1999 LAND ROVER DEFENDER oil

AIR CONDITIONING
1
REPAIR COMPRESSOR
Service repair no - 82.10.20
Remove
1.Remove engine acoustic cover.See ENGINE ,
Repair.
2.Depressurise A/C system.See Adjustment.
3.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Disconnect multiplug from compressor.
6.Remove 2 bolts securing air conditioning pipes
to compressor and discard’O’rings.
CAUTION: Immediately cap all air
conditioning pipes to prevent ingress of
dirt and moisture into the system.
7.Release clips and disconnect top hose from
coolant elbow and heater pipe.
8.Remove 4 bolts securing compressor to
mounting bracket.
9.Remove compressor.Refit
10.Position compressor to mounting bracket and
tighten bolts to25 Nm (18 lbf.ft).
11.Remove caps from compressor and pipe
connections.
12.Clean compressor and pipe connections.
13.Lubricate new’O’rings with refrigerant oil and fit
to compressor.
14.Position A/C pipes to compressor and tighten
bolts to9 Nm (7 lbf.ft).
15.Connect multiplug to compressor.
16.Position top hose and secure with clips.
17.Refill cooling system.See COOLING SYSTEM,
Adjustment.
18.Fit auxiliary drive belt.See ELECTRICAL,
Repair.
19.Recharge A/C system.See Adjustment.
20.Fit engine acoustic cover.See ENGINE ,
Repair.
ProCarManuals.com

AIR CONDITIONING
3
REPAIR Refit
6.Position bracket to receiver drier and tighten
clamp bolt.
7.Position receiver to chassis and tighten bolts.
8.Remove plugs from A/C pipes.
9.Lubricate new’O’rings with refrigerent oil.
10.Fit’O’rings, position pipes and tighten bolts to8
Nm (6 lbf.ft).
11.Recharge A/C system.See Adjustment.RELAY - TEMPERATURE CONTROL - FROM 02MY
Service repair no - 82.20.40
Remove
1.Remove front speaker from drivers side.See
ELECTRICAL, Repair.
2.Release relay from support bracket.
3.Disconnect multiplug and remove relay.
Refit
4.Connect multiplug to relay and fit relay to
bracket.
5.Fit front speaker.See ELECTRICAL, Repair.
ProCarManuals.com

82AIR CONDITIONING
6
REPAIR Refit
20.Clean TXV and mating face.
21.Lubricate new’O’rings with refrigerant oil and fit
’O’rings to pipes.
22.Position TXV and tighten Allen screws.
23.Position evaporator and fit sensor.
24.Position cover and tighten screws.
25.Clean pipes and mating faces.
26.Lubricate and fit new’O’rings, position pipes
and tighten Allen screw.
27.Connect trinary switch multiplug.
28.Position blower unit,tighten screws and connect
multiplugs.
29.With assistance position A/C duct assembly to
vehicle.
30.Connect drain pipe to evaporator.
31.Connect multiplug to relay bracket.
32.Align A/C duct to fascia, tighten securing bolt
and screws.
33.Position speakers and connect Lucars.
34.Position relay bracket and tighten bolts.
35.Clean pipes and mating face.
36.Lubricate and fit new’O’rings to evaporator
pipes.
37.Position pipes and tighten bolts to6Nm(4
lbf.ft).
38.Renew receiver drier.See this Section.
39.Recharge A/C system.See Adjustment.
ProCarManuals.com

84WIPERS AND WASHERS
4
DESCRIPTION AND OPERATION REAR WIPER - FROM 02MY
1.Rear wiper relay
The rear wiper system is unchanged except for the addition of a wiper motor relay into the electrical circuit.
The new rear wiper relay is located in the tail door, below the wiper motor. The relay coil is energised by a feed
supplied from the rear wiper switch. When the relay contacts close, a feed is supplied via the ignition switch
(position II) and a fuse in the passenger compartment fuse box, through the relay contacts to the wiper motor.
ProCarManuals.com

ELECTRICAL
1
DESCRIPTION AND OPERATION SECURITY AND CENTRAL DOOR LOCKING
SYSTEM - FROM 02MY
The following description details the functionality and operation of the 10AS Security and Central Door Locking
(CDL) System fitted to 2002MY Defender. The system contains some new features and also retains some
features from previous Defender models. The alarm system and CDL system are controlled by the 10AS anti-theft
alarm ECU.
New door lock barrels are introduced and use the same key as the ignition switch barrel, thereby eliminating the
requirement for a separate key for the doors.
NOTE: Some markets will only have some of the features described and some will have no
security or central door locking functions.
The security system comprises the following components:
10AS anti-theft alarm ECU
Remote handset transmitters
Transponder coil
Volumetric sensor
CDL actuators
Bonnet switch
Driver’s door key barrel switch
Door switches
Bonnet switch
Battery Backed-Up Sounder (BBUS) or alarm sounder
Security LED
Engine immobilised warning lamp
Direction indicators
ProCarManuals.com

86ELECTRICAL
2
DESCRIPTION AND OPERATION SECURITY AND CENTRAL DOOR LOCKING
SYSTEM COMPONENTS - FROM 02MY
1.Engine immobilisation warning lamp
2.Security LED
3.Transponder coil
4.CDL actuators (tail door shown)
5.Immobilisation ECU (300Tdi models only)
6.Remote handset and key7.Door switches
8.Bonnet switch
9.Alarm sounder
10.Battery Backed Up Sounder (BBUS)
11.Anti-theft alarm ECU
12.Volumetric sensor
ProCarManuals.com

ELECTRICAL
7
DESCRIPTION AND OPERATION Alarm Sounders
1.Battery Backed Up Sounder (BBUS)
2.Alarm sounder
Two types of alarm sounder are available, dependant on the vehicle market configuration.
A Battery Backed-Up Sounder (BBUS) is used in some markets and located in the LH front wing, behind the
headlamp. This is a tamper proof sounder with its own power supply which allows it to continue operating even if
disconnected from the vehicle power supply. The BBUS is connected to a permanent battery supply via fuse 7 in
the under seat fuse box. Two further connections are made to the anti-theft alarm ECU and a fourth connection is
to an earth header. If the BBUS is disconnected without first being disarmed by the anti-theft alarm ECU, it will
operate for 4.5 minutes.
To disarm the BBUS, when the battery is to be disconnected for instance, the ignition must be turned on to
position II and back to the off position , after which a 17 second delay is initiated to allow the battery or BBUS
connector to be disconnected. If the BBUS sounds, it can be disarmed by unlocking the vehicle with the remote
handset.
Where a BBUS is not specified, a standard vehicle horn is used for the alarm sounder and is located in the LH
front wing, behind the headlamp. The sounder is operated by an alarm relay which is controlled by the anti-theft
alarm ECU. The relay receives a permanent battery supply via fusible link 6 in the under seat fuse box. The relay
coil is connected to the anti-theft alarm ECU which provides an earth for the coil when horn operation is required.
This operates the relay contacts and supplies battery voltage to the sounder, causing it to operate.
ProCarManuals.com

86ELECTRICAL
12
DESCRIPTION AND OPERATION IMMOBILISATION SYSTEM - FROM 02MY
Engine immobilisation is available on all 2002MY engine derivatives, although it is not available in selected
markets. On Td5 models, the immobilisation system is controlled directly by the anti-theft alarm ECU. On 300Tdi
models, the immobilisation system is controlled by an engine immobilisation ECU in conjunction with the anti-theft
alarm ECU.
When immobilisation occurs on Td5 models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the ECM disables the fuel pump relay and the glow plug relay.
When immobilisation occurs on 300Tdi models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the engine immobilisation ECU disables the fuel cut-off solenoid, the starter
motor solenoid and the glow plug relay.
Two types of immobilisation are available; passive and active.
Engine Immobilised Warning Lamp
The engine immobilised warning lamp is located in the instrument pack. The lamp is used by the anti-theft alarm
ECU to show that the engine is immobilised during an attempted engine start.
The warning lamp receives a battery supply from the ignition switch position I (aux) via the passenger
compartment fusebox. The anti-theft alarm ECU controls the warning lamp. When the warning lamp is not
required, the ECU supplies a battery supply to the warning lamp. When warning lamp operation is required, the
ECU provides an earth for the bulb.
If the ignition switch is moved to the crank position, but operation of the starter motor is prohibited and the engine
immobilised warning lamp flashes, then the anti-theft alarm ECU has not received the correct code from the
remote handset and the vehicle will remain immobilised. Ensure that the remote handset is in the proximity of the
transponder coil. If the remote handset is not available or inoperative, the immobilisation system can be disarmed
using the EKA procedure outlined later in this section.
If the ignition switch is turned to the crank position III and the remote handset is not in the proximity of the
transponder coil, engine immobilisation will remain active and the warning lamp will flash to inform the driver.
ProCarManuals.com