2000 Citroen C5 warning

Downloaded from www.Manualslib.com manuals search engine 181
BE4/5 GEARBOX SPECIFICATION
Engines : 6FZ - RFN - RLZ - RHY
CLUTCH
GEARBOX
DRIVESHAFTS
B2CP3CVDB2CP3CWCB2CP3CXC
Adjustments.
WARNING : Control cables should be adjusted each time the gearbox is
removed or cables changed.
WARNING : Do not use oil to detach the ball-joints.
To release the ball-joint, press at the centre «a»then pull the ball-joint upwards.
Ball-joints alone can be changed by removing the unlocking key with the aid of two
thin screwdrivers, unclip at «b».
To unlock the ball-joint, turn in the direction of the arrow «c».

Downloaded from www.Manualslib.com manuals search engine 190
CLUTCH
GEARBOX
DRIVESHAFTS
ML/5 GEARBOX SPECIFICATION
Engines : XFX – RHZ – 4HX
B2CP3CTDB2CP3BYC
Adjustments.
WARNING : Control cables should be adjusted each time the gearbox is
removed or cables changed.
WARNING : Do not use oil to detach the ball-joints.
To release the ball-joint, press at the centre«a»then pull the ball-joint upwards.
Ball-joints alone can be changed by removing the unlocking key with the aid of two
thin screwdrivers, unclip at «b».

Downloaded from www.Manualslib.com manuals search engine 196
RECOMMENDATIONS - PRECAUTIONS (AL 4 and 4 HP 20 AUTOMATIC GEARBOXES)
Engines : 6FZ - RFN - RHZ - XFX - 4HX
Towing
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised :
IMPERATIVE : - Put gear lever in position «N».
- Do not add any oil.
AL4 gearbox
- Do not exceed 50 km/h (30mph) over a distance of 50 km (30 m).
4 HP 20 gearbox
- Do not exceed 70 km/h (45mph) over a distance of 100 km (60 m).
Driving.
Never drive with the ignition switched off.
Never push the vehicle to try to start it;
(impossible with an automatic gearbox).
Lubrication
The automatic gearbox is only lubricated when the engine is running.Removing - refitting. (Automatic gearbox).
WARNING : Never place the gearbox on its lower casing
(risk of deforming the tray and damaging the hydraulic valve block).
Never use the connections as handles for raising, turning, holding or
pushing the gearbox.
ESSENTIAL :
- Fit the converter retaining peg while the gearbox is removed.
- Fit the centring peg to locate the gearbox on the engine:
(remove the converter retaining peg just before locating)
WARNING :With the emergency programme selected, an impact is
felt when changing from ‘‘P’’‘‘R’’or ‘‘N’’‘‘R’’.
Precautions to be taken
CLUTCH
GEARBOX
DRIVESHAFTS

Downloaded from www.Manualslib.com manuals search engine 197
RECOMMENDATIONS - PRECAUTIONS (AL 4 AUTOMATIC GEARBOX)
Engines : 6FZ - RFN - RHZ
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox
CLUTCH
GEARBOX
DRIVESHAFTS
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault :
- Gearbox in back-up mode with a replacement programme of
(the fault values are taken in substitution).
- Gearbox in back-up mode with an emergency programme
(3rd hydraulic).
WARNING : In the emergency programme, an impact is felt when
changing P/R, N/RandN/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms..
Oil quality – Oil level.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities : the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL : The gearbox must be replaced.Oil quality.
See corresponding operation.
An excessive oil level can result in the following consequences :
- Excessive heating of the oil.
- Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox (if necessary).
Check using a diagnostic tool.
Read the fault codes (engine and gearbox).
Absence de codes défauts.
Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.
Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters (this is essential after an initialisation of the ECU).

Downloaded from www.Manualslib.com manuals search engine 211
AXLES
SUSPENSION
STEERING
WHEELS AND TYRES
Special features (continued)
Under-inflation detection device.
- Vehicles equipped with the under-inflation detection system are identifiable by the presence of aluminium
valves.
- The under-inflation detection option is possible only on vehicles equipped with aluminium rims.
Composition :
- Four HFtransmitter modules(4)incorporated in the wheels in place of the valves, each including a lithium
battery with 10 yearsguaranteed life.
- AHF receiver incorporated in the communication module under the steering wheel (COM 2000).
- The tightening torque for the nut (5) is 0.6 ± 0.1 m.daN.
WARNING :
- Each time a tyre is replaced, the valve (6) must be replaced.
- Each time a rim is replaced, the seal (7) must be replaced.
- Each time a valve is replaced, it is necessary to have the transmitter recognised by the BSI, with
the aid of a diagnostic tool.
B2GPOOUC

Downloaded from www.Manualslib.com manuals search engine B3FP13BCAB3FP13CC
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
Filling the braking system.
WARNING : Use only those hydraulic fluids that are approved and recommended.
- Fill the brake fluid reservoir (1).
Bleeding the braking system.
WARNING: During the bleeding operation, take care to maintain the level of brake fluid in the reser-
voir and to top it up, using only brake fluid that is clean and clear.
Bleeding the primary circuit.
WARNING: The ABS should not be active during the bleeding operation.
- Front brake caliper: Bleed screw(5).
- Rear brake caliper: Bleed screw (6).
- Bleed each wheel cylinder, proceeding in the following order :
Front LH wheel.
Front RH wheel.
Rear LH wheel.
Rear RH wheel.BRAKES
231

Downloaded from www.Manualslib.com manuals search engine HYDRAULIC
SYSTEM
SPECIFICATION - IDENTIFICATION : SUSPENSION SPHERES
Hydractive 3 suspension
Front suspension sphere (1)
WARNING : The number marked on the suspension sphere is the reference no. of the component and not the Part No.
Engines Suspension sphere marking Volume (cc) Pressure (Bars) Diameter of damper hole (mm)
6FZ96 420 906 80 385 57 1.9/1.3
RHY-RHZ96 420 907 801.75/1.3
Rear suspension sphere (2)
All Types96 420 905 80 385 25 0.7/0.48
Hydractive 3+ suspension
Front suspension sphere (1)
RFN-RLZ96 420 908 80 385 44 0.9/0.48
XFX-4HX96 420 909 80 52
Rear suspension sphere (2)
All Types96 422 091 80 385 31 1.4/0.94
Hydractive regulator accumulator
Hydractive regulator Suspension sphere marking Volume (cc) Pressure (Bars)
Front (3)96 420 898 80 385 62
Rear (4)96 373 373 80 45
240

Downloaded from www.Manualslib.com manuals search engine 245
AIR
CONDITIONING
SPECIAL FEATURES : AIR CONDITIONING SYSTEM (R 134.a)
Tightening torques (m.daN).
Unions
Steel / Steel
Aluminium / Steel Ø Pipes
1.7 ± 3
1.3 ± 3 M 06
3.8 ± 3
2 ± 2 M 08
4 ± 3
2.5 ± 3 M 10
NOTE :For operations concerning draining, drying (empty), checking and refilling of a system: refer to BRE 0290.
WARNING : For R 134.a quantities : (see table on page: 250). NOTE : : Tighten the unions to the recommended torques using a retaining spanner whenever possible