1999 SUZUKI BALENO power steering

OTHER CONTROLS AND EQUIPMENTS
60G-74E

FRONT SEAT BACK POCKET

(if equipped)
REAR SPOILER WITH STOP LAMP

Other Controls (if equipped)

63B-06-022

This pocket is provided for holding light and

soft things such as gloves, newspapers or

magazines.

Do not put hard or breakable objects

In the pocket. If an accident occurs,

objects such as bottles, cans etc. can

injure the occupants in the rear seat.
60G-50-002E

Rear Spoiler is provided to improve

aerodynamic stability at higher speeds and

better asthetics. Stop Lamp (if equipped) is

fitted inside the Rear Spoiler. The stop lamp

will glow as and when the Brake Pedal is

depressed.

CAUTION

Never close the dicky door too hard or

with jerk or lift the dicky by holding

spoiler, rear spoiler may get damaged.

Close the dicky door gently and make

sure it is closed properly.
ALLOY WHEELS

Maintenance with tyre wears (if equipped)

60G-50-003E

Wider alloy wheels are provided in the vehicle

for better grip on the road and more fuel

economy. For balancing of wheels please

consult MARUTI authorised workshop.

CAUTION

Never try to remove the tyre from alloy

wheel rim in convention manner (by

hammering), it will damage the wheel

rim. Always insist on tyre changing

machine.

6-9
62

60G-74E

OTHER CONTROLS AND EQUIPMENT

POWER ANTENNA Other Controls

(if equipped)
LEATHER COVER

Steering Column Controls (if equipped)

60G-50-004E

60G-50-006E

Power antenna on the rear side will

automatically come up on switching on the

AM/FM receiver fitted in the vehicle.
For better control on steering wheel leather

cover is provided.
HIGH MOUNT STOP LAMP

(if equipped)

High mount stop lamp is provided with your

vehicle and is fitted on rear parcel tray. The

stop lamp will glow as when the brake pedal

will be depressed.

To change the bulb of the stop lamp, remove

the clips at both sides of the cover, by

pressing the inner pin inside so that the clip

gets loose and remove the bulb on turning

it anticlock-wise

The rating of bulb is 21W/12V.There are one

bulb in high mount stop lamp.

63

6-10

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

60G-74E
DRIVING TIPS AND SAFE DRIVING

DRIVING TIPS AND SAFE DRIVING

High Speed Driving 8-1

Driving on Hills 8-1

Driving on Slippery Roads 8-2

Driving on Wet Roads 8-2

Do's and Don'ts for Safe Driving 8-3

73

DRIVING TIPS AND SAFE DRIVING

60G-74E

70F-06-001

Wear Your Seat Belts at All Times.

The driver and passengers should

be property restrained at all times,

using the seatbelts provided. Refer

to the "SEATBELTS" section for

instructions on proper use of the

seatbelts.

Never drive while under the

influence of alcohol or other drugs.

Alcohol and drugs can seriously

impair your ability to drive safely,

greatly increasing the risk of injury

to yourself and others. You should

also avoid driving when you are

tired, sick, irritated, or under stress.
HIGH-SPEED DRIVING

When driving at a high-speed, pay attention to

the following:

• Stopping distance progressively increases

with vehicle speed. Apply the brakes far

enough ahead of the stopping point to

allow for the extra stopping distance.

• On rainy days, "Aquaplaning" can occur.

"Aquaplaning" is the loss of direct contact

between the road surface and the vehicle's

tyres due to a water film forming between

them. Steering or braking the vehicle while

"Aquaplaning" can be very difficult, and

loss of control can occur. Keep speed

down when the road surface is wet.

• At high speeds, the vehicle may be

affected by side winds. Therefore, reduce

speed and be prepared for unexpected

buffeting, which can occur at the exits of

tunnels, when passing by a cut of a hill, or

when being overtaken by large vehicles,

etc.

DRIVING ON HILLS

• When climbing steep hills, the vehicle may

begin to slow down and show a lack of

power. If this happens, you should change

to a lower gear so that the engine will again

be operating in its normal power range.

Change rapidly to prevent the vehicle from

losing momentum.
When driving down a hill, the engine

should be used for braking by shifting to

next lower gear.

Try not to hold the brake pedal down

too long or too often while going down

a steep or long hill. This could cause

the brakes to overheat, resulting in

reduced braking efficiency. Failure to

take this precaution could result in loss

of vehicle control.

CAUTION

When descending a down hill, NEVER

turn the ignition key to the "OFF"

position. Emission control system and

automatic transmission (if equipped)

damage may result.

DRIVING ON SLIPPERY ROADS

Under wet road conditions you should drive

at a lower speed than on dry roads due to

possible slippage of tyres during braking.

When driving on icy, snowcovered, or muddy

roads, reduce your speed and avoid sudden

acceleration, abrupt braking, or sharp steering

movements.

8-1

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

Interval: This interval should be Judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

FUEL

1. Air cleaner Paved-road

Dusty condition

2. Accelerator cable and Throttle shafts

3. Fuel tank cap, fuel lines & connections(leakage,damage)

4. Fuel filter (leakage)

CLUTCH AND TRANSMISSION

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage)

BRAKE

1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)

b. Brake drums & shoes

5. Master cylinder and wheel cylinder or calliper (oil leakage.boot kit)

6. Brake hoses and pipes (leakage, damage)
FREE

1

1
INSPECTIONS

5

6
10

12

Clean every 5,000 km. F
PERIODIC MAINTENANCE

20

24
30

36
40

48

Replace every 40,000 krr
50

60
SERVICE

60

72
AT

70

84
COST

80

96

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent

replacement if dust condition is severe.

-

-

I

I

I

I

-

I

I

I

-

-

I

I
I&L

I

I

I

I

I

I

I

I

I

I

-

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I

87

9-4

INSPECTION AND MAINTENANCE

60G-74E

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first
km (x 1,000)

months

WHEEL

1. Tyres (air pressure, abnormal wear, crack, ROTATION)

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

4. Rear wheel bearings (loose, damage)

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose.damage)

3. Rear spring (damage)

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

6. Suspension arms and Tension rods

STEERING

1. Steering wheel (play, loose)

2. Power steering fluid (level, leakage)/connections

3. All rods and arms (loose, damage, wear)

ELECTRICAL

1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

BODY

1. All chassis bolts and nuts (tighten)

2. All Latches, Hinges & Locks (function)
FREE

1

1
INSPECTIONS

5

6

Rotate and

I

-

-

I

-

-

I

-

-

I

I

I

I

-

I

I

-

-

I
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

I

I&L
10

12
PERIODIC

20

24

inspect every 5,000

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
30

36

km

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
MAINTENANCE

40

48

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
50

60

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
SERVICE

60

72

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
AT

70

84

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
COST

80

96

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L

9-5
88

60G-74E
INSPECTION AND MAINTENANCE

POWER STEERING (if equipped)

CLUTCH PEDAL

60G-09-017

Check the steering box case, vane pump and

hose connections for leaks or damage.

Power steering fluid

Check the fluid level by looking at the reservoir

in the engine compartment when the fluid is

cold (about room temperature).

Check that the fluid level is between the

"UPPER" and "LOWER" lines. If the fluid level

is near the "LOWER" line, fill it up to the

"UPPER" line with an automatic transmission

fluid equivalent to DEXRON»-IIE or

DEXRON'-III. Do not overfill.
63B-09-00SE

Power steering belt

The tension of the belt should be such that

there is a deflection of 8-10mm (0.31 -0.39 in.)

when you press your thumb midway between

the pulleys.

The belt should also be examined to ensure

that it is not damaged. If necessary, have the

belt adjusted or replaced by your MARUTI

dealer.
70F-07-034

Measure the clutch pedal piay by moving the

clutch pedal with your hand and measuring

the distance it moves until you feel slight

resistance. The play in the clutch pedal should

be between 15-20 mm (0.6 - 0.8 in). If the

play is more or less than the above, or clutch

dragging is felt with the pedal fully depressed,

have the clutch inspected by your MARUTI

dealer.

101

9-18

INSPECTION AND MAINTENANCE

60G-74E

TYRES

60G-09-018

The front and rear tyre pressure specifications

for your vehicle are listed on the Tyre Inflation

Pressure Label and in the "SPECIFICATIONS"

section at the end of this book. Both the front

and rear tyres should have the specified tyre

pressure.

Tyre Inspection

Inspect your vehicle's tyres periodically by

performing the following checks:

1) Measure the air pressure with a tyre

gauge. Adjust the pressure if necessary.
Air pressures should be checked

when the tyres are cold or you may

get inaccurate readings.

Check the inflation pressure from

time to time while inflating the tyre

gradually, until the specified

pressure is obtained.

Never underinf late or overinf late the

tyres.

Underinflation can cause unusual

handling characteristics or can

cause the rim to slip on the tyre

bead, resulting in an accident or

damage to the tyre or rim.

Overinflation can cause the tyre to

burst, resulting in personal injury.

Overinflation can also cause

unusual handling characteristics

which may result In an accident.
70F-07-037E

2) Check that the depth of the tread groove

is more than 1.6 mm (0.06 in). To help you

check this, the tyres have moulded in tread

wear indicators in the grooves. When the

indicators appear on the tread surface, the

remaining depth of the tread is 1.6 mm

(0.06 in) or less and the tyre should be

replaced.

3) Check for abnormal wear, cracks and

damage. Any tyres with cracks or other

damage should be replaced. If any tyres

show abnormal wear, have them inspected

by your MARUTI dealer.

9-19
102