1999 GMC C-SERIES manual transmission
[x] Cancel search: manual transmissionPage 59 of 328
yellowblue
2-17
The accelerator and clutch pedals must be released in
order for the exhaust brake to engage. Whenever the
exhaust brake is active, the light in the switch will be on.
Do not use the exhaust brake when running the engine at
idle during warm
-up or other extended periods.
Prolonged use of the exhaust brake during idling will
cause the engine to overheat.
CAUTION:
Be careful when using the exhaust brake or you
could lock the wheels and lose control of the
vehicle. Operators not familiar with an exhaust
brake should not use this brake on slippery
surfaces before learning to use it on dry surfaces.
If the vehicle's wheels begin to lock when using
the exhaust brake on slippery surfaces, switch the
exhaust brake off immediately. The exhaust
brake will turn off if the anti
-lock brake system
is activated.
Tw o-Speed Rear Axle Electric Shift
Control (If Equipped)
If your vehicle has this feature, you'll find a label (or
labels) on the ceiling above the windshield or in another
place near the driver that show how to use it. Be sure
to follow the directions carefully. Use the following
directions based on the type of shift control you have.
Automatic Transmission
The switch for the rear axle
shift control is on the shift
tower to the right of the
shift lever.
When the switch is up, the rear axle is in the high range.
Push it down to get the low range.
ProCarManuals.com
Page 60 of 328
yellowblue
2-18
The two-speed axle should be in low range when you
park the vehicle. Apply the parking brake, shift to
PARK (P) or NEUTRAL (N) and shut off the engine.
To operate off
-road or under a heavy load, shift into low
range when the vehicle is standing still and then operate
the transmission normally.
On the highway, with the axle in low range and
transmission in top gear, you may shift the axle to high
range by raising the switch and releasing the accelerator
momentarily. Re
-apply the accelerator after your shift.
Under light load conditions, first shift the axle into the
high range with the vehicle at a standstill and then
operate the transmission normally.
Manual Transmission
The switch for the rear axle
shift control is on the shift
lever. When the switch is
up, the rear axle is in the
high range. Push it down to
get the low range.
The two
-speed axle should be in low when you park the
vehicle. You'll need to engage the transmission, even
move the vehicle a little, to be sure the axle is in the low
range. Then apply the parking brake, shift into
NEUTRAL and shut off the engine.
Also, always start the vehicle in motion with the
two
-speed axle in the low range. When you upshift the
rear axle from low to high, move the switch up for the
high range, disengage the clutch, pause, engage the
clutch and then press down on the accelerator. When
you shift the axle down from high to low, you don't
have to clutch. Just move the switch down to low,
release the accelerator and then quickly apply it again.
ProCarManuals.com
Page 61 of 328
yellowblue
2-19 Air Shift Control
(Manual Transmissions Only)
The lever for the rear axle
shift control is either at the
lower right corner of the
instrument panel or on the
shift lever.
When the lever is moved to HI, the rear axle will be in
the high range. Switch it to LOW to get the low range.
The two
-speed axle should be in LOW when you park
the vehicle.
You'll need to engage the transmission, even moving the
vehicle a little, to be sure the axle is in the low range.
Then apply the parking brake, shift into NEUTRAL and
shut off the engine.Also, always start the vehicle in motion with the
two
-speed axle in the LOW position. When you upshift
the rear axle from LOW to HI, move the lever to the
HI position, disengage the clutch, pause, engage the
clutch and then press down on the accelerator. When
you shift the axle down from HI to LOW, you don't
have to clutch. Just move the lever to LOW, release the
accelerator and then quickly press it down again.
Air Suspension (If Equipped)
Your vehicle may be equipped with the Hendrickson
HAS Series single
-axle air suspension which is designed
for single
-axle on-highway use. This feature is available
in the 19,000 lb. capacity and as a low profile option for
operations which require extra cubic capacity and a
reduced deck height.
With this air suspension system, the ride height is set
during vehicle assembly so that the vehicle has a constant
frame height. The system will then increase or decrease
air pressure in the air springs to maintain this height.
ProCarManuals.com
Page 62 of 328
yellowblue
2-20
Air Suspension Dump Control (If Equipped)
If your vehicle is equipped with the Hendrickson HAS
Series single
-axle air suspension, you may have this
control. The air suspension dump control allows the
operator to lower the deck height approximately
4.5 inches (11.5 cm) from the normal frame height.
The switch to deflate and
inflate the air suspension is
located on the upper left
side of the instrument panel
above the driver's side vent.
The light in the switch will be illuminated whenever the
switch is in the ªdumpedº position.
Automatic Transmission Operation
We build vehicles with four, five and six-speed
automatic transmissions. This part of the manual covers
the basics of these. With some of the transmissions, you
will find another manual in your vehicle that goes into
more detail. On the ceiling, in front of and above the
driver, or in some other place near the driver, you will
see a label that describes important operating facts about
the automatic transmission in your vehicle. Make sure
you follow the instructions on this label.
You may have a PARK (P) position for your shift lever.
This position locks your rear wheels. It is the best
position to use when you start your engine because your
vehicle can't move easily.
All vehicles equipped with automatic transmissions
can be started in PARK (P), if equipped, or in
NEUTRAL (N). When you shift out of NEUTRAL (N),
you may have to hold in a push button on the shift lever
or lift up on a release handle as you shift. See the
Allison Automatic Transmission Operator's Manual in
your vehicle for more information about this.
ProCarManuals.com
Page 63 of 328
yellowblue
2-21
CAUTION:
It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don't leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won't move, even when you're on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).
See ªShifting Into PARK (P)º in the Index.
CAUTION:
Shifting out of PARK (P) or NEUTRAL (N) while
your engine is ªracingº (running at high speed) is
dangerous. Unless your foot is firmly on the
brake pedal, your vehicle could move very
rapidly. You could lose control and hit people or
objects. Don't shift out of PARK (P) or
NEUTRAL (N) while your engine is racing.
Automatic Transmission Third Gear Hold
(If Equipped)
If you have this feature, your range selector has a
ª2
-3º position. You can't shift up to the next higher
gear when the transmission is in this position unless
your engine
-governed speed is exceeded, such as when
going downhill.
This feature is useful for certain load and traffic
conditions or when plowing snow. See the Allison
Automatic Transmission Operator's Manual in your
vehicle for further information.
ProCarManuals.com
Page 64 of 328
yellowblue
2-22
Manual Transmission Operation
This part of the manual covers the basics of the manual
transmission. With some of the transmissions, you
will find another manual in your vehicle that goes into
more detail.
Using the Clutch
When you're starting to move the vehicle, it's important
to begin with the engine speed at idle. Then start to
engage the clutch and listen for an engine speed drop of
about 100 rpm. At this point, the clutch is engaging, so
you should increase the engine speed and fully engage
the clutch. It's important not to increase the engine
speed sooner or before the clutch begins its engagement.
If you do, you can cause damage to your vehicle.
Double-Clutching
You must use the ªdouble-clutchingº method when you
shift an unsynchronized gear set. Simply disengage the
clutch, shift to NEUTRAL (N) and engage the clutch.
When you're shifting down to a lower gear, accelerate
the engine speed while in NEUTRAL (N) to get ready
for the lower gear.
Eaton Fuller 5 and 6-Speed Transmissions
and Dana Spicer 7-Speed Transmissions
These transmissions have gears that automatically
synchronize when you shift up or down (except
FIRST (1) gear on the five
-speed transmission which is
unsynchronized). Choose the gear which will maintain
the road speed you want while keeping the engine above
two
-thirds of the governed speed. When the engine
speed drops below two
-thirds of the governed speed,
shift into the next lower gear before your engine begins
to lug. When you shift down, be sure to double
-clutch
if required.
Eaton Fuller 9 and 10-Speed
Manual Transmissions
If your vehicle has one of these unsynchronized
transmissions, it's naturally somewhat complicated.
The label above the windshield will tell you the
operating basics you need to know.
Before operating the vehicle with one of these
transmissions, be sure to read the Eaton Fuller
Transmission Driver Instructions Manual in your vehicle.
ProCarManuals.com
Page 65 of 328
yellowblue
2-23 Eaton Fuller Transmission with Clutch
Brake (Option)
Some vehicles have an optional clutch brake. It engages
when you push your clutch pedal all the way to the
floor. Use it when you shift into first or reverse gear.
Press the clutch pedal as far as it will go and then make
your shift. If the engagement isn't smooth when you
engage the clutch, press the clutch pedal in and then
immediately re
-engage it. Use the clutch brake only
with the engine idling and the vehicle standing still.
If you have this feature, see the Eaton Fuller
Transmission Driver Instructions Manual before
operating your vehicle.
Eaton Fuller Transmission with
Countershaft Brake (If Equipped)
The countershaft brake is used when you shift from a
standing start into FIRST (1) or REVERSE (R). You
will find this feature on vehicles with gasoline engines
and Eaton Fuller 9 or 10
-speed transmissions.
See the Eaton Fuller Transmissions Driver
Instructions Manual.
Parking
CAUTION:
If you don't park your vehicle properly, it can
roll. If you've left the engine running, it can move
very quickly. You or others could be injured.
To be sure your vehicle won't move, even when
you're on level ground, follow the steps below.
Two-Speed Rear Axle
1. With the engine running, shift the two-speed rear
axle into low. To be sure it's in low, you'll need to
move the vehicle in gear just a little.
2. Hold the regular brake pedal down with your
right foot.
3. Apply the parking brake.
4. Shift the transmission to NEUTRAL (N) or
PARK (P).
ProCarManuals.com
Page 66 of 328
yellowblue
2-24 Hydraulic Brakes
If your vehicle has hydraulic brakes, it has a parking
brake lever or an electric/hydraulic parking brake. The
lever is below the instrument panel to the left of the
steering column. The electric/hydraulic parking brake
knob is to the right of the steering column.
Your vehicle may also be equipped with an automatic
transmission which has a shift lever. This lever will have
a PARK (P) position on the shift indicator. When the
PARK (P) position is selected with the shift lever, the
parking brake is automatically applied.
Propshaft Brake Burnish Procedure
It is recommended that the propshaft-mounted parking
brake be burnished as part of the new vehicle break
-in.
The parking brake will work best after it has been
burnished following these instructions.
Make 10 stops, using the parking brake hand lever, from
20 mph (32 km/h) about 2 1/2 miles (4 km) apart.
Between stops, drive the vehicle at 20 mph (32 km/h).
Lever Operated Parking Brake
To apply the parking brake,
pull the lever all the way up.
The PARK BRAKE light
will come on when the
parking brake is applied.
Then shift the transmission
to NEUTRAL (N) or
PARK (P).
The vehicle must be stopped when applying the parking
brake, except while burnishing the parking brake linings
(see ªPropshaft Brake Burnish Procedureº in the Index).
You can easily adjust the parking brake by turning the
knob on the lever. Turning it clockwise makes the brake
grip more tightly. It will also make the lever seem harder
to pull up. Turning the knob counterclockwise makes the
parking brake apply less firmly. Adjust the parking
brake only when the lever is down (released).
ProCarManuals.com