1999 SUZUKI BALENO oil level

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

60G-74E
INSTRUMENT PANEL

60G-09-002

CAUTION

If you operate the engine with this

light on, severe engine damage can

result.

Do not rely on the Oil Pressure Light

to indicate the need to add oil. Be

sure to periodically check the engine

oil level (see pages 9-8 and 9-9).
70F-03-009

Charging Light

This light comes on when the ignition switch

is turned on, and goes out when the engine is

started. The light will come on and remain on

if there is something wrong with the battery

charging system. If the light comes on when

the engine is running, the charging system

should be inspected immediately by your

MARUTI dealer.

CAUTION

Do not continue driving long with the

charging light ON as this will drain the

battery 'dead'.
72F-05-027

"Malfunction Indicator" Light

Your vehicle has a computer-controlled

emission control system. A "Malfunction

Indicator" light is provided on the instrument

panel to indicate when it is necessary to have

the emission control system serviced. The

"Malfunction Indicator" light comes on when

the ignition switch is turned to "ON" and goes

out when the engine is started.

If the "Malfunction Indicator" light comes on

when the engine is running, there is a problem

with the emission control system. Take the

vehicle to your MARUTI dealer to have the

problem corrected.

CAUTION

Continuing to drive the vehicle when

the "Malfunction Indicator" light is on

can cause permanent damage to the

vehicle's emission control system, and

can affect fuel economy and

driveability.

5-4

INSTRUMENT PANEL
60G-74E

70F-03-042

Turn Signal Indicators

When you turn on the left or right turn signals,

the corresponding green arrow on the

instrument panel will flash along with the

respective turn signal lights. When you turn

on the hazard warning switch, both arrows will

flash along with all of the turn signal lights.

70F-03-043

Main Beam (High Beam) Indicator Light

This indicator comes on when headlight main

beams (high beams) are turned on.
SPEEDOMETER/ODOMETER/

TRIPMETER (if equipped)

60G-05-003

© Speedometer

© Odometer

(D Trip meter

© Trip meter reset knob

The speedometer indicates vehicle speed in

km/h.The odometer records the total distance

the vehicle has been driven. The tripmeter can

be used to measure the distance travelled on

short trips or between fuel stops. You can reset

the tripmeter to zero by pushing the reset

knob.
CAUTION

Keep track of your odometer reading

and check the maintenance schedule

regularly for required services.

Increased wear or damage to certain

parts can result from failure to perform

required services at the proper mileage

intervals and your warranty rights may

be affected.

5-5

42
41

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

60G-74E
INSPECTION AND MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE

The following table shows when regular

maintenance on your vehicle is required. This

table shows in kilometres and months when

inspections, adjustments, lubrication and other

services should be performed.

Maruti recommends that maintenance

on your Maruti vehicle be performed by

Maruti Authorised Dealer/Service

Station.
CAUTION

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use MARUTI

GENUINE PARTS (MGP).

85

9-2

INSPECTION AND MAINTENANCE

6OG-74E

PERIODIC MAINTENANCE SCHEDULE

A....Ad]ust. l....lnspect and correct or replace If necessary.

T....Tighten to specified torque. C....CIean.

R....Replace or change. O....Rotate

L....Lubrlcate.

Note:

This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals

respectively.

Interval: This interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ENGINE

1. Water pump drive belt (tension, wear)

2. Engine coolant (level, leakage)

3. Engine oil (API GRADE SF, SG, SH) & Oil filter

4. Cooling system hoses and connections (leakage, damage)

5. Engine bolts (All cylinder head and manifold fixings)

6. Engine mounting (loose, damage)

7. Valve clearance

8. Camshaft timing belt (damage, wear)

9. Exhaust system (noise, leakage or otherwise defective)

10. Positive crankcase ventilation System (Hoses, connections and valve;

IGNITION

1. Ignition wiring, (damage, deterioration)

2. Spark plugs (clean and adjust the gap)
FREE INSPECTIONS

1

1

A

I

R

I

-

-

-

_
5

6

I

I

I

I

-

-

A

-
10

12

I

I

R

I

T

T

-

-
PERIODIC MAINTENANCE SERVICE AT COST

20

24

I

R

R

I

-

-

A

I

Replace every 1,00,000 km

-

-

-
I

I

-

-
-

-

-

I
I

I

I

R
30

36

I

I

R

I

T

T

-

-

-

-

-

I
40

48

I

R

R

I

-

-

A

I

I

I

I

R
SO

60

I

I

R

I

T

T

-

-

-

-

-

I
60

72

R

R

R

I

-

-

A

I

I

I

I

R
70

84

A

I

R

I

T

T

-

-

-

-

-

I
80

96

I

R

R

I

-

-

A

I

I

I

I

R

9-3
86

60G-74E
INSPECTION AND MAINTENANCE

Interval: This interval should be Judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

FUEL

1. Air cleaner Paved-road

Dusty condition

2. Accelerator cable and Throttle shafts

3. Fuel tank cap, fuel lines & connections(leakage,damage)

4. Fuel filter (leakage)

CLUTCH AND TRANSMISSION

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage)

BRAKE

1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)

b. Brake drums & shoes

5. Master cylinder and wheel cylinder or calliper (oil leakage.boot kit)

6. Brake hoses and pipes (leakage, damage)
FREE

1

1
INSPECTIONS

5

6
10

12

Clean every 5,000 km. F
PERIODIC MAINTENANCE

20

24
30

36
40

48

Replace every 40,000 krr
50

60
SERVICE

60

72
AT

70

84
COST

80

96

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent

replacement if dust condition is severe.

-

-

I

I

I

I

-

I

I

I

-

-

I

I
I&L

I

I

I

I

I

I

I

I

I

I

-

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I

87

9-4

INSPECTION AND MAINTENANCE

60G-74E

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first
km (x 1,000)

months

WHEEL

1. Tyres (air pressure, abnormal wear, crack, ROTATION)

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

4. Rear wheel bearings (loose, damage)

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose.damage)

3. Rear spring (damage)

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

6. Suspension arms and Tension rods

STEERING

1. Steering wheel (play, loose)

2. Power steering fluid (level, leakage)/connections

3. All rods and arms (loose, damage, wear)

ELECTRICAL

1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

BODY

1. All chassis bolts and nuts (tighten)

2. All Latches, Hinges & Locks (function)
FREE

1

1
INSPECTIONS

5

6

Rotate and

I

-

-

I

-

-

I

-

-

I

I

I

I

-

I

I

-

-

I
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

I

I&L
10

12
PERIODIC

20

24

inspect every 5,000

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
30

36

km

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
MAINTENANCE

40

48

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
50

60

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
SERVICE

60

72

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
AT

70

84

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
COST

80

96

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L

9-5
88

60G-74E
INSPECTION AND MAINTENANCE

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)

1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap .*

6. Clean condenser with low pressure water

7. Check belt for frayed edges, change if necessary

8. Check all mounting bolts
FREE

1

1

I

I

I

I

—

I

I

_

-

-
INSPECTIONS

5

6

I

I

I

I

T

I

I

C

I

I
10

12

I

I

I

I

T

I

I

C

I

I
PERIODIC

20

24

I

I

I

I

T

I

I

C

I

I
30

36

I

I

I

I

T

I

I

C

I

I
MAINTENANCE

40

48

I

I

I

I

T

I

I

C

I

I
50

60

I

I

I

I

T

I

I

C

I

I
SERVICE

60

72

I

I

I

I

T

I

I

C

I

I
AT,

70

84

I

I

I

I

T

I

I

C

I

I
COST

80

96

I

I

I

I

T

I

I

C

I

I

The rear shock absorbers are filled with

high pressure gas. Never attempt to

disassemble it or throw it into a fire.

Avoid storing it near a heater or heating

device. When scrapping the absorber,

the gas must be released from the

absorber safely. Ask your dealer for

assistance.

89

9-6

INSPECTION AND MAINTENANCE
60G-74E

All maintenance should be carried

out with the Ignition switch in the

"OFF" position and the car parked

securely on the level ground unless

otherwise specified.

If you are In any way unsure of your

ability to undertake a task, then do

not start it but contact your Maruti

dealer to perform the work for you.
ENGINE OIL AND FILTER

Specified oil

Be sure that the engine oil you use comes

under the API classification of SF, SG or SH.

Select the appropriate oil viscosity according

to the above chart.

9-7
90
70F-07-004E

60G-74E
INSPECTION AND MAINTENANCE

60G-09-002E

Oil Level Cheek

It is important to keep the engine oil at the

correct level for proper lubrication of your

vehicle's engine. Check the oil level with the

vehicle on a level surface. The oil level

indication may be inaccurate if the vehicle is

on a slope. The oil level should be checked

either before starting the engine or at least 5

minutes after stopping the engine.

Pull out the oil dipstick, wipe oil off with a clean

cloth, insert the dipstick all the way into the

engine, then remove it again. The oil on the

stick should be between the upper and lower

limits shown on the stick. If the oil level

indication is near the lower limit, add enough

oil to raise the level to the upper limit.

91
60G-09-003E

Refilling

Remove the oil filler cap and pour oil slowly

through the filler hole to bring the oil level to the

upper limit on the dipstick. Be careful not to

overfill. Too much oil is almost as bad as too

little oil. After refilling, start the engine and allow

it to idle for about a minute. Stop the engine,

wait for five minutes and check the oil level again.

Changing Engine Oil and Fitter

Drain the engine oil while the engine is still

warm.

1) Remove the oil filler cap.

2) Place a drain pan under the drain plug.

3) Using the correct spanner remove the

drain plug and drain out the engine oil.
60G-09-004

The engine oil temperature may be high

enough to burn your fingers when the

drain plug Is loosened. Watt until the

drain plug is cool enough to touch with

your bare hands.

9-8

INSPECTION AND MAINTENANCE
60G-74E

New and used oil can be hazardous.

Children and pets may be harmed by

swallowing new or used oil. Keep new

and used oil and used oil fitters away

from children and pets.

Continuous contact with used engine

oil has been found to cause (skin)

cancer in laboratory animals. Brief

contact with used oil may irritate skin.

To minimize your exposure to used oil,

wear a long-sleeve shirt and

moistureproof gloves (such 'as

dishwashing gloves) when changing

oil. If oil contacts your skin, wash

thoroughly with soap and water.

Launder any clothing or rags if wet with

oil.

Recycle or properly dispose of used oil

and filters.

4) Reinstall the drain plug and gasket.

Tighten the plug to a torque of

5.0 kg-m (36.5 Ib-ft).
70F-07-010

Replace the oil filter

1) Using an oil filter wrench, turn the oil filter

counterclockwise and remove it.

2) Using a clean rag, wipe off the mounting

surface on the engine where the new filter

will be seated.

3) Smear a little engine oil around the rubber

gasket of the new oil filter.

4) Screw on the new filter by hand until the

filter gasket contacts the mounting

surface.
60G-09-005

CAUTION

To tighten the oil filter properly, it is

important to accurately identify the

position at which the filter gasket first

contacts the mounting surface.

5) Tighten the filter 3/4 turn from the point of

contact with the mounting surface, [or to

1.4 kg-m (10.5 Ib-ft)] using an oil filter

wrench.

9-9
92