1999 LAND ROVER DEFENDER ECU

82AIR CONDITIONING
4
REPAIR EVAPORATOR
Service repair no - 82.25.20
Remove
1.Remove battery cover.
2.Recover refrigerant from A/C system.See
Adjustment.
3.Remove 2 bolts securing A/C pipes to
evaporator.
4.Release pipes and discard’O’rings.
CAUTION: Immediately cap all air
conditioning pipes to prevent ingress of
dirt and moisture into the system.
5.Remove 2 screws and release fuse/relay bracket
from body and collect 2 spacers.
6.Remove 8 screws securing speakers to A/C
duct.
7.Disconnect speaker Lucars and remove
speakers.
8.Remove 4 screws and bolt securing A/C duct to
fascia panel.
ProCarManuals.com

82AIR CONDITIONING
6
REPAIR Refit
20.Clean TXV and mating face.
21.Lubricate new’O’rings with refrigerant oil and fit
’O’rings to pipes.
22.Position TXV and tighten Allen screws.
23.Position evaporator and fit sensor.
24.Position cover and tighten screws.
25.Clean pipes and mating faces.
26.Lubricate and fit new’O’rings, position pipes
and tighten Allen screw.
27.Connect trinary switch multiplug.
28.Position blower unit,tighten screws and connect
multiplugs.
29.With assistance position A/C duct assembly to
vehicle.
30.Connect drain pipe to evaporator.
31.Connect multiplug to relay bracket.
32.Align A/C duct to fascia, tighten securing bolt
and screws.
33.Position speakers and connect Lucars.
34.Position relay bracket and tighten bolts.
35.Clean pipes and mating face.
36.Lubricate and fit new’O’rings to evaporator
pipes.
37.Position pipes and tighten bolts to6Nm(4
lbf.ft).
38.Renew receiver drier.See this Section.
39.Recharge A/C system.See Adjustment.
ProCarManuals.com

WIPERS AND WASHERS
3
DESCRIPTION AND OPERATION Although windscreen wiper functionality remains the same, the mechanical architecture has undergone significant
changes. The body structure has undergone some minor changes to house the revised wiper linkage.
A modified wiper motor is introduced which is balanced to reduce operation noise. The brush plate is fitted with
capacitors to reduce radio interference and a thermal cut-out is introduced to prevent motor burnout. The motor
also contains a new park switch which also reduces operation noise. A common motor is now used on both LHD
and RHD variants.
The motor is repositioned on the bulkhead which allows a straighter drive cable run. The straighter run reduces
load on the cable allowing a stiffer cable to be used. The stiffer cable and the incorporation of a reduced friction
material reduces torsion wind-up of the cable and results in smoother wiper operation and a reduction of blade
over travel.
New, larger wheel boxes are fitted in an inverted position from the previous installation. The bulkhead mounting
holes are larger with flats for positive location of the wheel box spindle. The wheel boxes now feature a 40 tooth
gear ratio in lieu of a 32 tooth gear. This reduces backlash and load and further reduces blade over travel. The
wheel box casings are secured with locknuts.
The wheel box spindles now have a splined DIN taper fitting for the new wiper arms which are secured on the
spindle with an M8 nut. The taper improves arm retention.
A new grease is introduced which improves wiper operation at very low temperatures.
ProCarManuals.com

WIPERS AND WASHERS
1
REPAIR PUMP - WINDSCREEN WASHER
Service repair no - 84.10.21
Remove
1.Remove headlamp.See ELECTRICAL,
Repair.
2.Position drain tin to collect any fluid spillage.
3.Disconnect multiplug from washer pump.
4.Disconnect hose from washer pump.
5.Release washer pump from reservoir and
discard sealing washer.
Refit
6.Fit new sealing washer and secure pump to
reservoir.
7.Connect hose and multiplug to washer pump.
8.Fit headlamp.See ELECTRICAL, Repair.
9.Fill reservoir with screen cleaning fluid.JET - REAR SCREEN WASHER
Service repair no - 84.30.09
Remove
1.Release and remove both rear side window
finishers.
2.Remove 8 screws securing both rear grab
handles.
3.Remove both rear grab handles.
ProCarManuals.com

84WIPERS AND WASHERS
2
REPAIR
4.Remove 4 trim studs securing upper rear finisher
to body.
5.Release and remove upper rear finisher.
6.Position drain tin to collect any fluid spillage.
7.Disconnect washer tube from jet.
8.Remove nut securing washer jet to body.
9.Remove washer jet.
Refit
10.Fit washer jet to body and secure with nut.
11.Connect washer tube to jet.
12.Remove drain tin.
13.Fit upper rear finisher and secure with trim studs.
14.Fit both rear grab handles and secure with
screws.
15.Fit both rear side window finishers.ARM - WIPER - FROM 02MY
Service repair no - 84.15.02
Remove
1.Raise nut cover on wiper arm and remove nut.
2.Remove wiper arm from spindle.
NOTE: Do not carry out further
dismantling if component is removed for
access only.
3.Remove wiper blade.
Refit
4.Fit wiper blade.
5.Fit wiper arm to spindle and align blade to
windscreen.
6.Tighten nut securing wiper arm to17 Nm (13
lbf.ft),and fit cover.
ProCarManuals.com

WIPERS AND WASHERS
3
REPAIR WIPER MOTOR AND DRIVE RACK - FROM 02MY
Service repair no - 84.15.09
Remove
1.Disconnect battery negative lead.See
ELECTRICAL, Repair.
2.Remove wiper arms.See this Section.
3.Remove fascia console.See CHASSIS AND
BODY, Repair.
4.Remove air vent control knobs.
5.Remove 6 screws, remove fascia closing panel
and collect nut plate.
6.Move cover aside and loosen wiper motor drive
tube nut.
7.Remove 2 screws securing wiper motor, remove
retaining strap and mounting pad.
8.Disconnect multiplug from wiper motor.
9.Remove tube nut and remove wiper motor with
rack.
Refit
10.Lubricate wiper motor drive rack with grease.
11.Feed wiper motor rack into tube, connect
multiplug and fit but do not tighten tube nut.
12.Fit mounting pad and retaining strap, align wiper
motor and tighten screws.
13.Tighten wiper motor tube nut to8 Nm (6 lbf.ft)
and reposition nut cover.
14.Fit fascia closing panel.
ProCarManuals.com

84WIPERS AND WASHERS
4
REPAIR 15.Fit nut plate and fit screws to secure nut plate
and closing panel.
16.Fit knobs to air vent control levers.
17.Fit fascia console.See CHASSIS AND BODY,
Repair.
18.Fit wiper arms.See this Section.
19.Connect battery negative lead.See
ELECTRICAL, Repair.WHEELBOX/DRIVE PIVOT - FROM 02MY
Service repair no - 84.15.25
Remove
1.Disconnect battery negative lead.See
ELECTRICAL, Repair.
2.Remove steering column nacelle.See
STEERING, Repair.
3.Remove wiper motor and drive rack.See this
Section.
4.Remove 2 screws and move heater fan switch
aside.
5.Remove 2 screws securing drivers side demister
duct.
6.Disconnect demister tube and remove duct.
7.Remove bolt and nut and bolt securing steering
column support bracket and remove bracket.
8.Remove 11 screws securing fascia support rail.
ProCarManuals.com

WIPERS AND WASHERS
5
REPAIR
9.Remove cable ties securing washer tube to
windscreen wiper rack tube.
10.Loosen fully 4 nuts securing backplates to wheel
boxes and remove windscreen wiper rack tubes.
11.Remove seals from wheel box spindles.
12.Remove 2 nuts securing wheel boxes and
remove sealing washers.
13.Carefully pull fascia support rail from bulkhead
sufficiently to remove wheel boxes.
Refit
14.Loosen fully but do not remove nuts securing
wheel box back plates.
15.Grease wheel boxes.
16.Fit wheel boxes, fit sealing washers and tighten
nuts to5 Nm (3.7 lbf.ft).
17.Fit spindle seals.
18.Fit wiper rack tubes and tighten wheel box back
plate nuts sufficiently to hold tubes. Tighten
wheel box back plate nuts to6 Nm (4 lbf.ft)
after fitting windscreen wiper motor.
19.Align washer tube to rack tube and secure with
cable ties.
20.Align fascia support rail and secure with screws.
21.Fit steering column support bracket and tighten
bolt and nut and bolt to45 Nm (33 lbf.ft).
22.Fit demister duct to tube, align relay bracket and
secure duct with screws.
23.Position heater fan switch and secure with
screws.
24.Fit wiper motor and drive rack.See this
Section.
25.Fit steering column nacelle.See STEERING,
Repair.
26.Connect battery negative lead.See
ELECTRICAL, Repair.RELAY - WIPER DELAY - FROM 02MY
Service repair no - 84.15.37
Remove
1.Disconnect battery negative lead.See
ELECTRICAL, Repair.
2.Remove 4 screws securing instrument pack and
release pack from fascia.
3.Disconnect 2 multiplugs from warning lamp
panel.
4.Disconnect instrument pack multiplug from main
harness.
5.Remove instrument pack.
ProCarManuals.com