2000 Citroen C5 length

Downloaded from www.Manualslib.com manuals search engine GENERAL
6
GENERAL SPECIFICATION : DIMENSIONS
Exterior dimensions (mm)
Dimensions and interior volumes (mm)
VehiclesAll types
(except 3.0i V6 and 2.2 HDi)2.2 HDi 3.0i V6
Wheel base A 2750
Length (overall) B 4618
Rear track on the ground C 1509 1495 1493
Front track on the ground D 1544 1530 1528
Width (overall) E 1770
Height (overall) (
*) F 1476
Front overhang G 971
Rear overhang H 897
(
*) = Vehicle in running order (vehicle empty, levels topped up).
Elbow width, front1538
Elbow width, rear1520
Height of boot below parcel shelf554
Minimum floor width1170
Boot depth at floor level985
Volume of boot below parcel shelf (dm
3)456

Downloaded from www.Manualslib.com manuals search engine ENGINE
38
X = MAXI reusable
Engines : 6FZ - RFN - RLZ
Cylinder head tightening (m.daN) Cylinder head bolts
A= Washer thickness : 4 ± 0.2 mm.
X= Length under heads of the new bolts = 144.5 ± 0.5 mm. - Pre-tightening1.5 ± 0.1
- Tightening5 ± 0.1
- Untightening360° ± 2°
- Tightening2 ± 0.2
- Angular tightening285° ± 5°
(in the order 1 to 10)
NOTE : Oil the threads and
under the heads of the cylinder
head bolts. (Use engine oil or
Molykote G Rapid Plus.)
B1BP05BC
6FZ - RFN - RLZ
6FZ - RFN - RLZ
X= 147 mm
CYLINDER HEAD
B1DP16FC
NOTE : Retightening of the cylinder head
after a completed repair is prohibited.
Intervention est interdit.

Downloaded from www.Manualslib.com manuals search engine ENGINE
47
Engine : XFX
SPECIAL FEATURES : TIGHTENING TORQUES ( m.daN)
(8) Crankshaft bearings
Carry out the following operations :
- Clean the threads of the screws with a brush.
- Refit the screws with a coating of grease, on threads and under
heads "MOLYKOTE G RAPID PLUS".
- Check that the 8 centring pins are in place.
Tightening :
- Pre-tighteningM11to 3 ± 0.3 (Order from 1to8)
- Pre-tighteningM8to 1 ± 0.1(Orer fromAto H)
- TighteningM6 to 1 ± 0.1(Order from a to m)
- UntighteningM11to M8
Proceed screw by screw :
- TighteningM11to 3 ± 0.3(order from 1to 8), then
One angular tightening of 180°
- TighteningM8 to 1 ± 0,1(Order from Ato H), then
One angular tightening of180°
Max. length under heads of the screws M11 = 131.5 mm.
Max. length under heads of the screws M8 = 119 mm.
B1BP1GYD

Downloaded from www.Manualslib.com manuals search engine ENGINE
52
X = MAXIMUM reusable length
Engine : XFX
Cylinder head tightening (m.daN) Cylinder head bolts
NOTE : Oil the threads and under
the heads of the bolts. (Use engine
oil or Molykote G Rapid Plus). In the order indicated
Pre-tightening2 ± 0.2
UntighteningYES
Pre-tightening1.5 ± 0.2
Angular tightening225°
B1DP09VC
XFX
149.5 mm.
CYLINDER HEAD
B1DP18ZD

Downloaded from www.Manualslib.com manuals search engine ENGINE
56
Engines : RHY - RHZ
Cylinder head gasket identification
X = MAXIMUM reusable length NOTE : Grease the bolts on the threads and under the heads,
(using engine oil or Molykote G plus). ESSENTIAL
:
Tighten screw by screw in the
order indicated.
Pre-tightening2 ± 0.2
Tightening6 ± 0.6
Angular tightening220° ± 5°
(Order from 1 to 10)
B1DP05BC
RHY - RHZ
X = 133.3 mm Cylinder head tightening (m.daN) Cylinder head bolts
CYLINDER HEAD
B1DP15ECB1DP13PC

Downloaded from www.Manualslib.com manuals search engine ENGINE
58
Engine : 4HX
Cylinder head gasket identification
X = MAXIMUM reusable length NOTE : Grease the bolts on the threads and under the heads,
(using engine oil or Molykote G plus. ESSENTIAL : Tighten screw by screw
and in the order indicated.
Pre-tightening2 ± 0.2(Order 1 to 10)
Tightening6 ± 0.6(Order 1 to 10)
Untightening360°(Order 10 to 1)
Pre-tightening2 ± 0.2(Order 1 to 10)
Tightening6 ± 0.6(Order 1 to 10)
Angular tightening220°±5°(Order 1 to 10)
(In 2 attempts max.)
B1DP05BC
4HX
X = 134.5 mm Cylinder head tightening (m.daN)
4HXCylinder head bolts
CYLINDER HEAD (Continued)
B1DP15EC

Downloaded from www.Manualslib.com manuals search engine 142
INJECTION
FEATURES OF MULTIPOINT INJECTION SYSTEM
Exhaust system
(diagr.) Component Supplier Reference Observations
23
22
1
2EGR electrovalve
Upstream oxygen sensor
Downstream oxygen sensor
Air pump
Air inlet valveDELPHI
NGK
BOSCH (1)
NGK
BOSCH (1)
SAGEM
SAGEM97097 A
OZA 495-PG2
OZA 341-PG7
2 590 004
2 580 0345 way black connector, installed on the cylinder head.
4 way blue connector, length of wire : 555 mm,
Tighten to 4.5 ± 0.4 m.daN.
6 way black connector, length of wire : 1500 mm,
Tighten to 4.5 ± 0.4 m.daN.
2 way black connector, located under the battery.
Installed on the cylinder head.
(1) = EngineRFN

Downloaded from www.Manualslib.com manuals search engine 146
INJECTION
FEATURES OF MULTIPOINT INJECTION SYSTEM
Ignition circuit
(diagr.) Component Supplier Reference Observations
20Sparking plug
21Ignition coil block
12EGR electrovalve
4 and 7Exhaust gas temperature
sensor
6Precatalyser upstream proportional
oxygen sensor
2Catalytic converter downstream
oxygen sensorElectrode gap = 1 mm.
Tighten to 2,5 ± 0,2 m.daN.
6 way black connector.
6 way grey connector, installed on the cylinder head.
2 way brown connector, length of wire : 250 mm.
Tighten to 4,5 ± 0,4 m.daN.
6 way black connector, length of wire : 250 mm.
Tighten to 4,5 ± 0,4 m.daN.
4 way blue connector. BOSCH
BNA - R13-318
BBC 4.1 HP
2580105A
TS-200
LZA-A06-U1
OZA 538-PG1 DELPHI
SAGEM
HERAEUS
NGKExhaust system