Page 33 of 1839
GENERAL -Precautions Before Service00-32
Other precautions:
DAvoid prolonged and repeated contact with oils,
particularly used engine oils.
DWear protective clothing, including impervious gloves
where practicable.
DAvoid contaminating clothes, particularly underpants, with
oil.
DDo not put oily rags in pockets, the use of overalls without
pockets will avoid this.
DDo not wear heavily soiled clothing and oil-impregnated
foot-wear. Overalls must be cleaned regularly and kept
separately from personal clothing.
DWhere there is a risk of eye contact, eye protection should
be worn, for example, chemical goggles or face shields;
in addition an eye wash facility should be provided.
DObtain First Aid treatment immediately for open cuts and
wounds.
DWash regularly with soap and water to ensure all oil is
removed, especially before meals (skin cleansers and
nail brushes will help). After cleaning, the application of
preparations containing lanolin to replace the natural skin
oils is advised.
DDo not use petrol, kerosine, diesel fuel, gas oil, thinners
or solvents for cleaning skin.
DUse barrier creams, applying them before each work
period, to help the removal of oil from the skin after work.
DIf skin disorders develop, obtain medical advice without
delay.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 43 of 1839
3 MSB - 00E00-009Model code
Engine modelTransmission modelFuel supply system
V68WMNHFR64M41-DOHC
Intercooler
V5M31 <5M/T>Electronically-controlled
highpressurefuelMNHFR6Intercooler
Turbo (3,200 mL)V5A51 <5A/T>highpressurefuel
distribution
GENERAL -Outline of Changes/Vehicle Identification00-1
GROUP 00
GENERAL
OUTLINE OF CHANGES
The following models have been added for England that are equipped with the 4M41 engine.
VEHICLE IDENTIFICATION
MODELS
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 46 of 1839
3 MSB-00E00-505
3. Details:
Contents of Attachment are to be added to GROUP 00 (GENERAL).
PRECAUTIONS BEFORE SERVICE
LEARNING FUNCTION OF GDI ENGINE
1. Purpose
On the GDI engine equipped cars, when replacement of the ECU (for engine control) or resetting
of the battery* has been performed, an idle learning function of the ECU (for engine control) will
be required.
The idle learning function will be completed by running the engine at idle by the following procedure.
NOTE:
*: Disconnection of ECU (for engine control) battery backup power supply (disconnection of battery
terminals or ECU connectors)
2. Idle Learning Procedure
(1) Start the engine, and warm up the engine until its coolant temperature reaches 85°C or higher.
When the engine coolant temperature is 85°C or higher, you have only to turn the ignition
switch to the ON position.
(2) Turn the ignition switch to the LOCK (OFF) position, and stop the engine.
(3) After lapse of ten or more seconds, restart the engine.
(4) Run the engine at idle for ten minutes under the following conditions.
DTransmission: Neutral (P range for automatic transmission)
DAir conditioner and heater: Not operational
DEngine coolant temperature: 83°C or higher
(5) Stop the engine.
(6) Restart the engine, and run it at idle for ten minutes under the following condition.
DTransmission: Neutral (P range for automatic transmission)
DAir conditioner: Operational (Temperature set at “maximum cool”, fan at high speed, and
windows fully opened)
DEngine coolant temperature: 83°C or higher
(7) Repeat steps (5) and (6).
NOTE:
1) When the atmospheric temperature is 20°C or more and the air conditioner has continuously
been operated, step (7) may be omitted.
2) During idling operation of the engine in steps (4) and (6), when engine operation switches
from lean operation to stoichiometric operation, engine stall can occur. In this case, clean the
throttle body (throttle valve) thoroughly, and then repeat step (1) and the subsequent steps.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 47 of 1839
GENERAL -Outline of Changes/Vehicle Identification00-1
GROUP 00
GENERAL
OUTLINE OF CHANGES
The following models are equipped with Mitsubishi Stability Control (MITSUBISHI SC) system.
VEHICLE IDENTIFICATION
MODELS
Model codeEngine modelTransmission modelFuel supply system
V68WMNDFL64M41-DOHC Intercool-V5M31 <5M/T>Electronically-con-
MNHFL6
er Turbo (3,200 mL)trolled high pressure
fuel distribution
MNHFR6
MYHFL6V5A51 <5A/T>
MYHFR6
MNXFL6V5M31 <5M/T>
MNXFR6
MYXFL6V5A51 <5A/T>
MYXFR6
V65WMNHCL66G74GDI (3,496 mL)V5M31 <5M/T>GDI
MNHCR6
MYHCL6V5A51 <5A/T>
MYHCR6
MNXCL6V5M31 <5M/T>
MNXCR6
MYXCL6V5A51 <5A/T>
MYXCR6
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 48 of 1839
GENERAL -Vehicle Identification00-2
Model codeEngine modelTransmission modelFuel supply system
V78WLNDFL64M41-DOHC Intercool-V5M31 <5M/T>Electronically-con-
LNHFL6
er Turbo (3,200 mL)trolled high pressure
fuel distribution
LNHFR6
LYHFL6V5A51 <5A/T>
LYHFR6
LNXFL6V5M31 <5M/T>
LNXFR6
LYXFL6V5A51 <5A/T>
LYXFR6
V75WLNHCL66G74GDI (3,496 mL)V5M31 <5M/T>GDI
LNHCR6
LYHCL6V5A51 <5A/T>
LYHCR6
LNXCL6V5M31 <5M/T>
LNXCR6
LYXCL6V5A51 <5A/T>
LYXCR6
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 49 of 1839
GENERAL -Vehicle Identification00-1
GROUP 00
GENERAL
INSPECTION SERVICE POINTS
DIAGNOSIS FUNCTION
WHEN USING THE WARNING LAMP
The diagnosis code read-out function, which is available by means of the neutral position indicator lamp,
has been discontinued .
VEHICLE IDENTIFICATION
MODELS
Model codeEngine modelTransmission modelFuel supply system
V64WMNDFL64D56 Intercooler Turbo
(2 477mL)
V5MT1 <5M/T>Injection
MNHFL6
(2,477mL)
V5M31 <5M/T>
MNHFR6
MNXFL6
MNXFR6
V68WMNDFL64M41-DOHC Intercool-
erTurbo(3 200mL)
V5M31 <5M/T>Electronically-con-
trolledhighpressure
MNHFL6
erTurbo(3,200mL)trolledhighpressure
fuel distribution
MNHFR6
MYHFL6V5A51 <5A/T>
MYHFR6
MNXFL6V5M31 <5M/T>
MNXFR6
MYXFL6V5A51 <5A/T>
MYXFR6
V65WMYHCL66G74 GDI (3,496 mL)V5A51 <5A/T>GDI
MYHCR6
MNXCL6V5M31 <5M/T>
MYXCL6V5A51 <5A/T>
MYXCR6
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 50 of 1839
GENERAL -Vehicle Identification00-2
Model codeEngine modelTransmission modelFuel supply system
V74WLNDFL64D56 Intercooler Turbo
(2 477mL)
V5MT1 <5M/T>Injection
LNHFL6
(2,477mL)
V5M31 <5M/T>
LNXFL6
V78WLNDFL64M41-DOHC Intercool-
erTurbo(3 200mL)
V5M31 <5M/T>Electronically-con-
trolledhighpressure
LNHFL6
erTurbo(3,200mL)trolledhighpressure
fuel distribution
LNHFR6
LYHFL6V5A51 <5A/T>
LYHFR6
LNXFL6V5M31 <5M/T>
LNXFR6
LYXFL6V5A51 <5A/T>
LYXFR6
V75WLYHCL66G74 GDI (3,496 mL)V5A51 <5A/T>GDI
LYHCR6
LNXCL6V5M31 <5M/T>
LYXCL6V5A51 <5A/T>
LYXCR6
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 55 of 1839
ENGINE <6G7>
Click on the applicable bookmark to selected the required model year.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
