2000 Oldsmobile Intrigue Owner's Manuals

2-29
To stop the window while it is lowering, press the switch.
To raise the window, press and hold the switch forward.
The driver's window
controls also include a
lock
-out switch. Press
LOCK to stop front and rear
passengers from using their
window switches.
The driver can still operate all windows with the lock
on. Press the other side of the LOCK switch for normal
window operation.
Full Floating Horn
The full floating horn is designed so that you may press
anywhere on the steering wheel pad to sound the horn.
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can also raise it to the highest
level to give your legs more room when you exit and
enter the vehicle.
To tilt the wheel, hold the wheel and pull the lever
located on the left side of your steering column. Move
the wheel to a comfortable level, then release the lever
to lock the wheel in place.

2-30
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes your:

Turn Signal and Lane Change Indicator

Headlamp High/Low
-Beam Changer

Flash
-to-Pass

Headlamps

Taillamps

Parking Lamps
Turn Signal and Lane Change Indicator
The turn signal lever has two upward (for right) and
two downward (for left) positions. These positions allow
you to signal a turn or lane change.
To signal a turn, move the lever all the way up
or down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or lane change, if the arrow flashes
faster than normal, a signal bulb may be burned out and
other drivers won't see your turn signal.

2-31
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check for burned
-out bulbs and then check
the fuse (see ªFuses and Circuit Breakersº in the Index).
A chime will sound if you leave your turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low-Beam Changer
To change your headlamps
from low beam to high
beam, push the lever away
from you. To change back
to low beam, pull the lever
toward you.
To flash your high beams, pull the lever toward you and
release. The lever will return to the low
-beam position.
Please note that your fog lamps (if equipped) will not
be illuminated while the headlamps are in the
high
-beam mode.
Flash-to-Pass
With the lever in the low-beam position, pull the lever toward
you momentarily to switch to high beams (to signal you are
going to pass). If you have the headlamps on, they will return
to low beams when you release the lever.
Windshield Wipers
You can control the windshield wipers by moving the
lever with the wiper symbol on it up or down. This lever
is located on the right side of the steering wheel.
For a single wiping cycle, pull down on the lever to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on MIST longer.

2-32
You can set the wiper speed for a long delay or short
delay between wipes. This can be very useful in light
rain or snow. Push the lever up one click to INT
(intermittent), then turn the band, located on the lever, to
adjust the delay time. Turn the band down for a longer
delay, up for a shorter delay. The wiper speed can only
be adjusted when the lever is in the INT position, not in
HI or LO.
Be sure to clear the ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.Windshield Washer
At the end of the right-hand lever on the steering wheel,
there is a wiper symbol. To spray washer fluid on the
windshield, push the button on the end of the lever. The
wipers will run for several sweeps and then either stop
or return to your preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.

2-33
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control.
Don't use cruise control on slippery roads.
If your vehicle is in cruise control when the optional
traction control system begins to limit wheel spin,
the cruise control will automatically disengage.
(See ªTraction Control Systemº in the Index.)
When road conditions allow you to safely use it again,
you may turn the cruise control back on.Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE
button on the right side
of the instrument panel
to turn it on. A light on
the button will indicate
that the system is on.

2-34
2. Get up to the speed you want.
3. Press the COAST SET
button on your steering
wheel and release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RES ACCEL
button on your steering
wheel. You'll go right back
up to your chosen speed and
stay there.

2-35
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button on the steering wheel,
then release the button and the accelerator pedal.
You'll now cruise at the higher speed.

Press the RES ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the button. (To increase your speed
in very small amounts, press the RES ACCEL button
briefly and then release it. Each time you do this,
your vehicle will go 1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
on the steering wheel.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button on the steering wheel
until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button on the steering wheel briefly
and then release it. Each time you do this, you'll
go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.

2-36
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lamp controls are located on the multifunction lever on
the left of the steering wheel. They control these systems:

Headlamps

Taillamps

Parking Lamps

License Lamps

Sidemarker Lamps

Instrument Panel Lights