1999 SUZUKI BALENO headlights

60G-74E

BEFORE DRIVING

MIRRORS

60G-03-013

Day-Night Rearview Mirror (if equipped)

To adjust the interior rearview mirror, set the

selector tab to the day position, then move

the mirror up, down, or sideways to obtain the

best view.

When driving at night, you can move the

selector tab to the night position to reduce

glare from the headlights of vehicles behind

you.
Always adjust the mirror with the

selector set to the day position.

Only use the night position if it is

necessary to reduce glare from the

headlights of vehicles behind you. Be

aware that in this position you may

not be able to see some objects that

could be seen in the day position.
Outside Rearview Mirrors

Adjust the outside rearview mirrors so you can

just see the side of your vehicle in the mirrors.

A WARNING

Be careful when judging the size or

distance of a vehicle or other object

seen in the side convex mirror (if

equipped). Be aware that objects look

smaller and appear farther away than

when seen in a flat mirror.

21

3-8

BEFORE DRIVING
6OG-74E

FRONT SEAT ADJUSTMENT

60G-03-014

Electric Mirrors (If equipped)

The switch to control the electric mirrors is

located on the instrument panel.You can only

adjust the mirrors when the ignition switch is

in the "ON" position. To adjust the mirrors:

1) Move the selector switch to the left or right

to select the mirror you wish to adjust.

2) Press the outer part of the switch that

corresponds to the direction in which you

wish to move the mirror.

3) Return the selector switch to the centre

position to help prevent unintended

adjustment.
72F-03-016

Never attempt to adjust the driver's seat

or seatback while driving. The seat or

seatback could move unexpectedly,

causing loss of control. Make sure that

the driver's seat and seatback are

properly adjusted before you start

driving.
72F-03-013

Adjusting Seat Position

The adjustment lever for each front seat is

located under the front of the seat, on the

inboard side. To adjust the seat position, pull

up on the adjustment lever and slide the seat

forward or rearward. After adjustment, try to

move the seat forward and rearward to ensure

that it is securely latched.

3-9
22

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E
INSPECTION AND MAINTENANCE

60G-09-031

Headlights

Open the bonnet. Disconnect the coupler.Turn

the lock ring counterclockwise and remove it.

Remove the sealing rubber.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in

emegency.
60G-09-037

Push the retaining spring forward and unhook

it. Then remove the bulb. Install a new bulb in

the reverse order of removal.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in emergency

situations.
70F-07-0S0E

Front Clearance/Turn Signal Light, Side

Turn Signal Light, rear Combination

Light, Registration Plate Light.

To remove a bulb holder from a light housing,

turn the holder counterclockwise and pull it

out. To install the holder, push the holder in

and turn it clockwise.

Two types (small oval and round) of bulb are

used for these lights. To remove and install a

small oval bulb, simply pull out or push in the

bulb.

109

9-26

INSPECTION AND MAINTENANCE

60G-74E

70F-07-051E

To remove a round bulb from a bulb holder,

push in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn it

clockwise. You can access the individual bulb

holders as described above:
60G-09-032

Front clearance light (A)

Open the bonnet.

Front turn signal light (B)

Trust this replacement job to your authorized

MARUTI dealer as the front bumper and the

headlight housing must be removed for this

job.
70F-07-054

Side turn signal light

Remove the lens by using a plain screw driver

covered with a soft cloth.

9-27
110

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4