1999 LAND ROVER DISCOVERY belt

RESTRAINT SYSTEMS
REPAIRS 75-15
Seat belt - rear - side
$% 76.73.23
Remove
1.Remove 'D' post trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - 'D' post.
2.Remove loadspace side trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - side - loadspace.
3.Remove cap from seat belt lower anchorage
bolt.
4.Remove lower anchorage bolt.
5.Remove cover from seat belt upper anchorage
bolt.
6.Remove upper anchorage bolt.
7.Remove bolt securing seat belt reel to body.
8.Remove seat belt.
Refit
1.Fit seat belt reel to body and tighten bolt to 32
Nm (24 lbf.ft).
2.Fit seat belt upper anchorage to body and
tighten bolt to 50 Nm (37 lbf.ft).
3.Fit cover to upper anchorage bolt.
4.Fit seat belt lower anchorage to body and
tighten bolt to 32 Nm (24 lbf.ft).
5.Fit cap to lower anchorage bolt.
6.Fit loadspace side trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - side - loadspace.
7.Fit 'D' post trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - 'D' post.

RESTRAINT SYSTEMS
75-16 REPAIRS
Mounting - seat belt - 'B' post
$% 76.73.26
Remove
1.Release front door aperture seal from 'B' post.
2.Release rear door aperture seal from 'B' post.
3.Release clip securing upper 'B' post trim.
4.Remove 'B' post upper trim.
5.Remove nut securing seat belt upper
anchorage to mounting. 6.Remove 2 Torx bolts securing mounting to 'B'
post.
7.Remove mounting.
Refit
1.Fit mounting to 'B' post and tighten Torx bolts to
22 Nm (16 lbf.ft).
2.Fit seat belt upper anchorage to mounting and
tighten nut to 32 Nm (24 lbf.ft).
3.Secure trim casing to 'B' post with clip.
4.Fit front and rear door aperture seals to 'B'
post.

RESTRAINT SYSTEMS
REPAIRS 75-17
Seat belts - third row
$% 76.73.28/21
Remove
1.Remove 'D' post trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - 'D' post.
2.Remove seat belt upper anchorage bolt and
collect spacer.
3.Release access panel from loadspace side trim
casing.
4.Remove access panel.
5.Remove bolt securing seat belt reel to body.
6.Remove cap from seat belt lower anchorage
bolt.
7.Remove lower anchorage bolt and collect
washers.
8.Remove seat belt.Refit
1.Fit seat belt lower anchorage to body and
tighten bolt to 32 Nm (24 lbf.ft). Fit cap to bolt.
2.Fit seat belt reel to body and tighten bolt to 50
Nm (37 lbf.ft).
3.Fit seat belt upper anchorage and tighten bolt
to 50 Nm (37 lbf.ft).
4.Fit access panel to luggage compartment side
trim casing.
5.Fit 'D' post trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - 'D' post.

RESTRAINT SYSTEMS
75-18 REPAIRS
Pre-tensioner - front seat belt
$% 76.73.30
WARNING: It is imperative that before any work
is undertaken on the SRS system the appropriate
information is read thoroughly.
WARNING: Always disconnect both battery leads
before beginning work on the SRS system.
Disconnect the negative battery lead first. Never
reverse connect the battery.
Remove
1.Remove the key from the starter switch.
Disconnect both battery leads, negative lead
first. Wait ten minutes before starting work.
2.Remove front seat.

+ SEATS, REPAIRS, Seat - front.
3.Release cable tie securing pre-tensioner
harness to seat.
4.Remove Torx screw securing pre-tensioner to
seat.
5.Remove pre-tensioner.
WARNING: Store the airbag module or seat
belt pre-tensioner in a designated storage
area. If there is no designated storage area
available, store in the locked luggage
compartment/loadspace of the vehicle and
inform the workshop supervisor.Refit
1.Fit pre-tensioner to seat and tighten Torx bolt to
32 Nm (24 lbf.ft).
2.Secure harness to seat with new cable tie.
3.Fit front seat.

+ SEATS, REPAIRS, Seat - front.
4.Connect battery leads, earth lead last.

RESTRAINT SYSTEMS
REPAIRS 75-19
Pre-tensioner - seat belt - front -
deployment - in vehicle
$% 76.73.77
These guidelines are written to aid authorised
personnel to carry out the safe disposal of air bag
modules when removed from the vehicle.
Deploy
It is imperative that before any work is
undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Position front seat fully rearwards to access
seat belt pre-tensioner multiplug.
2.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary Restraint System
Precautions.
3.Disconnect multiplug from seat belt pre-
tensioner.
4.Check condition of deployment tool LRT-86-
003 and associated fly leads.5.Connect deployment tool fly lead LRT-86-003/
04 to seat belt pre-tensioner.
6.Connect deployment tool LRT-86-003 to
deployment tool fly lead LRT-86-003/04.
7.Connect deployment tool LRT-86-003 to
battery.
WARNING: Ensure all personnel are at least
15 metres (50 feet) away from the air bag
module.
8.Press deployment tool operating button to
deploy seat belt pre-tensioner.
9.Disconnect deployment tool from battery.
WARNING: During deployment parts of the
air bag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the air bag module.
10.Disconnect deployment tool fly lead from seat
belt pre-tensioner.
11. Do not re-use or salvage any parts of the
SRS system.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.

RESTRAINT SYSTEMS
75-20 REPAIRS
Pre-tensioner - seat belt - front -
deployment - off vehicle
$% 76.73.78
These guidelines are written to aid authorised
personnel to carry out the safe disposal of air bag
modules when removed from the vehicle.
Deploy
It is imperative that before any work is
undertaken on the SRS system, the
appropriate information is read thoroughly.
1.Check condition of deployment tool LRT-86-
003 and associated fly leads.
2.Position LRT-86-007/02 in vice, ensuring that
vice jaws grip tool above the bottom flange to
prevent possibility of tool being forced upwards
during detonation. Tighten vice.3.Fit and secure seat belt pre-tensioner to LRT-
86-007/02.

RESTRAINT SYSTEMS
REPAIRS 75-21
4.Connect deployment tool fly lead LRT-86-003/
04 to seat belt pre-tensioner.
5.Connect deployment tool LRT-86-003 to
deployment tool fly lead LRT-86-003/04.
6.Connect deployment tool LRT-86-003 to
battery.
7.Press deployment tool operating button to
deploy seat belt pre-tensioner.
WARNING: Ensure all personnel are at least
15 metres (50 feet) away from the air bag
module.
8.
9.Disconnect deployment tool from battery.
WARNING: During deployment parts of the
air bag module become hot enough to burn
you. Wait 30 minutes after deployment
before touching the air bag module.
10.Disconnect deployment tool fly lead from seat
belt pre-tensioner.
11.Remove seat belt pre-tensioner from holding
tool and place in a sealed bag, ready for
disposal.
NOTE: Do not transport deployed SRS
components in the vehicle passenger
compartment.12.Wipe down holding tools with a damp cloth and
remove from vice.
13.Transport deployed seat belt pre-tensioner to
designated area for incineration.
14. Do not re-use or salvage any parts of the
SRS system.

RESTRAINT SYSTEMS
75-22 REPAIRS
Airbag module - drivers
$% 76.74.01
WARNING: It is imperative that before any work
is undertaken on the SRS system the appropriate
information is read thoroughly.
WARNING: Always disconnect both battery leads
before beginning work on the SRS system.
Disconnect the negative battery lead first. Never
reverse connect the battery.
Remove
1.Remove the key from the starter switch.
Disconnect both battery leads, negative lead
first. Wait ten minutes before starting work.
2.Remove 2 Torx bolts securing air bag module
to steering wheel.
3.Release air bag module from steering wheel.
CAUTION: Do not allow the air bag module
to hang by the air bag harness.
4.Disconnect multiplug from air bag module. 5.Remove air bag module.
WARNING: Store the airbag module with the
deployment side uppermost. If it is stored
deployment side down, accidental
deployment will propel the airbag module
with enough force to cause serious injury.
WARNING: Store the airbag module or seat
belt pre-tensioner in a designated storage
area. If there is no designated storage area
available, store in the locked luggage
compartment/loadspace of the vehicle and
inform the workshop supervisor.
Refit
NOTE: If the airbag module is to be replaced,
the bar code of the new module must be
recorded.
1.Position air bag module and connect multiplug.
2.Fit air bag module to steering wheel and tighten
Torx bolts to 9 Nm (7 lbf.ft).
3.Connect battery leads, earth lead last.