1999 MITSUBISHI LANCER EVOLUTION VI transmission

00
11
13
21
22
26
27
33
35
37
42
51
52
54
55
General . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Transmission . . . . . . . . . . .
Front Axle . . . . . . . . . . . . . . . . . . . . . .
Rear Axle . . . . . . . . . . . . . . . . . . . . . .
Front Suspension . . . . . . . . . . . . . . .
Service Brakes . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . .
Body . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Electrical . . . . . . . . . . . . . .
Electrical Wiring . . . . . . . . . . . . . . . .
WORKSHOP MANUAL
SUPPLEMENT
FOREWORD
This Workshop Manual contains procedures for
service mechanics, including removal, disassembly,
inspection, adjustment, reassembly and
installation. Use the following manuals in
combination with this manual as required.
TECHNICAL INFORMATION MANUAL
N9806CNCP9
N9806CNCP9-A
WORKSHOP MANUAL
S9806CNCP9
All information, illustrations and product
descriptions contained in this manual are current
as at the time of publication. We, however, reserve
the right to make changes at any time without prior
notice or obligation.
The EVOLUTION -VI is sold exclusively through
RALLIART Inc. Since the EVOLUTION-VI is a rally-
based model, it will not be warranted and will not be
homologated for general production. Therefore, any
service matters on the EVOLUTION-VI should be
inquired to RALLIART Inc. as usual.
EVOLUTION-VI

Mitsubishi Motors Corporation March 1999
Interior and Supplemental
Restraint System (SRS) . . . . . . . . .
.
Heater, Air Conditioner and
Ventilation . . . . . . . . . . . . . . . . . . . . .
.

GENERAL – How to Use This Manual00-3
HOW TO USE THIS MANUAL
SCOPE OF MAINTENANCE, REPAIR
AND SERVICING EXPLANATIONS
This manual provides explanations, etc. concerning
procedures for the inspection, maintenance, repair
and servicing of the subject model. Note, however,
that for engine and transmission-related component
parts, this manual covers only on-vehicle
inspections, adjustments, and the removal and
installation procedures for major components.
For detailed information concerning the inspection,
checking, adjustment, disassembly and reassembly
of the engine, transmission and major components
after they have been removed from the vehicle,
please refer to separate manuals covering the
engine and the transmission.
ON-VEHICLE SERVICE
“On-vehicle Service” is procedures for performing
inspections and adjustments of particularly
important locations with regard to the construction
and for maintenance and servicing, but other
inspection (for looseness, play, cracking, damage,
etc.) must also be performed.
INSPECTION
Under this title are presented inspection and
checking procedures to be performed by using
special tools and measuring instruments and by
feeling, but, for actual maintenance and servicing
procedures, visual inspections should always be
performed as well.
DEFINITION OF TERMS
STANDARD VALUE
Indicates the value used as the standard for judging
the quality of a part or assembly on inspection
or the value to which the part or assembly is
corrected and adjusted. It is given by tolerance.
LIMIT
Shows the standard for judging the quality of a
part or assembly on inspection and means the
maximum or minimum value within which the part
or assembly must be kept functionally or in strength.
It is a value established outside the range of
standard value.
REFERENCE VALUE
Indicates the adjustment value prior to starting the
work (presented in order to facilitate assembly and
adjustment procedures, and so they can be
completed in a shorter time).
CAUTION
Indicates the presentation of information particularly
vital to the worker during the performance of
maintenance and servicing procedures in order to
avoid the possibility of injury to the worker, or
damage to component parts, or a reduction of
component or vehicle function or performance, etc.
INDICATION OF TIGHTENING TORQUE
The tightening torque shown in this manual is a
basic value with a tolerance of ±10% except the
following cases when the upper and lower limits
of tightening torque are given.
(1) The tolerance of the basic value is within ±10%.
(2) Special bolts or the like are in use.
(3) Special tightening methods are used.

GENERAL – How to Use This Manual00-4
EXPLANATION OF MANUAL CONTENTS
Indicates procedures to be performed
before the work in that section is started,
and procedures to be performed after
the work in that section is finished.
Indicates (by symbols) where lubrica-
tion is necessary.
Maintenance and Servicing Procedures
The numbers provided within the diagram indi-
cate the sequence for maintenance and servic-
ing procedures.
Removal steps:
The part designation number corresponds
to the number in the illustration to indicate
removal steps.
Disassembly steps:
The part designation number corresponds
to the number in the illustration to indicate
disassembly steps.Installation steps:
Specified in case installation is impossible
in reverse order of removal steps. Omitted
if installation is possible in reverse order of
removal steps.
Reassembly steps:
Specified in case reassembly is impossible
in reverse order of disassembly steps.
Omitted if reassemby is possible in reverse
order of disassembly steps.
Classifications of Major Maintenance/Service Points
When there are major points relative to maintenance and servicing procedures
(such as essential maintenance and service points, maintenance and service stan-
dard values, information regarding the use of special tools, etc.), these are ar-
ranged together as major maintenance and service points and explained in detail.
A: Indicates that there are essential points for removal or disassembly.
A: Indicates that there are essential points for installation or reassembly.
Symbols for Lubrication, Sealants and Adhesives
Information concerning the locations for lubrica-
tion and for application of sealants and adhe-
sives is provided, by using symbols, in the dia-
gram of component parts or on the page follow-
ing the component parts page, and explained.: Grease
(multipurpose grease unless there is a
brand or type specified)
: Sealant or adhesive
: Brake fluid or automatic transmission fluid
: Engine oil, gear oil or air conditioner com-
pressor oil
: Adhesive tape or butyl rubber tape
Component Diagram
A diagram of the component parts is
provided near the front of each section
in order to give a reader a better under-
standing of the installed condition of
component parts.

GENERAL – Models00-14
MODELS

Model
codeClass
codeModel
yearGradeEngine modelTransmission
modelFuel supply
system
E-CN9ASNDF’97RS4G63 (2,000-DOHC –
16 valves-intercooler
W5M51
(4WD-5M/T)
Electronically
controlledfuel
SRGF’97GSR
16 valves-intercooler
turbo)
(4WD-5M/T)controlled fuel
injection (MPI)
Applicable serial numbers
E-CN9A: CN9A – 0000001


Model
codeClass
codeModel
yearGradeEngine modelTransmission
modelFuel supply
system
GF-CP9ASNDF’98EVOLUTION-V RS4G63 (2,000-DOHC –
16 valves intercooler
W5M51
(4WD 5M/T)
MPI
SNGF’98EVOLUTION-V
GSR
16 valves-intercooler
turbo)(4WD-5M/T)
Applicable serial numbers
GF-CP9A: CP9A – 0000001


Model
codeClass
codeModel
yearGradeEngine modelTransmission
modelFuel supply
system
GF-CP9ASNDF’99EVOLUTION-VI
RS4G63 (2,000-DOHC –
16 valves-intercooler
turbo)
W5M51
(4WD-5M/T)MPI
SNGF’99EVOLUTION-VI
GSRturbo)
Applicable serial numbers
GF-CP9A: CP9A – 0100001

MPI – Troubleshooting13-56
DATA LIST REFERENCE TABLE
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine:After having
warmed up
Air/fuel mixture is
made leaner when de-
When at 4,000 r/min,
engine is suddenly
decelerated200 mV or lessProcedure
No. 3113-42
made leaner when de-
celerating, and is made
richer when racing.
When engine is
suddenly raced600 – 1,000 mV
Engine:After having
warmed up
The oxygen sensor
si
gnal is used to check
Engine is idling400 mV or less
(Changes)
signal is used to check
the air/fuel mixture
ratio, and control
condition is also
checked by the ECU.2,500 r/min600 – 1,000 mV
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling17 – 43 Hz––
sensor
TION-IV>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min46 – 86 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
12Air flow
sensor*
Engine coolant
tem
perature: 80 –
Engine is idling12 – 38 Hz––
sensor
TION-V, VI>temperature: 80
95C

Lamps, electric
li f d ll
2,500 r/min36 – 76 Hzp
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T:
P range)Engine is racedFrequency
increases in
response to
racing
13Intake air
temperature
sensor
Ignition switch: ON or
with engine runningWhen intake air
temperature is –20C–20CCode No.
1313-9
sensorWhen intake air
temperature is 0C0C
When intake air
temperature is 20C20C
When intake air
temperature is 40C40C
When intake air
temperature is 80C80C
NOTE
*: In a new vehicle [driven approximately 500 km or less], the air flow sensor output frequency is sometimes
10% higher than the standard frequency.

MPI – Troubleshooting13-59
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
41Injectors*1
TION-IV>Engine: CrankingWhen engine
coolant temperature
is 0C (injection is
carried out for all
cylinders
simultaneously)27 – 41 ms––
When engine
coolant temperature
is 20C14 – 22 ms
When engine
coolant temperature
is 80C3.9 – 5.9 ms
Injectors*2
TION-IV>

Engine coolant
temperature:
80–95C
Engine is idling1.2 – 2.4 ms
TION-IV>80–95C

Lamps, electric
cooling fan and all
accessories: OFF
2,500 r/min1.0 – 2.2 ms
accessories: OFF

Transmission:
Neutral (A/T :
P range)When engine is
suddenly racedIncreases
41Injectors*1
TION-V, VI>Engine: CrankingWhen engine
coolant temperature
is 0C27 – 40 ms––
When engine
coolant temperature
is 20C14.5 – 21.7 ms
When engine
coolant temperature
is 80C3.8 – 5.6 ms
Injectors*2
TION-V VI>

Engine coolant
temperature:
80–95C
Engine is idling0.9 – 2.1 ms
TION-V, VI>80–95C

Lamps, electric
cooling fan and all
accessories: OFF
2,500 r/min0.7 – 1.9 ms
accessories: OFF

Transmission:
Neutral (A/T :
P range)When engine is
suddenly racedIncreases
NOTE
*1: The injector drive time represents the time when the cranking speed is at 250 r/min or below when
the power supply voltage is 11 V.
*
2: In a new vehicle [driven approximately 500 km or less], the injector drive time is sometimes 10%
longer than the standard time.

MPI – Troubleshooting13-60
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
44Ignition coils
and power
transistors
having warmed up

Timing lamp is set.
(The timing lampEngine is idling3ATDC –
13BTDC––
TION-IV>
(tgp
is set in order to
check actual
ignition timing.)2,500 r/min24 – 44BTDC
44Ignition coils
and power
transistors

Engine: After
having warmed up

Timing lamp is set
Engine is idling0 – 13BTDC––
transistors
TION-V, VI>
Timing lamp is set.
2,500 r/min24 – 44BTDC
45ISC
(stepper)
motor
position *

Engine coolant
temperature: 80 –
90C

Lam
ps, electric
A/C switch: OFF2 – 25 steps––
position
Lamps, electric
cooling fan and all
accessories: OFF

Transmission:
Neutral (A/T :
P range)
Idl iti
A/C switch:
OFF → ONIncreases by
10 – 70 steps
g)

Idle position
switch: ON

Engine: Idling

When A/C switch
is ON, A/C
compressor should
be operating
A/C switch: OFF

Select lever:
N range →
D rangeIncreases by
5 – 50 steps
49A/C relayEngine: After having
warmed up/Engine is
idlingA/C switch: OFFOFF (Compressor
clutch is not
operating)Procedure
No. 2913-39
A/C switch: ONON (Compressor
clutch is
operating)
NOTE
*: In a new vehicle [driven approximately 500 km or less], the stepper motor has sometimes 30 steps
greater than the standard value.
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.

22B-1
MANUAL
TRANSMISSION
OVERHAUL
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 3. . . . . . . . . . . . . . . . . . . . . . . . TRANSMISSION 4. . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH HOUSING 5. . . . . . . . . . . . . . . . . . . . . .
REVERSE IDLER GEAR 6. . . . . . . . . . . . . . . . .