2000 Citroen C5 air bleeding

Downloaded from www.Manualslib.com manuals search engine INJECTION
Idling - antipollution 111
Petrol injection 112
Emission standards 113 - 119
Prohibited operations : HDi 120 - 121
Safety requirements : HDi 122 - 123
Checking the fuel supply circuit 124 - 125
Checking the air supply circuit 126 - 130
Exhaust gas recycling 131 - 134
Checking turbo pressure 135 - 138
Features of injection systems 139 - 168
IGNITION
Sparking plugs 169
CLUTCH-GEARBOX
Speedometers 170
Clutch specifications 171 - 172
Gearbox and tyre specifications 173 - 174
BE4/5 gearbox controls 175 - 183
ML/5 gearbox controls 184 - 192
AL4-4HP20 gearbox controls 193 - 203
Driveshafts 204
AXLES-SUSPENSION
Wheels and tyres 205 - 211
Axle geometry 212 - 214
Front and rear axle 215 - 216Suspension 217 - 220
Steering specifications 221 - 222
BRAKES
Brake specifications 223 - 228
Handbrake adjustment 229
Bleeding and filling braking system 230 - 233
HYDRAULICS
Specifications 234 - 237
Suspension spheres 238 - 240
ELECTRICAL
Starter motors 241
Alternators 242
Charging circuit 243
AIR CONDITIONING
Quantities in R 134a aircon system 244
Special features 245
Pollen filter 246
Dryer cartridge 247 - 249
Checking oil level 250 - 251
Checking pressures 252
Air conditioning : 6FN-RFN-RLZ 253
Air conditioning circuit : XFX 254
Air conditioning circuit : RHY-RHZ 255
Air conditioning circuit : 4HX 256
INDEX
GENERAL
Identification of vehicles 1 - 4
General : Dimensions 5 - 6
Weight specifications 7 - 8
Towing specifications 9 - 10
Lifting / supporting the vehicle 11 - 14
Capacities 15 - 18
Lubricants 19 - 32
ENGINES
Engine specifications 34 - 58
Cylinder head marking / tightening
6FZ-RFN-RLZ 38
XFX 51 - 52
RHY-RLZ 55 - 56
4HX 57 - 58
Auxiliaries drive belt 59 - 68
Checking and setting valve timing 69 - 90
Power unit suspension 91 - 95
Exhaust system 96 - 100
Cooling system 101 - 107
Checking oil pressures 108
Oil filter 109
Filling and bleeding engine coolant 110

Downloaded from www.Manualslib.com manuals search engine ENGINE
110
FILLING AND BLEEDING THE COOLING CIRCUIT
TOOLS
[1] Filling cylinder: 4520-T
[2]Adaptor for filling cylinder: 4222-T.
ESSENTIAL : Respect the safety and cleanliness recommendations.
- The draining and refilling operations can be carried out by means of a WINN’S coolant replacement
apparatus or similar; it is essential to follow the instructions when using this apparatus.
Filling and bleeding
- Fit the cylinder adaptor [2] 4222-Tand the filling cylinder [1] 4520 -T.
- Use the coolant to ensure protection between - 15°Cand - 37°C.
- Slowly fill the system.
NOTE :Keep the cylinder filled up (visible level).
- Close each bleed screw as soon as the coolant flows without air bubbles.
- Start the engine : Engine speed 1500 rpm.
- Maintain this speed until the third cooling cycle (cooling fans have cut in and cut out).
- Stop the engine and allow it to cool down.
- Remove the filling cylinder [1] 4520-T and the adaptor [2] 4222-T.
- Top up the system to the maximum mark, with the engine cold.
- Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine B3FP13DC
BRAKES
232
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
With the bleeding apparatus
- Connect the bleeding apparatus [1] on the brake fluid reservoir (1).
- Adjust the apparatus pressure to 2 Bars.
For each circuit :
- Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
- Open the bleed screw, wait until the fluid is flowing out without air bubbles.
- Close the bleed screw.
- Remove the bleeding apparatus [1].
- Check the brake fluid level(Should be between «DANGER» level and«MAXI» level).
- Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE : Two operators are necessary.
For each circuit :
- Apply the brake pedal to place the circuit under pressure.
- Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
- Open the bleed screw, wait until the fluid is flowing out without air bubbles.
- Close the bleed screw.
- Remove the tool [1].
NOTE : Recommence the process a second time if that is necessary.
- Check the brake fluid level, (Should be between «DANGER»level and «MAXI»level).
- Fill if necessary with the approved and recommended synthetic brake fluid.