1999 MITSUBISHI LANCER EVOLUTION VI service

MPI – On-vehicle Service13-68
ON-VEHICLE SERVICE
FUEL PUMP RESISTOR CHECK

Standard value: 0.45 – 0.65 Ω
The inspection procedures are the same as for the preceding
year-models.
FUEL PUMP RELAY No.2 CONTINUITY CHECK

Battery voltageTerminal No.
1234
Not supplied
Supplied
ENGINE CONTROL RELAY AND FUEL PUMP
RELAY CONTINUITY CHECK
Battery voltageTerminal No.
1234
Not supplied
Supplied
Equipment side connector for engine
control relay and fuel pump relay
Fuel pump relay
Engine control relay

FUEL SUPPLY – General / Fuel Tank13-69
FUEL SUPPLY
GENERAL
OUTLINE OF CHANGE
The service procedures have been revised as shown below because of change in the fuel pump & gauge
assembly and the fuel gauge unit.
FUEL TANK
REMOVAL AND INSTALLATION
4
32 1
65
7
11
Removal steps
1. Fuel hose
2. Fuel pump & gauge assembly
3. Packing
A4. High-pressure fuel hose5. Fuel pipe assembly
6. Fuel gauge unit
7. Packing
NOTE
The service procedures other than those mentioned above
remain unchanged.
INSTALLATION SERVICE POINT
AHIGH-PRESSURE FUEL HOSE INSTALLATION
Caution
After connecting the quick-release joint of the
high-pressure fuel hose, pull it gently in the direction
of removal to check that the hose is firmly connected
with a play of about 3 mm.

21A-1
CLUTCH
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
LUBRICANTS 2. . . . . . . . . . . . . . . . . . . . . . . . . . . ON-VEHICLE SERVICE 2. . . . . . . . . . . . . . . . . .
Clutch Pedal Inspection and Adjustment 2. . . . .
Bleeding 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH PEDAL 4. . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH CONTROL 5. . . . . . . . . . . . . . . . . . . . .
Clutch Master Cylinder 6. . . . . . . . . . . . . . . . . . . . .

CLUTCH –
General / Service Specifications /
Lubricants / On-vehicle Service21A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below.
SERVICE SPECIFICATIONS
ItemsStandard value
Clutch pedal height mm163.5–166.5
Clutch pedal clevis pin play mm1–3
Clutch pedal free play mm6–13
Distance between the clutch pedal and the toeboard when
the clutch is disengaged mm85 or more
LUBRICANTS
ItemsSpecified lubricantsQuantity
Clutch fluidBrake fluid DOT 3 or DOT 4As required
Push rod assemblyRubber grease
Boot
Release cylinder push rodMITSUBISHI genuine grease
Part No. 0101011
ON-VEHICLE SERVICE

CLUTCH PEDAL INSPECTION AND
ADJUSTMENT
1. Turn up the carpet, etc. under the clutch pedal.
2. Measure the clutch pedal height.
Standard value (A): 163.5 – 166.5 mm
3. If the height of the clutch pedal is outside the standard
value, loosen the locking nut and adjust the pedal height
to the standard value using the adjusting bolt or push
rod.
Clutch pedal height
A
Setting nutAdjusting bolt
Locking
nut
13 Nm

CLUTCH – On-vehicle Service21A-3
4. Measure the clutch pedal play.
Standard value (B): 1 – 3 mm
5. If the clutch pedal play is not within the standard value,
loosen the setting nut and move the push rod to adjust.
Caution
Do not push in the master cylinder push rod at this
time.
6. After completing the adjustments, confirm that the clutch
pedal free play (measured at the face of the pedal pad)
and the distance between the clutch pedal (the face of
the pedal pad) and the toeboard when the clutch is
disengaged are within the standard value ranges.
Standard value (C): 6–13 mm
Standard value (D): 85 mm or more
7. If the clutch pedal free play and the distance between
the clutch pedal and the toeboard when the clutch is
disengaged do not agree with the standard values, it
is probably the result of either air in the hydraulic system
or a faulty master cylinder or clutch. Bleed the air, or
disassembly and inspect the master cylinder or clutch.
8. Turn back the carpet, etc.
BLEEDING
Specified fluid: Brake fluid DOT 3 or DOT 4
Caution
Use the specified brake fluid. Avoid using a mixture of
the specified fluid and other fluid.
Clutch pedal clevis pin play
B
Clutch pedal free play
Distance between the clutch pedal and the
toeboard when the clutch is disengagedC
D

CLUTCH – Clutch Control21A-6
DISASSEMBLY AND REASSEMBLY
CLUTCH MASTER CYLINDER
13 Nm
6 7
3
1
2
Piston repair kitClutch fluid:
Brake fluid DOT3 or DOT4
Grease: Rubber grease
2 5
4
413
44 8
Disassembly steps
1. Piston stopper ring
A2. Push rod assembly
3. Boot
4. Piston assembly
5. Reservoir cap
6. Spring pin
7. Reservoir tank
8. Clutch master cylinder bodyCaution
Do not disassemble piston assembly.
INSTALLATION SERVICE POINT
APUSH ROD ASSEMBLY INSTALLATION
Set the length of the push rod assembly to the shown
dimension to make the adjustment of the clutch pedal easier.
122.5 mm

MANUAL TRANSMISSION OVERHAUL – General22B-2
GENERAL
OUTLINE OF CHANGE
Of the newly introduced transmission model, the service procedures for the following unit sections are
described.

Transmission

Clutch housing

Reverse idler gear

MANUAL TRANSMISSION OVERHAUL – Transmission22B-4
TRANSMISSION
DISASSEMBLY AND REASSEMBLY
1 2 34 5
6
78
910
11
18 Nm
69 Nm69 Nm 18 Nm
69 Nm
3.9 Nm32 Nm32 Nm
3
Disassembly steps
1. Transfer
J2. O-ring
3. Roll stopper bracket
4. Insulator washer
(EVOLUTION-IV only)
5. Shift cable bracketI6. Select lever
H7. Speedometer gear
8. Back-up lamp switch
9. Gasket
10. Plug
11. Gasket
NOTE:
For each service point, refer to Basic Manual. (Pub. No. S9806CNCP9)