1999 LAND ROVER DEFENDER oil

54FRONT AXLE AND FINAL DRIVE
4
OVERHAUL 12.Examine all components, in particular, inner and
outer track, cage balls and bearing surfaces for
damage and excessive wear.
13.Maximum acceptable end-float on assembled
joint 0,64mm. Renew if worn or damaged.
Lubricate with a recommended oil during
assembly.
Fit constant velocity joint to axle
14.Fit collar and a new circlip.
15.Engage constant velocity joint on axle shaft
splines and using a soft mallet, drive joint in fully.
Renew stub axle, thrust ring, oil seal and bearing
16.Drill and chisel off thrust ring taking care to avoid
damaging stub axle.
17.Remove bearing and oil seal using special tool
TRT-37-004and slide hammerLRT-99-004.
Ensure lip of tool locates behind bearing to to
drive it out.
18.Repeat instruction for removal of oil seal.
19.Lubricate seal and lip with EP90 oil and with
cavity side leading press in a new oil seal using
special toolLRT-54-004.
20.Using special toolLRT-54-005, fit bearing with
its part number visible when fitted, and flush with
end face of stub axle.
21.Press fit a new thrust ring onto stub axle.
ProCarManuals.com

FRONT AXLE AND FINAL DRIVE
5
OVERHAUL Swivel pin housing
22.Remove bolts securing oil seal retaining plate
and joint washer. Release assembly from swivel
pin housing.
NOTE: Removal of oil seal and retaining
plate is achieved when swivel bearing
housing is removed.
23.Remove 2 bolts, retaining lower swivel pin to
housing.
24.Remove brake disc shield bracket.
25.Tap lug to remove lower swivel pin and joint
washer.
26.Remove two bolts retaining brake hose bracket
and top swivel pin.
27.Remove bracket, top swivel pin and shims.
28.Remove swivel pin housing while retrieving
lower and upper bearings.
Swivel bearing housing
29.Remove lower bearing track from swivel bearing
housing.
NOTE: Use upper bearing opening to gain
access to lower bearing track.
30.Remove 7 bolts retaining swivel bearing housing
to axle case.
31.Remove inner oil seal from back of housing.
32.Remove top bearing track from swivel bearing
housing.
NOTE: Use lower bearing opening to gain
access to upper bearing track.
33.If worn, pitted or damaged, renew housing.
34.Fit upper and lower bearing tracks into swivel
bearing housing.
CAUTION: Ensure bearing tracks are fitted
square or damage could occur.
35.With seal lips trailing, fit swivel housing inner oil
seal into rear of housing. Grease seal lips.
Fit swivel pin housing
36.Coat swivel bearing housing to axle casing bolts
with Loctite 270 or equivalent.
37.Coat both sides of joint washer with a sealing
compound. Position swivel bearing housing to
axle mating face.Swivel assembly components
1.Swivel pin housing
2.Top swivel pin and brake hose bracket
3.Upper and lower swivel pin bearings
4.Shim
5.Retaining plate and washer
6.Oil seal
7.Joint washer
8.Swivel bearing housing
9.Joint washer
10.Lower swivel pin
11.Mudshield bracket
12.Swivel housing inner oil seal
ProCarManuals.com

54FRONT AXLE AND FINAL DRIVE
6
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.25 Nm (18 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to65 Nm (48 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to track rod ball joint
bore and pull balance to determine effort
required to turn swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to65 Nm (48 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O’clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assemblySee FRONT
SUSPENSION, Repair. Front hub bearings.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See MAINTENANCE , Under vehicle
maintenance.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop boltsSee STEERING,
Adjustment. Steering lock stops.
ProCarManuals.com

STEERING
1
REPAIR STEERING COLUMN - UPPER - Td5
Service repair no - 57.40.01
Remove
1.Ensure road wheels and steering wheel are set
in the straight ahead position.
2.Loosen 2 clips securing air inlet pipe between
turbo and inlet air filter.
3.Remove air inlet pipe.
4.Mark relationship between the upper steering
column and the lower steering column universal
joint.
5.Remove bolt securing upper column to lower
column universal joint.
6.Remove steering colum nacelle.See this
Section.
7.Remove instrument pack.See
INSTRUMENTS, Repair.
8.Disconnect 3 column switch multiplugs.
9.Loosen column switch clamping screw.
10.Remove column switch assembly from steering
column.
11.Disconnect 4 Lucars from rear of ignition switch.
NOTE: Take note of Lucars correct fitted
position. Details can also be found in the
Electrical Reference Library.
12.Remove passive coil.See ELECTRICAL,
Repair.
13.Drill out 2 shear bolts securing ignition barrel to
column.
14.Remove ignition barrel.
ProCarManuals.com

STEERING
3
REPAIR Refit
NOTE: The steering column is a
non-servicable component and can only
be serviced as a complete assembly.
29.Fit mounting bracket to column and manouvre
assembly into position.
NOTE: Ensure marks on upper and lower
columns are aligned.
30.Loosely fit bolts securing mounting bracket to
bulkhead.
31.Fit upper clamp and rubber packing to column.
32.Loosely fit bolts securing upper clamp to
mounting bracket.
33.Loosely fit bolts securing 2 halves of upper
clamp.
34.Loosely fit bolts securing column lower mounting
bracket.
35.Fit bolt securing upper tie bar to steering column
and tighten to22 Nm (16 lbf.ft).
36.Tighten mounting bracket to bulkhead bolts,
clamp bolts, and lower mounting bolts.
M6 bolts =9 Nm (6 lbf.ft)
M8 bolts =22 Nm (16 lbf.ft)
37.Manouvre brake pedal box assembly and NEW
gasket into position in vehicle.
38.Tighten bolts securing brake pedal box to
bulkhead to25 Nm (18 lbf.ft)
39.Connect brake pedal switch Lucars.
40.Reposition mat to underside of fascia.
41.Secure ABS modulator multiplug to side of brake
pedal box.
42.Fit brake servo.See BRAKES, Repair.
43.Fit ignition switch to steering column, ensuring
inner shaft slot aligns with steering lock plunger.
44.Evenly tighten clamp bolts, but DO NOT shear at
this stage.
45.Temporarily fit steering wheel and check for
correct operation of switch and lock.
46.Remove steering wheel.
47.Fully tighten ignition switch bolts until heads
shear.48.Connect Lucars to rear of ignition switch.
49.Fit passive coil to ignition switch and connect
multiplug.
50.Fit switch assembly to steering column and
tighten clamping screw.
51.Connect column switch multiplugs.
52.Fit instrument pack.See INSTRUMENTS,
Repair.
53.Fit steering column nacelle.See this Section.
54.Fit bolt securing upper column to lower column
universal joint and tighten to25 Nm (18 lbf.ft).
55.Fit air inlet pipe between turbo and inlet air filter
and secure with clips.
ProCarManuals.com

77PANEL REPAIRS
18
SEALING AND CORROSION PROTECTION Seam Sealers
A heat cured, PVC Plastisol sealer is applied to joint
areas during factory assembly. This material is not
suitable for service use.
Carry out seam sealing after the application of primer
and before the surfacer and final paint coats. Ensure
that surfaces are first cleaned of all grease and oil.
Apply the sealer material to the joint as a bead, either
by hand or using an applicator gun. Where necessary,
brush sealer well into the joint and wipe smooth using
a cloth soaked with solvent such as Shell SBP3. This
will ensure an acceptable cosmetic finish.
Apply sealer to ALL accessible joints following repair
work. Be aware that damage to a vehicle can often
result in deflection to those areas of the body which
are remote from the impact. The sealers in these
areas can therefore be disturbed by subsequent
straightening and repair operations. Check joints in
the vicinity of the area undergoing repair for evidence
of cracked sealer, clean them out as required and
re-treat them with fresh sealer using the following
procedure:
Clean the affected joint or seam and
re-treat any exposed metal areas with a
suitable etch phosphate primer.
Treat affected area with an acid-etch
primer.
Apply appropriate seam sealer as
necessary.
Apply appropriate colour coat (and
underbody sealer as applicable).
Where joints are inaccessible following the
reassembly or fitment of components, ensure that a
paste-type sealer is applied to such joints. Certain
seams also become inaccessible after the completion
of panel repairs. In such instances the paint process
should be carried out and sealers applied before final
assembly.Provided access is adequate, apply the sealer to both
sides of the repair joint. Where access is limited to
one side only (e.g. box sections), inject the affected
box member with cavity wax.
CAUTION: ALWAYS deploy an extractor
unit to remove toxic fumes when using
oxy-acetylene equipment to remove panels
treated with wax and sealers.
The following Illustrations show the treatment areas
for Seam Sealing.
ProCarManuals.com

AIR CONDITIONING
1
ADJUSTMENT REFRIGERANT RECOVERY, RECYCLING,
RECHARGING
Service repair no - 82.30.02
WARNING: The air conditioning system is
charged with a high pressure, potentially
toxic refrigerant. Repairs or servicing must
only be carried out by an operator familiar with
both the vehicle system and the charging and
testing equipment.
WARNING: All operations must be carried
out in a well ventillated area away from
open flame and heat sources.
WARNING: Wear eye and hand safety
protection.
CAUTION: Overcharging air conditioning
system will cause excessive head
pressure.
An air conditioning portable Refrigerant Recovery
Recycling Recharging Station for use with R134a
refrigerant incorporates all the features necessary to
recover R134a refrigerant from the air conditioning
system; to filter and remove moisture; to evacuate and
recharge with the reclaimed refrigerant. The unit can
also be used for performance testing and air
conditioning system analysis.
The operator must adhere to the equipment
manufacturer’s instructions.
Refrigerant Recovery
1.Remove dust caps from high and low pressure
connectors.
2.Connect high and low pressure hoses to
appropriate connections.
3.Open valves on connectors.
4.Turn valves on refrigerant station to correct
positions.
NOTE: Operate the refrigerant station in
accordance with the manufacturers
instructions.
5.Turn Process switch to correct position.
6.Turn Main switch to’ON’.
7.Allow station to recover refrigerant from system.8.Close valves on refrigerant station.
9.Turn Main switch to’OFF’.
10.Close valves on connectors.
11.Disconnect high and low pressure hoses from
connectors.
12.Fit dust caps to connectors.
13.Open tap at rear of station to drain refrigerant oil
recovered from system.
14.Measure and record quantity of refrigerant oil
recovered from system.
15.Close tap at rear of station.
Evacuation
CAUTION: Whenever the refrigerant
system is opened, the receiver/drier must
be renewed immediately before evacuating
and recharging the system.
1.Remove dust caps from high and low pressure
connectors.
2.Connect high and low pressure hoses to
appropriate connections.
3.Open valves on connectors.
4.Turn valves on refrigerant station to correct
positions.
5.Turn Process switch to correct position.
6.Turn Main switch to’ON’.
7.Allow station to evacuate system.
NOTE: If the vacuum reading is below
700mmHg after 15 minutes, suspect a leak
in the system. Partially recharge the
system and check for leaks using an electronic
leak tester. Check suction lines first, then run the
compressor for 5 minutes. Next check the high
pressure lines.
NOTE: The system must be evacuated
immediately before recharging
commences. Delay between evacuation
and recharging is not permitted.
ProCarManuals.com

82AIR CONDITIONING
2
ADJUSTMENT Recharging
WARNING: Refrigerant must always be
recycled before re-use, to ensure that the
purity of the refrigerant is high enough for
safe use within the air conditioning system.
Recycling should always be carried out with
equipment which is design certified by
Underwriter Laboratory Inc. for compliance with
SAE-J1991. Other equipment may not re-cycle the
refrigerant to the required level of purity.
WARNING: A R134a Refrigerant Recovery
Recycling Recharging station must not be
used with any other type of refrigerant.
WARNING: R134a refrigerant from
domestic and commercial sources must
not be used in motor vehicle air
conditioning systems.
CAUTION: When a major repair has been
carried out, a leak test should be carried
out using inert gas.
1.Close valves on refrigerant station.
2.Close valve on oil charger.
3.Disconnect yellow hose from refrigerant station.
4.Remove lid from oil charger.
5.Pour correct quantity of refrigerant oil into oil
charger.
6.Fit lid to oil charger.
7.Connect yellow hose to refrigerant station.
8.Open valve on oil charger.
9.Move pointer on refrigerant gauge to mark
position of refrigerant drop.
10.Slowly open correct valve on refrigerant station
and allow vacuum to pull refrigerant into system.
11.Close valve on refrigerant station when correct
amount of refrigerant has been drawn into air
conditioning system.
12.If the full charge is not accepted by the system,
start the engine and run it at 1,500 rev/min for a
minimum of 2 minutes. Switch on the air
conditioning system, open the vehicle windows,
set the temperature control to cold and the
blower switch to maximum.
13.Consult Refrigerant station instruction manual for
correct procedure to complete the charge.
14.Turn Main switch to’OFF’.
15.Close valves on connectors.
16.Disconnect high and low pressure hoses from
connectors.
17.Fit dust caps to connectors.
18.Carry out performance test on air conditioning
system.
ProCarManuals.com