1999 MITSUBISHI LANCER EVOLUTION VI Oxygen sensor

MPI – Troubleshooting13-49
INSPECTION PROCEDURE 41
MUT-II: Check if idling speed is unstable.
OK
MUT-II Data list
45 ISC servo position (Refer to P.13-60.)NGAdjust the basic idle speed. (Refer to P.13-30.)*
MUT-II Data list
28 A/C switch (Refer to P.13-58.)NGCheck the A/C switch and A/C relay system.
(Refer to P.13-39. INSPECTION PROCEDURE 29.)
OK
OK
MUT-II Data list
27 Power steering fluid pressure switch (Refer to P.13-58)NGCheck the power steering fluid pressure switch system.
(Refer to P.13-39, INSPECTION PROCEDURE 28.)
1. Inspect the intake of air into the air intake system.

Broken intake manifold gasket

Broken vacuum hose

PCV valve does not operate.

Broken air intake hose
2. Check the injector for clog.
OK
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0–400 mV and 600–1,000 mV during
idlingNGCheck the fuel pressure. (Refer to P.13-30.)*
OK
MUT-II Data list
11 Oxygen sensor
OK:600–1,000 mV during sudden racingNGCheck the oxygen sensor system. (Refer to P.13-42, INSPECTION
PROCEDURE 31.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-21.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-50
INSPECTION PROCEDURE 42
MUT-II: Engine stalling inspection when the engine is warmed up and idling.
OK
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
11 Oxygen sensor
OK:600–1,000 mV during sudden racingNGCheck the oxygen sensor system. (Refer to P.13-42, INSPECTION
PROCEDURE 31.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0–400 mV and 600–1,000 mV during
idlingNGCheck the fuel pressure. (Refer to P.13-30.)*
OK
MUT-II Data list
27 Power steering fluid pressure switch (Refer to P.13-58.)NGCheck the power steering fluid pressure switch system.
(Refer to P.13-39, INSPECTION PROCEDURE 28.)
OK
MUT-II Data list
28 A/C switch (Refer to P.13-58.)NGCheck the A/C switch and A/C relay system.
(Refer to P.13-39, INSPECTION PROCEDURE 29.)
OK
MUT-II Data list
45 ISC servo position (Refer to P.13-60.)NGAdjust the basic idle speed. (Refer to P.13-30.)*
1. Inspect the intake of air into the air intake system

Broken intake manifold gasket

Broken vacuum hose

PCV valve does not operate.

Broken air intake hose
2. Check the injector for clog.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-51
INSPECTION PROCEDURE 43
MUT-II: Check if hesitation, sag, stumble or poor acceleration occurs.
OK
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13-57.)NGCheck the throttle position sensor system. (Refer to P.13-9, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Actuator test
12 Waste gate solenoid valve (Refer to P.13-61.)NGCheck the waste gate solenoid valve system.
(Refer to P.13-45, INSPECTION PROCEDURE 35.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 600–1,000 mV during sudden racingNGCheck the oxygen sensor system. (Refer to P.13-42, INSPECTION
PROCEDURE 31.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0–400 mV and 600–1,000 mV during
idlingNGCheck the fuel pressure. (Refer to P.13-30.)*
OK
MUT-II Actuator test
09 Fuel pressure control valve (Refer to P.13-61.)NGCheck the fuel pressure control valve system.
(Refer to P.13-45, INSPECTION PROCEDURE 34.)
1. Inspect the intake of air into the air intake system

Broken intake manifold gasket

Broken vacuum hose

PCV valve does not operate.

Broken air intake hose
2. Check the injector for clog.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-52
INSPECTION PROCEDURE 44
MUT-II: Check if surge occurs.
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13-57.)NGCheck the throttle position sensor system. (Refer to P.13-9, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Data list
11 Oxygen sensor
OK:600–1,000 mV during sudden racingNGCheck the oxygen sensor system.
(Refer to P.13-42, INSPECTION PROCEDURE 31.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0–400 mV and 600–1,000 mV during
idlingNGCheck the fuel pressure. (Refer to P.13-30.)*
1. Inspect the intake of air into the air intake system

Broken intake manifold gasket

Broken vacuum hose

PCV valve does not operate.

Broken air intake hose
2. Check the injector for clog.OK
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).

MPI – Troubleshooting13-56
DATA LIST REFERENCE TABLE
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine:After having
warmed up
Air/fuel mixture is
made leaner when de-
When at 4,000 r/min,
engine is suddenly
decelerated200 mV or lessProcedure
No. 3113-42
made leaner when de-
celerating, and is made
richer when racing.
When engine is
suddenly raced600 – 1,000 mV
Engine:After having
warmed up
The oxygen sensor
si
gnal is used to check
Engine is idling400 mV or less
(Changes)
signal is used to check
the air/fuel mixture
ratio, and control
condition is also
checked by the ECU.2,500 r/min600 – 1,000 mV
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling17 – 43 Hz––
sensor
TION-IV>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min46 – 86 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling12 – 38 Hz––
sensor
TION-V, VI>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min36 – 76 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
13Intake air
temperature
sensor
Ignition switch: ON or
with engine runningWhen intake air
temperature is –20C–20CCode No.
1313-9
sensorWhen intake air
temperature is 0C0C
When intake air
temperature is 20C20C
When intake air
temperature is 40C40C
When intake air
temperature is 80C80C
NOTE
*: In a new vehicle [driven approximately 500 km or less], the air flow sensor output frequency is sometimes
10% higher than the standard frequency.

MPI – Troubleshooting13-65
Terminal
No.Normal condition Check condition (Engine condition) Check item
41Alternator FR terminal
Engine: Warm, idle (radiator fan: OFF)

Headlamp: OFF to ON

Brake lamp: OFF to ON

Rear defogger switch: OFF to ONVoltage drops by 0.2 –
3.5 V.
45A/C switchEngine: Idle speedTurn the A/C switch OFF0 – 3 V
Turn the A/C switch ON
(A/C compressor is oper-
ating)System voltage
60Oxygen sensor heater

Engine: Idling0 – 3 V

Engine speed: 5,000 r/minSystem voltage
71Ignition switch-STEngine: Cranking8 V or more
72Intake air temperature
sensorIgnition switch: ONWhen intake air tempera-
ture is 0C3.2 – 3.8 V
When intake air tempera-
ture is 20C2.3 – 2.9 V
When intake air tempera-
ture is 40C1.5 – 2.1 V
When intake air tempera-
ture is 80C0.4 – 1.0 V
76Oxygen sensorEngine: Running at 2,000 r/min after having been
warmed up (Check using a digital type voltmeter)0 ↔ 0.8 V
(Changes repeatedly)
80Backup power supplyIgnition switch: OFFSystem voltage
81Sensor impressed
voltageIgnition switch: ON4.5 – 5.5 V
82Ignition switch-IGIgnition switch: ONSystem voltage
83Engine coolant
temperature sensorIgnition switch: ONWhen engine coolant
temperature is 0C3.2 – 3.8 V
When engine coolant
temperature is 20C2.3 – 2.9 V
When engine coolant
temperature is 40C1.3 – 1.9 V
When engine coolant
temperature is 80C0.3 – 0.9 V
84Throttle position sensorIgnition switch: ONSet throttle valve to idle
position0.3 – 1.0 V
Fully open throttle valve4.5 – 5.5 V
85Barometric pressure
sensor
Ignition switch: ONWhen altitude is 0 m3.7 – 4.3 V
sensor
When altitude is 1,200 m3.2 – 3.8 V
86Vehicle speed sensor
Ignition switch: ON

Move the vehicle slowly forward0 ↔ 5 V
(Changes repeatedly)

MPI – Troubleshooting13-67
RESISTANCE AND CONTINUITY BETWEEN HARNESS SIDE CONNECTORS AND TERMINALS
Engine-ECU Harness Side Connector Terminal Arrangement
Terminal No.Inspection itemNormal condition (Check condition)
1 – 12No.1 injector2 – 3 Ω (At 20C)
14 – 12No.2 injector
2 – 12No.3 injector
15 – 12No.4 injector
3 – 12Fuel pressure control valve28 – 36 Ω (At 20C)
4 – 12Stepper motor coil (A1)28 – 33 Ω (At 20C)
17 – 12Stepper motor coil (A2)
5 – 12Stepper motor coil (B1)
18 – 12Stepper motor coil (B2)
6 – 12Secondary air control solenoid valve28 – 36 Ω (At 20C)
11 – 12Wastegate solenoid valve62 – 74 Ω (At 20C)
60 – 12Oxygen sensor heater
11 – 18 Ω (at 20C)
13 – Body earthEngine-ECU earthContinuity established (0 Ω)
26 – Body earth
72 – 92Intake air temperature sensor5.3 – 6.7 kΩ (When intake air temperature is 0C)
2.3 – 3.0 kΩ (When intake air temperature is 20C)
1.0 – 1.5 kΩ (When intake air temperature is 40C)
0.30 – 0.42 kΩ (When intake air temperature is 80C)
74 – 77High temperature sensor3 Ω or less
83 – 92Engine coolant temperature sensor5.1 – 6.5 kΩ (When coolant temperature is 0C)
2.1 – 2.7 kΩ (When coolant temperature is 20C)
0.9 – 1.3 kΩ (When coolant temperature is 40C)
0.26 – 0.36 kΩ (When coolant temperature is 80C)
87 – 92Idle position switchContinuity established (when throttle valve is at idle
position)
No continuity (when throttle valve is slightly open)
91 – Body earth–Continuity established