush the turn sig nal lever up or d own slig htly
and hold it d uring the lane c hang e. The turn sig nal ind ic ator lig hts will
flash in the d irec tion of the turn or lane c hang e. The lever will return auto-
matic ally to the neutral p osition when you release it.

Instruments and controls3-15
–
CONTINUED –
Illumination brightness control
HS0057
Brighten
Darken
When the lig hting switc h is in the “p ” or “a ” p osition, you c an ad just
b rig htness of the instrument p anel illumination for b etter visib ility.
To b rig hten, turn the c ontrol d ial c ounterc loc kwise .
To d arken, turn the c ontrol d ial c loc kwise.
Parking light switch
HS0058
The p arking lig ht switc h op erates reg ard less of the ig nition switc h p osi-
tion.
By p ushing the front end of this switc h, following lig hts will c ome on.
– p arking lig hts

3-16–
front and rear sid e marker lig hts
– tail lig hts
– lic ense p late lig hts
To turn off, p ush the rear end of the p arking lig ht switc h.
Avoid leaving these lig hts on for a long time b ec au se that will run d own
the b attery.
Fog light switch (if equipped)
The fog lig hts op erate only when the head lig hts are on low b eam.
Push the switc h to turn the fog lig hts on. To turn them off, p ush the switc h
ag ain.
HB2025BB
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the
windshield is sufficiently warmed by the defroster.Otherwise the washer fluid can freeze on the windshield, blocking
your view.

Instruments and controls3-17
–
CONTINUED –
CAUTION
Do not operate the washer continuously for more than ten se-
conds, or when the washer fluid tank is empty. This may cause
overheating of the washer motor. Check the washer fluid level fre-
quently, such as at fuel stops. Do not operate the wipers when the windshield or rear window
is dry. This may scratch the glass, damage the wiper blades and
cause the wiper motor to burn out. Before operating the wiper on
a dry windshield or rear window, always use the windshield
washer. In freezing weather, be sure that the wiper blades are not fro-
zen to the windshield or rear window before switching on thewipers. Attempting to operate the wiper with the blades frozen tothe window glass could cause not only the wiper blades to be
damaged but also the wiper motor to burn out. If the wiper bladeis frozen to the window glass, be sure to operate the defroster or
rear window defogger before turning on the wiper. If the wipers stop during operation because of ice or some oth-
er obstruction on the window, the wiper motor could burn outeven if the wiper switch is turned off. If this occurs, promptly stopthe vehicle in a safe place, turn the ignition switch to the “LOCK”
position and clean the window glass to allow proper wiper opera-tion. Use clean water if windshield washer fluid is unavailable. In
areas where water freezes in winter, use SUBARU Windshield
Washer Fluid or the equivalent. (See “Windshield washer fluid ”
section in chapter 10.)Also, when driving the vehicle when there are freezing tempera-tures, use non-freezing type wiper blades. Do not clean the wiper blades with gasoline or a solvent, such
as paint thinner or benzene. This will cause deterioration of thewiper blades.

3-18NOTE
The wiper operates only when the ignition switch is in the “ON”
or “ACC” position.
Clean your wiper blades and window glass periodically with a
washer solution to prevent streaking, and to remove accumulations
of road salt or road film. Keep the washer button depressed at leastfor 1 second so that washer solution will be sprinkled all over the
windshield or rear window. Grease, wax, insects or other material on the windshield or the
wiper blades results in jerky wiper operation and streaking on the
glass. If you cannot remove those streaks after operating the
washer or if the wiper operation is jerky, clean the outer surface ofthe windshield or rear window and the wiper blades using a sponge
or soft cloth with a neutral detergent or mild-abrasive cleaner. After
cleaning, rinse the window glass and wiper blades with clean water.The glass is clean if no beads form on the glass when you rinse with
water. If you cannot eliminate the streaking even after following this pro-
cedure, replace the wiper blades with new ones. Refer to the “Wiper
blade replacement ” section (chapter 10) for replacement instruc-
tions. Windshield wiper and washer switches Windshield wipers
HB2019BB