2000 HONDA PRELUDE Owner's Manual (in English)

Tire
s

Recommended Tire Pressures for
Normal Driving

The following chart shows the recommended cold tire pressures for
most normal driving conditions and
speeds.

The compact spare tire pressure is:60 psi (420 kPa , 4.2 kgf/cm2)
These pressures are also give
n on
the tire information label on the driver's doorjamb. Tubeless tires have some ability to
self-seal if they are punctured.
However, because leakage is often
very slow, you should look closely
for punctures if a tire starts losing
pressure.

Tir e Pressur e Adjustmen t Fo r
Hig h Spee d Drivin g
Honda strongly recommends that
you not drive faster than posted speed limits and conditions allow. If
you decide it is safe to drive at high speeds, be sure to adjust the cold tire
pressures as shown below. If you do
not adjust the tire pressure, exces-
sive heat can build up and cause sudden tire failure. Be sure to readjust the pressure for
normal driving speeds. You should
wait until the tires are cold before adjusting the tire pressure.
Inspectio n
Every time you check inflation, you
should also examine the tires for
damage, foreign objects, and wear.
You should look for: Bumps or bulges in the tread or
side of the tire. Replace the tire if
you find either of these conditions. Cuts, splits, or cracks in the side
of the tire. Replace the tire if you
can see fabric or cord. Excessive tread wear.

Maintenanc e

Tire
s

Your car's tires have wear indicators molded into the tread. When the
tread wears down to that point, you
will see a 1/2 inch (12.7 mm) wide band running across the tread. Thisshows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A
tire that is this worn gives very little
traction on wet roads. You should
replace the tire if you can see the
tread wear indicator in three or more
places around the tire.
Maintenanc
e

In addition to proper inflation,
correct wheel alignment helps to decrease tire wear. If you find a tire
is worn unevenly, have your dealer
check the wheel alignment.
The tires were properly balanced by the factory. They may need to be
rebalanced at some time before theyare worn out. Have your dealer
check the tires if you feel a consis-
tent vibration while driving. A tire should always be rebalanced if it is
removed from the wheel for repair.
Make sure the installer balances the
wheels when you have new tires installed. This increases riding
comfort and tire life. Your car'soriginal tires were dynamic or "spin"
balanced at the factory. For best results, have the installer perform a
dynamic balance.
Improper wheel weights can damage
your car's aluminum wheels. Use only
Genuine Honda wheel weights for
balancing.

Maintenance

NOTIC
E

INDICATO
R

LOCATIO N

MARK S

TREA D WEA R

INDICATOR S

Tire
s

Tir e Rotatio n
To help increase tire life and distribute wear more evenly, youshould have the tires rotated every
7,500 miles (12,000 km). Move the
tires to the positions shown in the chart each time they are rotated. When shopping for replacement
tires, you may find that some tiresare "directional." This means they
are designed to rotate only in onedirection. If you use directional
tires, they should be rotated only

front-to-back.

Replacin g Tire s an d Wheel s
The tires that came with your car were selected to match the perform- ance capabilities of the car while
providing the best combination of
handling, ride comfort, and long life.
You should replace them with radial tires of the same size, load range,speed rating, and maximum cold tire
pressure rating (as shown on the
tire's sidewall). Mixing radial and
bias-ply tires on your car can reduce
its braking ability, traction, and steering accuracy. It is best to replace all four tires at
the same time. If that is not possible
or necessary, then replace the two
front tires or the two rear tires as a pair. Replacing just one tire canseriously affect your car's handling.
Maintenanc e
Installing improper tires on your
car can affect handling and stability. This can cause a crashin which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner's manual.

Fron
t Fron
t

(Fo r Non-directiona l
Tire s an d Wheels )(Fo
r Directiona l
Tire s an d Wheels )

Tire
s

The ABS works by comparing the speed of the wheels. When replacing
tires, use the same size originally supplied with the car. Tire size and
construction can affect wheel speed
and may cause the system to work in-

consistently.

If you ever need to replace a wheel,
make sure the wheel's specifications match those of the original wheel
that came on your car. Replacement
wheels are available at your Honda
dealer.
Wheel
s an d Tire s

Wheel:
16x6 1/2 JJ

Tire:

205/50R1687V

See page 266 for information about
DOT Tire Quality Grading.
Winte
r Drivin g

Tires that are marked "M
+ S" or
"All Season" on the sidewal
l have an
all-weather tread design. They should be suitable for most winter
driving conditions. Tires without
these markings are designed for optimum traction in dry conditions.
They may not provide adequate performance in winter driving.For the best performance in snowy
or icy conditions, you should installsnow tires or tire chains. They may
be required by local laws under certain conditions.

CONTINUED

Maintenanc e

Tire
s

Snow Tires
If you mount snow tires on your
Honda, make sure they are radial
tires of the same size and load range as the original tires. Mount snow
tires on all four wheels to balance
your car's handling in all weather conditions. Keep in mind the traction
provided by snow tires on dry roads
may not be as high as your car's
original equipment tires. You shoulddrive cautiously even when the roads
are clear. Check with the tire dealer
for maximum speed recommenda-

tions.
Tire Chains
Mount traction devices (cable-type)
only when required by driving
conditions or local laws. Make sure
they are the correct size for your
tires. Install them only on the front
tires.

When installing traction devices, follow the manufacturer'sinstructions and mount them as
tightly as you can. Drive slowly with
them installed. If you hear them coming in contact with the body or
chassis, stop and investigate. Make sure the traction devices are
installed tightly, and that they are
not contacting the brakes or
suspension.

Remove them as soon as you start
driving on cleared roads.
Traction devices that are the wrong
size or improperly installed can

damage your car's brake lines,

suspension, body, and wheels. Stop

driving if they are hitting any part of
the car.

Maintenanc e
NOTICE

Light
s

Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing your
car's visibility and the ability tosignal your intentions to other
drivers.
CONTINUED

Maintenanc e

PARKIN
G LIGH T
HEADLIGHT LO W BEA M
SID E MARKE R LIGH T
HEADLIGH
T HIG H BEA M
TUR N SIGNA L

Light
s

Check the following:
Headlights (low and high beam)
Parking lights
Taillights Brake lights
High-mount brake light
Turn signals Back-up lights
Hazard light function
License plate light
Side marker lights
Daytime running lights
(Canadian models)

If you find any bulbs are burned out,
replace them as soon as possible. Refer to the chart on page 265 to
determine what type of replacement
bulb is needed. TAILLIGHT/BRAK
E LIGH T
HIGH-MOUN
T BRAK E LIGH T

TAILLIGH T
BACK-U P LIGH T
SID E MARKE R LIGH T
TURN SIGNA L

LICENSE PLAT E LIGH T

Maintenanc e

Light
s
Headligh t Aimin g
The headlights were properly aimed when your car was new. You shouldcheck their aim if you regularly carry
heavy items in the trunk or pull a trailer. Each headlight assembly has
horizontal and vertical adjustment
indicators. These are set to their "0"
positions after the headlights are
aimed at the factory.
To check these settings:
1. Make sure the fuel tank is full. Park the vehicle on level ground.
2. The driver or someone who weighs the same should he sittingin the driver's seat for all checks
and adjustments.
Load the trunk with the items you
normally carry. HORIZONTA
L ANGL E GAUG E
If you usually pull a trailer, load it as
you would normally and attach it to
the car. Push down on the front and
rear bumpers several times to make sure the car is sitting normally.
3. Open the hood.
4. Check the horizontal angle gauge. The line on the adjustment screwindicator should line up with the
"0" mark on the gauge. VERTICA
L ANGL E GAUG E
5. Check the vertical angle gauge. The bubble should be centeredunderneath the longest scribe
mark on the gauge.
MaintenanceCONTINUED
BUBBLE